M-system R5-MS Manuel utilisateur

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Potentiometer input module ............................................. (1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

• The equipment must be mounted inside the instrument

panel of a metal enclosure.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

■HOT INSERTION/REMOVAL OF MODULES

• Removing or replacing modules does not affect other mod-

ules on the same backplane. It is possible to replace them

without removing the power supply. However, replacing

multiple modules at once may greatly change line voltage

levels. We recommend that you replace them one by one.

■GENERAL PRECAUTIONS

• DO NOT set the switches while the power is supplied.

The switches are used only for maintenance without the

power.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

INSTALLATION

Use the Installation Base (model: R5-BS).

POTENTIOMETER INPUT MODULE MODEL R5-MS

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-6146 Rev.2 P. 1 / 3

INSTRUCTION MANUAL

COMPONENT IDENTIFICATION

■FRONT VIEW

RUN LED

Zero/Span Adj.

Mode Selector

456

123

RUN

SET

SET Button

Euro Type

Connector Terminals

■ZERO/SPAN ADJ. MODE SELECTOR ROTARY SW

SW MODE FUNCTION RUN LED

0 (*) Run Output % proportional to the Input % Red/Green ON *1

1 Input 1 0% adjust Apply 0% input at Input 1 and press SET Red Blinking

2 Input 1 100% adjust Apply 100% input at Input 1 and press SET Red Blinking

3 Input 2 0% adjust Apply 0% input at Input 2 and press SET Green Blinking

4 Input 2 100% adjust Apply 100% input at Input 2 and press SET Green Blinking

5 – 9 Not used

(*) Factory setting

*1. RUN indicator: Bi-color (red/green) LED; Red when the bus A operates normally; Green when the bus B operates normally; Amber

when both buses operate normally.

• Zero/Span Adjustment Modes

Run Mode

Normal operating mode

Input 0% Adjustment Mode

Apply the actual 0% input and press SET.

Input 100% Adjustment Mode

Apply the actual 100% input and press SET.

• How to Operate

1) Start up in Monitor Mode (SW position = 0) and wait for 2 or 3 seconds.

2) Switch to another mode and go through the adjustments.

3) Reset the switch to the position ‘0’ so that the new setting is stored in the internal memory.

• Cautions on the LEDs

1) Mode switching from Run to another mode becomes effective when SET button is touched and the LED for the respective

mode starts blinking after the rotary switch setting has been changed.

2) Mode switching back to Monitor becomes effective automatically in a few seconds after the switch is reset to ‘0’ and is con-

ﬁrmed with the LED stopping blinking.

PC CONFIGURATOR

With conﬁgurator software, settings shown below are available.

Refer to the software manual of R5CON for detailed operation.

■CHANNEL INDIVIDUAL SETTING

PARAMETER AVAILABLE RANGE DEFAULT SETTING

Zero Scale -32000 to +32000 0

Full Scale -32000 to +32000 10000

Bias [Zero Adj.] -320.00 to +320.00 0.00

Gain [Span Adj.] -32000 to +32000 1.0000

R5-MS

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-6146 Rev.2 P. 2 / 3

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■EXTERNAL DIMENSIONS unit: mm (inch)

456

123

6.5

(.26)

90 (3.54) LOCKING CLAMP

90 (3.54) 5.6

(.22)

18 (.71)

POSITIONING GUIDE

*Euro type connector terminals (4, 5 and 6) provided only with 2-ch. option.

■CONNECTION DIAGRAM

INPUT 1

INPUT 2

BUS CONNECTOR

INTERNAL POWER

*For dual redundant communication.

Note: The section enclosed by broken line is with 2-ch. option.

–

POTENTIOMETER

max.

min. 3

–

POTENTIOMETER

max.

min. 6

INTERNAL

BUS A

INTERNAL

BUS B*

WIRING INSTRUCTIONS

■EURO TYPE CONNECTOR TERMINAL

Applicable wire size: 0.2 to 2.5 mm2

Stripped length: 7 mm

R5-MS

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-6146 Rev.2 P. 3 / 3

Autres manuels M-system Instrument de mesure

M-system

M-system KADS Manuel utilisateur

M-system

M-system TR30 Manuel utilisateur

M-system

M-system 47 Series Manuel utilisateur

M-system

M-system 47LT Manuel utilisateur

M-system

M-system R7CWTU Manuel utilisateur

M-system

M-system 47LHZ Manuel utilisateur

M-system

M-system 43DV1-S Manuel utilisateur

M-system

M-system 47 Series Manuel utilisateur

M-system

M-system 47LCT Manuel utilisateur

M-system

M-system 47LCT Manuel utilisateur

M-system

M-system R1M-J3 Manuel utilisateur

M-system

M-system 47LV Manuel utilisateur

M-system

M-system R9EWTU Manuel utilisateur

M-system

M-system 48NV Manuel utilisateur

M-system

M-system JPSM Manuel utilisateur

M-system

M-system 47LLC Manuel utilisateur

M-system

M-system 47DM Manuel utilisateur

M-system

M-system 40LV Manuel utilisateur

M-system

M-system 47D Series Manuel utilisateur

M-system

M-system 47LPA Manuel utilisateur

M-system

M-system 73VR1100 Guide de l'utilisateur

M-system

M-system 47 Series Manuel utilisateur

M-system

M-system 47 Series Manuel utilisateur

M-system

M-system 48NAV Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur