M-system 47 Series Manuel utilisateur

47LT

P. 1 / 9ES-9512 Rev.1

Digital Panel Meters 47 Series

THERMOCOUPLE INPUT DIGITAL PANEL METER

(4-digit, LED display type) MODEL 47LT

Functions & Features

• 4-digit thermocouple input digital panel meter

• 1/8 DIN size

• Moving average function to suppress the dis-

play ﬂickering

• Max. and Min. value display

• IP66 front panel

• Separable terminal block

• Rear terminal cover for safety strapped to the

meter

Specications are subject to change without notice.

MODEL & SUFFIX CODE SELECTION

ORDERING INFORMATION

Specify code number. (e.g. 47LT-101G-M2)

GENERAL SPECIFICATIONS

Construction: Panel ﬂush mounting

Degree of protection: IP66; applicable to the front panel

for the meter mounted according to the

speciﬁed panel cutout

Connection: M3 screw terminals

(nickel plated steel; torque 0.6 N·m)

Material: Flame resistant resin (black)

Scaling: Programming via the front buttons

Averaging: None or moving average

Security: Prohibiting certain operations; protecting

settings

DISPLAY

Display: 16 mm (.63) high, 4 digits (-1999 to 9999),

LED

Scaling: No scaling (input temperature indication)

Decimal point position: 10 –1 or none (ﬁxed depending upon

the input type)

Minimum display/setting scale: 1°C or 1°F (0.1°C for K

and J, narrow span)

Read rate: Max. 40/second (25 milliseconds)

Over-range indication: ‘S.ERR’ ﬂashing when the input

signal is out of the usable range.

Burnout indication: ‘B.ERR’ ﬂashing

Alarm status indication*

LL indicator: Turns on when the LL alarm is tripped.

L indicator: Turns on when the L alarm is tripped.

H indicator: Turns on when the H alarm is tripped.

HH indicator: Turns on when the HH alarm is tripped.

P indicator: Turns on when none of the other alarms is

tripped.

Zero indication: Higher-digit zeros are suppressed.

Engineering unit indication: Sticker label attached

*Only ‘P’ turns on with no-alarm-output type. ‘LL’ or ‘HH’

does not turn on with dual-alarm-output type.

All setpoints can be independently set either for Hi or Lo

alarm trip.

Alarm/ Init/

Max/Min ShiftUp

Ini Alm D/P

Adj Fnc Min Max

(1.89)

mm (inch)

96 (3.78)

98.5 (3.88)

47LT–1❑❑❑–❑

MODEL

INPUT THERMOCOUPLE (eld-congurable)

1 : (PR), K (CA), E (CRC), J (IC), T (CC),

B (RH), R, S, N

DC OUTPUT

0 : None

Current

A : 4 – 20mA DC

D : 0 – 20mA DC

ALARM OUTPUT

0 : None

1 : N.O. relay contact, 4 points

2 : SPDT relay contact, 2 points

DISPLAY COLOR

R : Red

YR : Orange

G : Green

BG : Bluegreen

B : Blue

W : White

POWER INPUT

AC Power DC Power

: 100 – 240V AC R: 24V DC

Voltage

4 : 0 – 10V DC

5 : 0 – 5V DC

6 : 1 – 5V DC

4W : -10 – +10V DC

47LT

P. 2 / 9ES-9512 Rev.1

INSTALLATION

Power input

AC: Operational voltage range 85 – 264V

50/60 Hz, approx. 6.5VA

DC: Operational voltage range 24V ±10%

ripple 10% p-p max.; approx. 3W

Operating temperature: -10 to +55°C (14 to 131°F)

Operating humidity: 30 to 90% RH (non-condensing)

Mounting: Panel ﬂush mounting

Panel cutout: W92×H45 mm (3.62”×1.77”)

Panel thickness: 1.6 – 8.0 mm (0.06” – 0.31”)

Dimensions: W96×H48×D98.5 mm (3.78”×1.89”×3.88”)

Weight: 300 g (0.66 lbs)

PERFORMANCE in percentage of max. span

Accuracy

Display: ≤±1°C ±1 digit (PR, K, E, J, T)

≤±2°C ±1 digit (B, R, S, N)

Minimum display scale 1°C or 1°F (0.1°C for

K and J, narrow span)

Output: ≤±0.15% (DC output = display + output)

Cold junction compensation error:

±3°C maximum at 25 ±10°C

±5.4°F maximum at 77 ±18°F

Temp. coefcient: ≤±0.015%/°C (≤±0.008%/°F) when the

input range is set to the maximum span.

Input resolution: Max. 16 bits

Output resolution: Max. 13 bits

Response time: ≤0.5 second

(alarm output: 0 – 100% at 90% setpoint)

≤0.5 second (DC output: 0 – 90%)

Burnout response: ≤15 seconds

Line voltage effect: ±0.1% over voltage range

Insulation resistance: ≥100MΩ with 500V DC

Dielectric strength: 2000V AC @1 minute (input to DC

output to HH output or H output to L output

or LL output to power to ground)

INPUT & OUTPUT

■ THERMOCOUPLE

Input resistance: 1MΩ minimum

Burnout sensing: ≤0.1µA

■ DC OUTPUT

• DC Current

Operational range: -5 – +105%

Load resistance

(Range) 4 – 20mA : 550 (Ω maximum)

0 – 20mA : 550

• DC Voltage

Operational range: -5 – +105%

Load resistance

(Range) 0 – 10V : 10k (Ω minimum)

-10 – +10V : 10k

0 – 5V : 5000

1 – 5V : 5000

■ ALARM OUTPUT: Relay contact

Rated load: 250V AC @3A (cosø=1)

30V DC @3A (resistive load)

Electrical life ≥105cycles (rate 6 cycles/min.)

Maximum switching voltage: 250V AC, 30V DC

Maximum switching power: 750VA, 90W (resistive load)

Minimum load: 5V DC @10mA

Mechanical life: ≥5 ×106cycles (rate 180 cycles/min.)

Temperature Range

THERMOCOUPLE

CONFORMANCE

USABLE

RANGE RANGE

(PR) °C 0 to 1700 -30 to +1730

°F 32 to 3092 -22 to +3146

K(CA) °C -200 to +1300 -230 to +1330

°F -328 to +2372 -382 to +2426

K(CA), narrow span °C -100.0 to +450.0 -199.9 to +500.0

E(CRC) °C 0 to 600 -30 to +630

°F 32 to 1112 -22 to +1166

J(IC) °C -100 to +850 -130 to +880

°F -148 to +1562 -202 to +1616

J(IC), narrow span °C -100.0 to +350.0 -150.0 to +400.0

T(CC) °C -200 to +400 -230 to +430

°F -328 to +752 -382 to +806

B(RH) °C 400 to 1800 70 to 1830

°F 752 to 3272 158 to 3326

R °C 200 to 1700 -30 to +1730

°F 392 to 3092 -22 to +3146

S °C 0 to 1700 -30 to +1730

°F 32 to 3092 -22 to +3146

N °C -200 to +1300 -230 to +1330

°F -328 to +2372 -382 to +2426

47LT

P. 3 / 9ES-9512 Rev.1

FRONT PANEL CONFIGURATION

(4) Max/Min Button

(5) Alarm/ Button

(6) Init/ Button

(7) Shift Button

(8) Up Button

(1) Main Display

(2) Alarm Indicators

(3) Function Indicators

Alarm/ Init/Max/Min Shift Up

Ini

Alm D/P

Adj Fnc Min Max

• COMPONENT IDENTIFICATION

No. COMPONENT FUNCTION

(1) Main display Indicates present values, setting values.

(2) Alarm indicators Indicate alarm status of the input signal.

(3) Function indicators Indicate setting modes and status.

(4) Max/Min button Used to switch the main display to show present values, maximum values or minimum values.

(5) Alarm/ button Used to move on to the alarm setting mode; or to shift through setting items in each setting

mode.

(6) Init/ button Used to move on to the initial setting mode; or to shift through setting items in each setting

mode.

(7) Shift button Used to move on to the setting standby status and shift through display digits in each setting

item.

(8) Up button Used to change setting values.

Refer to the instruction manual for details on each function.

47LT

P. 4 / 9ES-9512 Rev.1

SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM

POWER

U(+)

V(–)

LOAD

Inductive

Load (Coil)

Varistor or

CR Circuit

• DC Powered

LOAD

Inductive

Load (Coil)

Diode, Varistor or

CR Circuit

■Relay Protection

• AC Powered

■ALARM SUFFIX CODE 1: N.O. contact, 4 points

POWER

U(+)

(

COM

)

(NC)

(NO)

(

COM

)

(NC)

(NO)

V(–)

■ALARM SUFFIX CODE 2: SPDT contact, 2 points

Lc, LLc

LLa

Hc, HHc

HHa

LL OUTPUT

L OUTPUT

H OUTPUT

L OUTPUT

H OUTPUT

HH OUTPUT

POWER

U(+)

V(–)

■ALARM SUFFIX CODE 0: No alarm output

Digital

Computation

Display /

Setting

A/D

Converter

–

T/C

comp. leadwire

–

CJC

SENSOR

metal leg

DC OUTPUT

–

Isolation

Output

Driver

Digital

Computation

Display /

Setting

A/D

Converter

–

T/C

comp. leadwire

–

CJC

SENSOR

metal leg

DC OUTPUT

–

Isolation

Output

Driver

Digital

Computation

Display /

Setting

A/D

Converter

–

T/C

comp. leadwire

–

CJC

SENSOR

metal leg

DC OUTPUT

–

Isolation

Output

Driver

*DO NOT loosen the screw of the terminal 3.

Loosen only the terminals 1 – 2 when connecting extension wires.

Note: The section enclosed by broken line is only with

DC output option.

47LT

P. 5 / 9ES-9512 Rev.1

SETTING PROCEDURE

POWER ON

Measuring Mode

Hold down Alarm/ or Init/ button

for ≥1 second

Hold down Init/ button

for ≥3 seconds

Measuring

■ GENERAL SETTING FLOWCHART

Measuring stopped*3

Mode transition

*1. Preset time can be specified with “Transition Time to Lockout Setting Mode” in Advanced Setting Mode.

*2. Alarm Setting Mode is locked with no-alarm-output type.

*3. The last measured values or status are held for DC and alarm outputs while the measuring is stopped.

(Except the analog output adjustments during the loop test and the initial setting)

*1. Optional settings for parameters in a broken-line section.

Alarm Setting Mode is locked with no-alarm-output type.

Scaling Setting Mode

Alarm Setting Mode

Advanced Setting Mode

Hold down Alarm/ or Init/

button for ≥1 second

Hold down Alarm/ or Init/ button

for ≥1 second

Hold down Max/Min + Alarm/ buttons at once

for a preset time duration*1

Hold down Alarm/ + Init/ buttons at once

for ≥3 seconds

POWER ON

■INITIAL SETTING FLOWCHART

Initial Setting Complete

Measuring Started

Hold down Init/ button for 3 seconds or more to move on to Initial Setting Mode.

Choose an input type and display range values.

Hold down Alarm/ button for 3 seconds or more to move on to Alarm Setting Mode.

Go through the alarm settings.

Hold down Alarm/ + Init/ buttons at once for 3 seconds or more

to move on to Advanced Setting Mode. Go through the advanced settings.

Hold down Alarm/ button or Init/ button for 1 second or more

to go back to Measuring Mode.

If necessary, hold down Max/Min button + Alarm/ buttons at once

for a preset time duration to enter Lockout Setting Mode.

Go through the lockout settings.

Lockout Setting Mode

Hold down Alarm/ or Init/ button

for ≥1 second

Hold down Alarm/ button

for ≥3 seconds

Loop Test Output Mode

Hold down Alarm/ or Init/ button

for ≥1 second

Hold down Alarm/ + Init/ + Shift buttons at once

for ≥5 seconds

47LT

P. 6 / 9ES-9512 Rev.1

PARAMETERS LIST

Refer to the instruction manual for details.

PARAMETER

Input type

Temperature unit

Input compensation

Input compensation: Offset temperature value is added at all measuring points. No gain setting.

Analog output 0% / 100%: 0% value < 100% value

Analog output 0% / 100% adjustment: Pressing [Shift] button switches the signal to increase or decrease, and then pressing [Up]

button controls it toward the desired output value. 0% value < 100% value

*1. °F indication is not available for K2 and J2 input type.

*2.

-199.9 to 999.9

for K2 and J2 input type

Temperature values must be re-set if the decimal point position is shifted due to an input

type change from K2/J2 to other types, or to K2/J2 from others.

Temperature input offset setting

°F

°C

INDICATORS FUNCTION DEFAULT

VALUE

DISPLAY

Ini

Ini Adj

...

Analog output 0% Temperature input for 0% output

Ini Adj Min

Ini Adj Max

Ini

Fnc

Adj

Ini

Fnc

Adj

...

Analog output 100% Temperature input for 100% output

Analog output 0%

adjustment

Analog output 0% adjustment:

adjustable range -5 to 105%

(increasing)

(decreasing)

(increasing)

(decreasing)

Min

Analog output 100%

adjustment

Analog output 100% adjustment:

adjustable range -5 to 105%

Max

J (IC), narrow span

J (IC)

K (CA), narrow span

K (CA)

E (CRC)

(PR)

T (CC)

B (RH)

■ INITIAL SETTING MODE : Hold down Init/ button for 3 seconds or more to enter Initial Setting Mode.

47LT

P. 7 / 9ES-9512 Rev.1

■ ALARM SETTING MODE : Hold down Alarm/ button for 3 seconds or more to enter Alarm Setting Mode.

PARAMETER

Alarm points

Quad alarm: LL, L, H, HH

Dual alarm: L, H

INDICATORS FUNCTION DEFAULT

VALUE

DISPLAY

LH Fnc

LHHH LL Fnc

...

LL setpoint

LL deadband (hysteresis)

LL ON delay time LL: ON delay time (seconds)

LL: Deadband (hysteresis) value

LL: Setpoint value

LL Fnc

LL trip action LL: Hi trip

LL Fnc

LL: Lo trip

LL coil at alarm LL: Coil energized at alarm

LL Fnc

LL: Coil de-energized at alarm

D/PLL Fnc

LLP Fnc

...

L setpoint

L deadband (hysteresis)

L ON delay time L: ON delay time (seconds)

L: Deadband (hysteresis) value

L: Setpoint value

L Fnc

L trip action L: Hi trip

L Fnc

L: Lo trip

L coil at alarm L: Coil energized at alarm

L Fnc

L: Coil de-energized at alarm

D/PL Fnc

LP Fnc

...

H setpoint

H deadband (hysteresis)

H ON delay time H: ON delay time (seconds)

H: Deadband (hysteresis) value

H: Setpoint value

H Fnc

H trip action H: Hi trip

H Fnc

H: Lo trip

H coil at alarm H: Coil energized at alarm

H Fnc

H: Coil de-energized at alarm

D/PH Fnc

HP Fnc

...

HH setpoint

HH deadband (hysteresis)

HH ON delay time HH: ON delay time (seconds)

HH: Deadband (hysteresis) value

HH: Setpoint value

HH Fnc

HH trip action HH: Hi trip

HH Fnc

HH: Lo trip

HH coil at alarm HH: Coil energized at alarm

HH Fnc

HH: Coil de-energized at alarm

D/PHH Fnc

HHP Fnc

Note 1: Alarm Setting Mode is locked with no-alarm-output type.

Alarm points depend upon the model suffix code. LL and HH setpoints are usable only for quad alarm type.

Note 2: LED status: = ON, = Blinking

Note 3: Alarm is disabled when ‘ – – – – ’ is specified for the setpoint.

Note 4: All alarm setpoints are disabled (reset to ‘ – – – – ’ status) when the input type has been changed. Re-setting is required.

*1. -199.9 to 999.9

for K2 and J2 input type

Main display flashing

at alarm Flashing in 1.0 sec. intervals

No flashing

Fnc

Flashing in 0.1 sec. intervals

Flashing in 0.2 sec. intervals

Flashing in 0.5 sec. intervals

47LT

P. 8 / 9ES-9512 Rev.1

■ ADVANCED SETTING MODE :

Hold down Alarm/ + Init/ buttons at once for 3 seconds or more to enter Advanced Setting Mode.

...

PARAMETER

Moving average

Brightness

Automatic return time to Measuring Mode

Automatic return time to Measuring Mode: The display goes back automatically to Measuring Mode if the front buttons are left untouched

for the specified time period while it is in one of the setting modes (except the loop test output mode).

With this value set to 0, the display must always be exited manually from the setting mode.

Transition time to Lockout Setting Mode: The display goes to Lockout Setting Mode only when the designated buttons are pressed for the

specified time duration.

CJC sensor: Specify either the cold junction compensation is enabled or not.

*1. Do not change the setting while in the burnout condition.

*2. F00.0 = 100 msec. refreshing rate

Specify in seconds

Brightness level 1 (dark)

Moving average with 8 samples

Moving average with 4 samples

Moving average with 2 samples

Brightness level 4

Brightness level 5 (bright)

Brightness level 3

Brightness level 2

No moving averaging

INDICATORS FUNCTION DEFAULT

VALUE

DISPLAY

Fnc

D/P Fnc

Transition time to Lockout Setting Mode

Specify in seconds

Fnc

Version indication Version number, indication onlyN/A N/A

Burnout *1Upscale burnout

Fnc

Downscale burnout

CJC sensor CJC sensor Disabled

Fnc

CJC sensor Enabled

...

Fnc Specify in secondsDisplay refreshing rate *2

■ LOCKOUT SETTING MODE :

Hold down Alarm/ + Max/Min buttons at once for a preset time duration to enter Lockout Setting Mode.

Alarm setting lockout

Lock Alarm Setting Mode

Unlock Alarm Setting Mode

D/P Fnc

Initial setting lockout

Advanced setting lockout Unlock Advanced Setting Mode

Lock Initial Setting Mode

Unlock Initial Setting Mode

D/P Fnc

Loop test output lockout

Lock Loop Test Output Mode

Unlock Loop Test Output Mode

Lock Advanced Setting Mode

Initialization

Execute Initialization

No initialization

PARAMETER INDICATORS FUNCTION DEFAULT

VALUE

DISPLAY

■ LOOP TEST OUTPUT MODE :

Hold down Alarm/ + Init/ + Shift buttons at once for 5 seconds or more to enter Loop Test Output Mode.

PARAMETER

Loopt test output: Pressing [Shift] button switches the signal to increase ( ON) or decrease ( ON), and then pressing [Up]

button controls it toward the desired output value.

*1. Temperature value can be specified within the usable range for the respective sensor types.

Decimal point position

for K2 and J2 input type:

-199.9 to 999.9

INDICATORS

FUNCTION DEFAULT

VALUE

DISPLAY

Adj Fnc

Min Max

...

Loop test output Temperature value for the loop test output

(display blinking)

Ini Alm D/P N/A

Max Min

47LT

P. 9 / 9ES-9512 Rev.1

EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)

MOUNTING REQUIREMENTS

96 (3.78)

48 (1.89)

103 (4.06)

95 (3.74)

2 (.08)

47 (1.85)

86 (3.39)12.5 (.49)

98.5 (3.88)

45 (1.77)

91.5 (3.60)

4–M3 SCREW

■REAR VIEW

• No Alarm Output • Alarm Output

■FRONT VIEW ■SIDE VIEW

■TOP VIEW

12345678910 12345678910

11 12 13 14 15 16 17 18 19 20

20–M3 SCREW

TERMINAL

2–M3 SCREW

10–M3 SCREW

TERMINAL

+ 0.8

– 0

+ 0.8

– 0

120 min.

75 min.

Panel thickness: 1.6 to 8.0 mm

■PANEL CUTOUT unit: mm

Autres manuels pour 47 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels M-system Instrument de mesure

M-system

M-system 47DV Manuel utilisateur

M-system

M-system 47 Series Manuel utilisateur

M-system

M-system 47D Series Manuel utilisateur

M-system

M-system 47LPT Manuel utilisateur

M-system

M-system R10-BS1 Manuel utilisateur

M-system

M-system 71VR1 Manuel utilisateur

M-system

M-system 47DM Manuel utilisateur

M-system

M-system 47 Series Manuel utilisateur

M-system

M-system TR30 Manuel utilisateur

M-system

M-system R1MS-GH3 Manuel utilisateur

M-system

M-system JB2 Manuel utilisateur

M-system

M-system 73VR3100 Guide de l'utilisateur

M-system

M-system 48NAVA Manuel utilisateur

M-system

M-system 47 Series Manuel utilisateur

M-system

M-system TR30 Manuel utilisateur

M-system

M-system R5-MS Manuel utilisateur

M-system

M-system 47LT Manuel utilisateur

M-system

M-system 47LM Manuel utilisateur

M-system

M-system 47LCT Manuel utilisateur

M-system

M-system 47 Series Manuel utilisateur

M-system

M-system 47NL Series Manuel utilisateur

M-system

M-system R1M-J3 Manuel utilisateur

M-system

M-system M Series Manuel utilisateur

M-system

M-system 43DV1-S Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur