Major tech MTD70T Manuel utilisateur
MTD70T
600A AC TRUE RMS
DIGITAL CLAMP METER
INSTRUCTION MANUAL
2
Contents Page no
3
1. Safety..............................................................................................4
1.1. International Safety Symbols......................................................4
1.2. Safety Notes.............................................................................4
1.3. Warnings.................................................................................4
1.4. Cautions..................................................................................4
2. Descriptions.....................................................................................5
2.1. Meter Descriptions....................................................................5
2.2. Display Icons............................................................................5
3. General Specifications........................................................................6
4. Specifications...................................................................................6
4.1. AC True RMS Current.................................................................6
4.2. AC Voltage True RMS..................................................................7
4.3. DC Voltage...............................................................................7
4.4. Resistance................................................................................7
4.5. Diode and Continuity..................................................................8
5. Operation.........................................................................................8
5.1. AC Current Measurements..........................................................8
5.2. AC Voltage Measurements..........................................................9
5.3. DC Voltage Measurements.........................................................9
5.4. Resistance Measurements..........................................................9
5.5. Continuity Measurements..........................................................9
5.6. Diode Test................................................................................9
5.7. Non-Contact AC Voltage Measurements.....................................10
5.8. Data HOLD.............................................................................10
5.9. Flashlight & LCD Backlight........................................................10
5.10. Range Function.......................................................................10
5.11. Automatic Power OFF...............................................................10
6. Maintenance...................................................................................11
6.1. Cleaning and Storage...............................................................11
6.2. Battery Replacement...............................................................11
4
This symbol, adjacent to another symbol or terminal, indicates the user
must refer to the manual for further information.
This symbol, adjacent to a terminal, indicates that, under normal use,
hazardous voltages may be present.
Double insulation.
Application around and removal from uninsulated hazardous live
conductors is permitted.
1. SAFETY
!
1.1. lnternational Safety Symbols
1.2. Safety Notes
• Do not exceed the maximum allowable input range of any function.
• Do not apply voltage to meter when resistance function is selected.
• Set the function switch OFF when the meter is not in use.
• Remove the battery if meter is to be stored for longer than 60 days.
1.3. Warnings
• Set function switch to the appropriate position before measuring.
• When measuring volts do not switch to current/resistance modes.
• Do not measure current on a circuit whose voltage exceeds 600V.
• When changing ranges always disconnect the test leads from the circuit
under test.
1.4. Cautions
• Improper use of this meter can cause damage, shock, injury or death.
Read and understand this user manual before operating the meter.
• Always remove the test leads before replacing the battery or fuses.
• Inspect the condition of the test leads and the meter itself for any damage
before operating the meter. Repair or replace any damage before use.
• Use great care when making measurements if the voltages are greater
than 25VAC RMS or 35VDC. These voltages are considered a shock hazard.
• Always discharge capacitors and remove power from the device under test
before performing Diode, Resistance or Continuity tests.
• Voltage checks on electrical outlets can be difficult and misleading because
of the uncertainty of connection to the recessed electrical contacts. Other
means should be used to ensure that the terminals are not "live".
• If the equipment is used in a manner not specified by the manufacturer,
the protection provided by the equipment may be impaired.
A AC 600A AC
V DC, V AC 1000V DC/AC
Resistance, Capacitance, Frequency, 250V DC/AC
Diode Test, Temperature.
Maximum InputFunction
5
2.1. Meter Descriptions
1 - NCV Test
2 - Current clamp
3 - LED Flashlight
4 - Non-contact AC voltage indicator light
5 - Clamp trigger
6 - Rotary Function switch
7 - SELECTOR mode range button
8 - Data Hold button
9 - REL button for Relative Measurement
10 - Flashlight and LCD backlight button
11 - LCD display
12 - COM input jack
13 - V Ω Diode Continuity CAP TEMP Hz% jack
14 - Battery Cover
2. Descriptions
2
5
7
1
9
11
12
3
4
6
8
10
13
14
Button Operation Performed
HOLD Data Hold
Minus sign Negative reading display
0 to 3999 Measurement display digits
NCV Non-Contact Voltage
AUTO Auto Range mode
DC Direct Voltage
AC Alternating Current/Voltage
Low battery
mV or V Milli-volts or Volts (Voltage)
Ω Ohms (Resistance)
A Amperes (Current)
F Farad (Capacitance)
Hz/% Hertz (Frequency)/Percent(duty ratio)
°C Celsius units (Temperature)
n, m, μ, M, k Unit of measure prefixes: nano, milli, micro, mega, and
kilo
Continuity test
Diode test
2.2. Display Icons
6
RangeBasic Functions
3. General Specifications
Clamp jaw opening 28mm approx.
Display 2000 Count (2-1/2 digits backlit LCD)
Low Battery indication is displayed
Over-range indication 'OL' display
Measurement rate 3 readings per second, nominal
Input Impedance 10M (VDC and VAC)
AC response Average Reading (AAC and VAC)
ACV Bandwidth 2KHZ
Operating Temperature 5°C to 40°C (41°F to 104°F)
Storage Temperature -20°C to 60°C (-4°F to 140°F)
Operating Humidity Max 80% up to 31°C (87°F) Decreasing
linearly to 50% at 40°C (104°F)
Storage Humidity <80%
Operating Altitude 2000meters (7000ft.) maximum.
Battery 2 x 1.5V AAA Battery
Battery life Approx. 30h (backlight ON), Approx.
100h (backlight OFF)
Auto power OFF After approx. 15 minutes
Dimensions 185 x 65 x 37mm
Weight 180g
Safety For indoor use and in the requirement
For double insulation IEC1010-1(2001):
EN61010-2-030, EN61010-2-032,
EN61010-2-033 Over voltage Category
III 600V, Pollution Degree 2.
4. Specifications
2.000A 1mA ±3.0% of rdg±5 digits
20.00A 10mA
200.0A 100mA ±2.0% of rdg±5 digits
600A 1A
Range Resolution
4.1. AC True RMS Current
Accuracy (% of reading + digits)
Over range protection: Maximum input 600A
Accuracy specified from 5% to 100% of the measuring range
Frequency Response: 50Hz to 60Hz True RMS
200mV 0.1mV ±1.5% of rdg±10 digits
2.00V 1mV
20.0V 10mV ±1.0% of rdg±5 digits
200V 0.1V
600V 1V ±1.2% of rdg±5 digits
Range Resolution
4.2. AC Voltage True RMS
Accuracy (% of reading + digits)
Input impedance 10MΩ. protection 600V DC or RMS of AC.
Frequency response 60V at 40Hz to 1kHz (sine), other ranges 50/60Hz
(all wave).
200mV 0.1mV
2.00V 1mV ±0.5% of rdg±5 digits
20.0V 10mV
200V 0.1V
600V 1V ±1.2% of rdg±5 digits
Range Resolution
4.3. DC Voltage
Accuracy (% of reading + digits)
Input impedance on 200mV range >40MΩ all other ranges 10MΩ.
Overload protection 600V DC or RMS of AC.
Input Protection: 250V DC or Peak value of AC.
Note: a. On 200Ω range, short the test leads to measure lead resistance,
then subtract the value from the real measurement.
b. When measuring resistance over 1MΩ, it is normal that the
reading reacts slowly, wait until reading is stable.
200.0Ω 0.1Ω ±0.8% of rdg±5 digits
2.000kΩ 1Ω
20.00kΩ 10Ω ±0.8% of rdg±1 digits
200.0kΩ 100Ω
2.000MΩ 1kΩ
20.00MΩ 10kΩ ±1.2% of rdg±5 digits
Range Resolution
4.4. Resistance (Auto Ranging)
Accuracy (% of reading + digits)
7
Diode Forward DCA is approx. 0.8mA, Forward voltage drop
open circuit Voltage MAX. 2.2V of Diode
Continuity Test current MAX. 1.5mA Buzzer makes a continuous
sound while resistance is
less than (50Ω)
Function Testing Condition
4.5. Diode & Continuity
Reading
Input Protection: 250V DC or 250V AC RMS
Warning DO NOT apply voltage to Continuity range
5.1. AC Current Measurements
1. Set the Function switch to the 200A/600A range if the approximate range
of the measurement is not known.
2. Set Function switch to 2A/20A for low current readings.
3. Press the trigger to open jaw. Fully enclose only one conductor. For
optimum results, center the conductor in the jaw.
4. The clamp meter LCD will display the reading.
NOTES: Read and understand all Warning and Caution statements in
this manual prior to using this meter. Set the function select switch to
the OFF position when the meter is not in use.
WARNING: Ensure that the test leads are disconnected from the meter
before making current clamp measurements.
5. Operation
CORRECTINCORRECT
5.2. AC Voltage Measurements
1. Insert the black test lead into the negative COM terminal and the red
test lead into the positive V/Ω terminal.
2. Set the function switch to the V~ position.
8
9
5.3. DC Voltage Measurements
1. Insert the black test lead into the negative COM terminal and the red
test lead into the positive V/Ω terminal.
2. Set the function switch to the V position.
3. Connect the test leads in parallel to the circuit under test.
4. Read the voltage measurement on the LCD display.
5.4. Resistance Measurements
1. Insert the black test lead into the negative COM terminal and the red
test lead into the positive V/Ω terminal.
2. Set the function switch to the Ω position.
3. Touch the test probe tips across the circuit or component under test. It
is best to disconnect one side of the device under test so the rest of the
circuit will not interfere with the resistance reading.
4. For Resistance tests, read the resistance on the LCD display.
5.5. Continuity Measurements
1. Insert the black test lead into the negative COM terminal and the red
test lead into the positive V/Ω terminal.
2. Set the function switch to the position.
3. Use SELECT Button to select . The display icons will change when the
SELECT button is pressed.
4. Touch the Test Probe tips across the circuit or component under test.
5. If the resistance is <50Ω, the buzzer tone will sound.
5.6. Diode Test
1. Insert the black test lead into the negative COM terminal and the red
test lead into the positive V/Ω terminal.
2. Set the function switch to position
3. Use SELECT Button to select . The display icons will change when the
SELECT button is pressed.
4. Touch the test probe tips to the diode or semiconductor junction under
test. Note the meter reading.
5. Reverse the test lead polarity by reversing the red and black leads. Note
the reading
6. The diode or junction can be evaluated as follows:
• If one reading displays a value (typically 0.400V to 0.900V) and the
other reading displays OL, the diode is good.
• If both readings display OL device is open.
• If both readings are very small or "0", the device is shorted.
3. Connect the test leads in parallel to the circuit under test.
4. Read the voltage measurement on the LCD display.
10
5.7. Non-Contact AC Voltage Measurements
1. Touch the probe tip to the hot (LIVE) conductor or insert into the hot
(LIVE) side of the electrical outlet.
2. If AC voltage is present, the detector red LED light will illuminate.
a. NOTE: The conductors in electrical cord sets are often twisted. For
best results, rub the probe tip along a length of the cord to
assure placing the tip in close proximity to the live conductor.
b. NOTE: The detector is designed with high sensitivity. Static electricity
or other sources of energy may randomly trip the sensor. This
is normal operation.
WARNING: Risk of Electrocution. Before use, always test the Voltage
Detector on a known live circuit to verify proper operation
5.8. Data HOLD
To freeze the LCD reading, press the HOLD button. While data hold is
active, the HOLD icon appears on the LCD. Press the HOLD button again
to return to normal operation.
5.9. Flashlight & LCD Backlight
The LCD is equipped with backlighting for easier viewing, especially in
dimly lit areas. Press the button for 3 seconds to turn the Flashlight and
LCD backlight on. Press once again to turn the Flashlight and
backlight off. The both work simultaneously.
5.10. Range Function
Press the RANGE key to activate the manual mode and to disable the Auto
range function. The symbol “AUTO” disappears from the upper left part of
the display. In manual mode, press the RANGE key to change measuring
range: the relevant decimal point will change its position. The RANGE key
is not active in positions , . In Auto range mode, the instrument
selects the most appropriate ratio for carrying out measurement. If a
reading is higher than the maximum measurable value, the indication “OL”
appears on the display. Press and hold the RANGE key for more than 1
second to exit the manual mode and restore the Auto range mode.
5.11. Automatic Power OFF
In order to conserve battery life, the meter will automatically turn off after
approximately 15 minutes. To turn the meter on again, turn the rotary
function switch to the OFF position and then to the desired function range.
To cancel the auto power off function, press SELECT button and turn on
the power with the rotary switch at the same time.
Table des matières
Autres manuels Major tech Instrument de mesure
Major tech
Major tech MT900 Manuel utilisateur
Major tech
Major tech MT930 Manuel utilisateur
Major tech
Major tech MT957 Manuel utilisateur
Major tech
Major tech MT935 Manuel utilisateur
Major tech
Major tech MT723 Manuel utilisateur
Major tech
Major tech MT960 Manuel utilisateur
Major tech
Major tech MT945 Manuel utilisateur
Major tech
Major tech MT123 Manuel utilisateur
Major tech
Major tech MT150 Manuel utilisateur
Major tech
Major tech MT941 Manuel utilisateur
Major tech
Major tech MT155 Manuel utilisateur
Major tech
Major tech MT920 Manuel utilisateur
Major tech
Major tech MT873 Manuel utilisateur
Major tech
Major tech MT948 Manuel utilisateur
Major tech
Major tech MT942 Manuel utilisateur
Major tech
Major tech MT940 Manuel utilisateur
Major tech
Major tech MT730 Manuel utilisateur
Major tech
Major tech MT402 Manuel utilisateur
Major tech
Major tech MT975 Manuel utilisateur
Major tech
Major tech MT775 Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur