Major tech MT950 Manuel utilisateur

INSTRUCTION MANUAL

MT950

NON-CONTACT TACHOMETER

Warning

To avoid injuries to animal or human eyes, please do not point the laser beam

in eyes or look directly into beam. If the instrument is not to be used for any

extended period, remove the battery.

Features

1. Provides fast and accurate non-contact RPM and surface speed

measurements of rotating objects.

2. Uses the CPU technique, photoelectrical technique, and junction laser

technique for one instrument combined PHOTO TACH. (RPM&REV)

3. Two test modes: rotate speed mode (unit: RPM) & count mode (unit:

REV)

4. Wide measure range and high resolution.

5. High visible digital LCD and Backlight display.

6. Built-in memory recalls Max Min and Last value stored.

Specifications

Display

5 digits LCD display

Accuracy

±(0.05% + 1 digits)

RPM Test Range

2 to 99,999 RPM

Count Range

1 to 99,999 REV

Resolution 0.1 RPM (2 to 999.9 RPM)

1 RPM. (over 1000 RPM)

Sampling Time

0.5 seconds (over 120 RPM)

Detecting Distance

50mm to 500mm

Time Base

Quartz crystal

Power Consumption

Approx. 45mA

Battery

9V or 6V Exterior DC

Operation Temp

0℃to 50℃

Dimension

160 x 58 x 39mm

Weight

151g

Measuring Manual

Apply a reflective mark to the object being measured. Hold down the MEAS

button and align the visible light beam with the applied target. Verify that

monitor indicator lights when the target aligns with the beam. The meter turns

on with the previously used mode. If you need to change the mode, release the

MEAS button and press the MODE button to change between RPM and REV.

Hold down MEAS to activate the new mode. The instrument auto powers off in

10 sec after releasing the MEAS button. Press the MEM button to recall the

last measurement readings for the Max, Min and Last value.

Measuring Considerations

1. Reflective Mark

•Cut the adhesive tap provide into approx. 12mm (0.5″) squares and

apply one square to each rotation shaft.

•The non-reflective area must always be greater than the reflective area.

•If the shaft is normally reflective, it must be covered with black tape or

black paint before attaching reflective tape

•Shaft surface must be clean and smooth before applying reflective tape.

2. Very Low RPM Measurement

•As it is easy to get high resolution and fast sampling time, if measuring

the very low RPM values, suggest user to attach more “REFLECTIVE

MARKS” averagely. Then divide the reading shown by the number of

“REFLECTIVE MARKS” averagely. Then divide the reading shown by the

number of “REFLECTIVE MARKS” to get the real RPM

Table des matières

Autres manuels Major tech Instrument de mesure

Major tech

Major tech MT785 Manuel utilisateur

Major tech

Major tech MT350 Manuel utilisateur

Major tech

Major tech MT26 Manuel utilisateur

Major tech

Major tech MT775 Manuel utilisateur

Major tech

Major tech MT940 Manuel utilisateur

Major tech

Major tech MT775 Manuel utilisateur

Major tech

Major tech MT874 Manuel utilisateur

Major tech

Major tech MT90 Manuel utilisateur

Major tech

Major tech MT760 Manuel utilisateur

Major tech

Major tech TRUERMS MTD80 Manuel utilisateur

Major tech

Major tech K2007R Manuel utilisateur

Major tech

Major tech MT760 Manuel utilisateur

Major tech

Major tech MT975 Manuel utilisateur

Major tech

Major tech MTD75T Manuel utilisateur

Major tech

Major tech MT155 Manuel utilisateur

Major tech

Major tech MT91 Manuel utilisateur

Major tech

Major tech MT740 Manuel utilisateur

Major tech

Major tech MT123 Manuel utilisateur

Major tech

Major tech MT782 Manuel utilisateur

Major tech

Major tech MT876 Manuel utilisateur

Major tech

Major tech MT402 Manuel utilisateur

Major tech

Major tech MT930 Manuel utilisateur

Major tech

Major tech MT766 Manuel utilisateur

Major tech

Major tech MT150 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur