M-system 73VR1100 Guide de l'utilisateur

– 1 –

73VR1100 PAPERLESS RECORDER

STARTUP GUIDE

– Read Before Installation –

Contents

1. POINTS OF CAUTION ...................................................................... 2

2. PACKAGE INCLUDES....................................................................... 5

3. ITEMS TO PREPARE........................................................................ 6

4. COMPONENT IDENTIFICATION ........................................................... 7

5. EXTERNAL DIMENSIONS.................................................................. 9

6. INSTALLING THE UNIT.................................................................... 10

7. PREPARATION & WIRING TO THE UNIT................................................ 12

8. SETTING UP THE RECORDER............................................................ 15

9. LET’S START RECORDING ............................................................... 23

EM-7399-A Rev.9

– 2 –

1. POINTS OF CAUTION

Thank you for choosing M-System. Before use, please read this manual carefully. If you

have any problems or questions with the product, please contact M-System’s Sales Office

or representatives.

This product is for use in general industrial environments, therefore may not be suitable

for applications which require higher level of safety (e.g. safety or accident prevention

systems) or of reliability (e.g. vehicle control or combustion control systems).

For safety, installation and maintenance of this product must be conducted by qualied

personnel.

■CONFORMITY WITH EC DIRECTIVES

• This equipment is suitable for use in a Pollution Degree 2 environment and in Installation

Category II. Reinforced insulation (alarm output to RUN contact output to power input

to FG/Ethernet/RS-485: 300V) is maintained. *

Prior to installation, check that the insulation class of this unit satises the system re-

quirements.

• The equipment must be mounted on a panel surface. Once mounted on a panel, take

appropriate precautions to prevent operators to be exposed to the terminal block*.

In order to enable the operator to turn off the power input immediately, install a switch or

a circuit breaker according to the relevant requirements in IEC 60947-1 and IEC 60947-

3 and properly indicate it*.

• Altitude up to 2000 meters*

• Insert a noise lter for the power source and RS-485 line connected to the unit. NEC

Tokin Noise Filter Model ESD-SR-250 or equivalent is recommended.

• The actual installation environments such as panel congurations, connected devices,

connected wires, may affect the protection level of this unit when it is integrated in a

panel system. The user may have to review the CE requirements in regard to the whole

system and employ additional protective measures to ensure the CE conformity.

*Except desktop type

■POWER INPUT

• Power input rating & operational range: Check the power rating for the unit on the speci-

cation label.

Rating 100 – 240V AC: 85 – 264V, 47 – 66 Hz,

approx. 15VA at 100V, approx. 20VA at 240V

Rating 24V DC: 24V ±10%, approx. 8W, 340mA

• Supplying any level of power other than specied above can damage the 73VR1100 or

the power source.

• The power cables and the signal I/O cables for the 73VR1100 must be located sepa-

rately.

• The main circuit cables (high voltage and high current), the signal I/O cables, and the

power cables should not be bundled together or placed near each other.

•

To increase noise resistance of the power input wires, twist the strands before connecting.

– 3 –

■SAFETY PRECAUTION

• Before you remove the unit, turn off the power supply and input signal for safety.

• Do not use the 73VR1100 in an environment where ammable gases are present. This

may result in an explosion.

• Do not disassemble or modify the 73VR1100 in any way. Doing so may result in a re

or an electrical shock.

• Do not strike the panel of the 73VR1100 with a hard, heavy or pointed object, or press

the panel with excessive force. Doing so may result in panel damage or injury.

• Do not block the 73VR1100’s ventilation openings or use it in areas where heat accu-

mulates. Additionally, do not store or use it under high-temperature conditions.

• Do not store or use the 73VR1100 in locations subject to direct sunlight, or where exces-

sive dust or dirt is present.

• The 73VR1100 is a precision instrument. Do not store or use it where large shocks or

excessive vibration can occur.

• Do not store or use the 73VR1100 in environments subject to chemical evaporation

(such as that of organic solvents), or where there are chemicals and/or acids present in

the air.

• Do not use paint thinner or organic solvents to clean the 73VR1100.

• Observe the environmental conditions when using the 73VR1100.

• Wait at least for 5 seconds before turning on the power supply after it has been turned

off. The 73VR1100 may not start up if the time interval is less than 5 seconds.

■ENVIRONMENT

• Indoor use

• The 73VR1100 is designed to be mounted on a vertical panel. It is not suitable for a

slanted or a horizontal panel surface.

• Environmental temperature must be within 0 to 50°C (32 to 122°F) with relative humidity

within 30 to 85% RH in order to ensure adequate life span and operation.

• Desktop type cannot be mounted on a panel surface.

• The handle and rubber feet cannot be detached from desktop type unit.

■GROUNDING

• Be sure to determine in advance the most stable grounding point in the environment

and earth the 73VR1100’s FG terminal and that of connected devices (PC) to it in order

to protect the devices from dielectric breakdown.

• Grounding is also effective to eliminate noise that could cause errors in the 73VR1100’s

operation.

■CF CARD

• Do not turn off the power supply to the 73VR1100 or reset it during recording. The CF

Card may be destroyed.

• Observe the described procedure when you need to replace the CF Card during record-

ing.

• Conrm the sides and the connector position of the CF Card when inserting one to the

card slot.

– 4 –

■LCD PANEL

• The LCD panel’s liquid contains an irritant. If the panel is damaged and the liquid con-

tacts your skin, rinse immediately the contact area with running water for at least 15

minutes. If the liquid gets in your eyes, rinse immediately your eyes with running water

for at least 15 minutes and consult a doctor.

• The following phenomena are LCD characteristics, and NOT a product defect:

- LCD screen may show uneven brightness depending upon displayed images or con-

trast settings.

- The LCD screen pixels may contain minute black-and-white-colored spots.

- The color displayed on the LCD screen may appear different when seen from outside

the specied viewing angle.

- When the same image is displayed on the screen for a long time period, an afterim-

age may appear when the image is changed. If this happens, turn off the 73VR1100

and wait 10 seconds before restarting it.

• To prevent an afterimage:

- Set the screensaver when you plan to display the same image for a long time pe-

riod.

- Plan to change the screen image periodically so that the same image does not remain

for the long time period.

■BACKLIGHT

• Even when the backlight is failed, the screen display can be controlled by touching it.

• Backlight failure is conrmed by the following phenomena:

- The screen gets dark even when no screensaver setting is enabled.

- If the screensaver is activated, the screen display does not recover when the screen

is touched.

• The backlight can be replaced in M-System factory. The LCD must be replaced at the

same time. Please consult M-System.

■INTERNAL CLOCK

• The internal clock data is stored in memory powered by a backup battery while the

73VR1100 is without external power supply.

• The data will be reset to its default status when the battery is used up while the 73VR1100

is left without power supply for a long time period. The clock adjustment will be nec-

essary once the power is restored. Please refer to the 73VR1100 Users Manual (EM-

7399-C, Section 5) for the procedure.

• Once the power is restored, the 73VR1100 starts recharging the battery. It will be full

in approximately in 36 to 48 hours.

■AND ....

• We recommend use of an UPS to supply power backups.

• The module is designed to function as soon as power is supplied, however, a warm up

for 10 minutes is required for satisfying complete performance described in the data

sheet.

– 5 –

2. PACKAGE INCLUDES...

Please conrm that all items mentioned below are included in the package.

Paperless Recorder

Software CD (73VRPAC2)

Startup guide (this booklet)

STARTUP GUIDE

Mounting bracket (two pieces)

Not included for desktop type.

– 6 –

3. ITEMS TO PREPARE

• CF card

Prepare one of the following model numbers:

1. Manufacturer: Hagiwara Solutions

Model No.: MCF10P-xxxxS (Alternative model: CFI-xxxxDG)

Capacity: 128 MB through 1 GB

2. Manufacturer: Apacer Technology

Model name: CFC III

Model No.: AP-CFxxxxE3ER-ETNDNRK Parts No.: 256 MB ... 81.2A010.1H34C

512 MB ... 81.2B010.1H34C

1 GB ... 81.2E010.1H34C

Model No.: AP-CFxxxxE3ER-ETNDNR Parts No.: 256 MB ... 81.2A010.1H10C

512 MB ... 81.2B010.1H10C

1 GB ... 81.2E010.1H10C

Capacity: 256 MB through 1 GB

• CF card reader

The CF card reader is required to read the card contents into a PC.

•

Refer to Users Manuals stored in the 73VRPAC2 CD for detailed operations of the 73VR1100.

Paperless Recorder (model: 73VR1100) Users Manual,

Connecting with I/O devices...................................................... No. EM-7399-B

Paperless Recorder (model: 73VR1100) Users Manual .................No. EM-7399-C

– 7 –

4. COMPONENT IDENTIFICATION

(2) Front Cover

(6) CF Card Access Indicator LED

(7) USB Connector

(3) CF Card Slot

(4) Eject Button

(5) Reset Button

(1) Touch Panel Screen

■FRONT VIEW

(1) Touch Panel Screen

Trend chart and other data views and setup views are displayed.

(2) Front Cover

Access to the CF Card Slot.

(3) CF Card Slot

Insert a CF Card.

(4) Eject Button

Used to retrieve the CF Card.

(5) Reset Button

Used to restart the 73VR1100.

(6) CF Card Access Indicator LED

Red light turns on during the CF Card is accessed.

(7) USB Connector

Connect an USB flash-memory.

– 8 –

■REAR VIEW

(8) RS-485 Terminal Block

Used to connect the 73VR1100 to its I/O devices via RS-485.

(9) LAN Port

Connects the LAN cable (10BASE-T or 100BASE-TX)

(10) RUN Output Indicator LED

Green light turns on in normal conditions; off when the RUN output contact is tripped

in an abnormality of the unit.

(11) Power Indicator LED

Light turns on while the power is supplied.

(12) Power Input Terminal

(13) RUN Output Terminal

(14) Alarm Output Terminal

(

) RUN Output Terminal

(9) LAN Port

(

) Alarm Output Terminal

(

) Power Input Terminal

(

) Power Indicator LED

(

) RUN Output Indicator LED

(8) RS-485 Terminal Block

ALM

–

(+)

(–)

RUN

–

– 9 –

5. EXTERNAL DIMENSIONS

Unit: mm (inch)

144 (5.67)

133 (5.24)

29.2

(1.15)

2 to 26 panel thickness

(.08 to 1.02)

Attach the mounting bracket either on the top/bottom or on the sides.

151.5 (5.96)

144 (5.67)

136.5 (5.37)

151.5 (5.96)

136.5 (5.37)

■PANEL MOUNT TYPE

– 10 –

144 (5.67) 133 (5.24)

29.2

(1.15)

144 (5.67)

136.5 (5.37)

■ DESKTOP TYPE

173 (6.81)

(.16)

(.98)

Table des matières

Autres manuels M-system Instrument de mesure

M-system

M-system 48NAVA Manuel utilisateur

M-system

M-system R5-MS Manuel utilisateur

M-system

M-system 47DAC Manuel utilisateur

M-system

M-system 47DT Manuel utilisateur

M-system

M-system 73VR21 Series Manuel utilisateur

M-system

M-system 47 Series Manuel utilisateur

M-system

M-system JPSM Manuel utilisateur

M-system

M-system 47LV Manuel utilisateur

M-system

M-system TR30 Manuel utilisateur

M-system

M-system 47LPT Manuel utilisateur

M-system

M-system M Series Manuel utilisateur

M-system

M-system SM10 Manuel utilisateur

M-system

M-system 47LT Manuel utilisateur

M-system

M-system 47NL Series Manuel utilisateur

M-system

M-system AS4M Manuel utilisateur

M-system

M-system 47 Series Manuel utilisateur

M-system

M-system R10-BS1 Manuel utilisateur

M-system

M-system 43DV1-S Manuel utilisateur

M-system

M-system M2EXM Manuel utilisateur

M-system

M-system JB2 Manuel utilisateur

M-system

M-system TR30 Manuel utilisateur

M-system

M-system R9WTU-ED Manuel utilisateur

M-system

M-system 47LV Manuel utilisateur

M-system

M-system 47LHZ Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur