M-system R30TS4 Manuel utilisateur

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9002 Rev.2 P. 1 / 5

INSTRUCTION MANUAL

THERMOCOUPLE INPUT MODULE

(4 points, isolated) MODEL R30TS4

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Thermocouple input module (body + CJC sensor × 4) ......(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■CONFORMITY WITH EU DIRECTIVES

• The equipment must be mounted inside the instrument

panel of a metal enclosure.

• The actual installation environments such as panel con-

ﬁgurations, connected devices, connected wires, may af-

fect the protection level of this unit when it is integrated

in a panel system. The user may have to review the CE

requirements in regard to the whole system and employ

additional protective measures to ensure the CE conform-

ity.

■GENERAL PRECAUTIONS

• Before you remove the terminal block or mount it, turn off

input signals for safety.

■HOT SWAPPABLE MODULES

• It is possible to replace a module with the power supplied

provided that the module is replaced with one with the

same model number and installed in the same base slot.

• Turn off input signals before replacing the module for

safety. Note that replacing multiple modules at once may

greatly change line voltage levels. We highly recommend

to replace them one by one.

■UNUSED CHANNEL

• Set unused channels to “CH disabled” with PC Conﬁgura-

tor software (model: R30CFG). Otherwise, unused chan-

nels left open are to be burnout status, setting a data er-

ror at the PLC or other host devices.

■ENVIRONMENT

• Indoor use.

• When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 10 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

• Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

• Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

• Be sure to attach the terminal cover for safety.

■AND ....

• The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

R30TS4

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9002 Rev.2 P. 2 / 5

COMPONENT IDENTIFICATION

RUN

ERR

RUN LED

Input Terminal Block

ERR LED

■FRONT VIEW

■BOTTOM VIEW

■SIDE VIEW

Lock Tab

Base Fixing Screw

Specifications

Positioning Guide

Terminal Cover

Terminal Fixing Screw

CJC Sensor (CJM x 4)

■STATUS INDICATOR LED

ID COLOR FUNCTION

RUN Green ON while network module operates normally

OFF in network module error

ERR Red OFF when input circuit and internal bus operate normally

Blinks in 1 sec. cycles when burnout is detected or with input value error (becomes less than the lower

limit or exceeds the upper limit of usable range).

Blinks in 400 msec. cycles with input circuit error (AD converter response failure).

ON with internal bus error

■TERMINAL ASSIGNMENTS

+CJ1

+CJ2

+CJ3

+CJ4

+IN1

COM1

+IN2

COM2

+IN3

COM3

+IN4

COM4

NO. ID FUNCTION NO. ID FUNCTION

1 +IN1 T/C 1 11 +CJ1 CJC 1

2 COM1 Common 1 12 NC No connection

3 +IN2 T/C 2 13 +CJ2 CJC 2

4 COM2 Common 2 14 NC No connection

5 NC No connection 15 NC No connection

6 +IN3 T/C 3 16 +CJ3 CJC 3

7 COM3 Common 3 17 NC No connection

8 +IN4 T/C 4 18 +CJ4 CJC 4

9 COM4 Common 4 19 NC No connection

10 NC No connection 20 NC No connection

R30TS4

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9002 Rev.2 P. 3 / 5

INSTALLATION

■INSTALLATION TO THE BASE

Use the Installation Base (model: R30BS).

The I/O slots are numbered in the ascending order starting

from the one on the immediate right side of the network

module (slot 1, slot 2...).

A code indicating the I/O slot number is assigned to each

I/O slot and I/O data is allocated in the order of this codes.

When an I/O slot is vacant, blank data is sent or received to/

from the PLC, etc.

PWR COM I/O1 I/O n

■HOW TO MOUNT THE MODULE

1) Engage the positioning guide of the module with the In-

stallation Base.

2) Pivot the module on the positioning guide and press it

down until the lock tab clicks into place.

Positioning Guide

3) Tighten the base ﬁxing screw using a screwdriver (stem

length: 70 mm/2.76” or more) (torque 0.5 N·m).

Base Fixing Screw

■HOW TO REMOVE THE MODULE

1) Loosen the base ﬁxing screw using a screwdriver (stem

length: 70 mm/2.76” or more).

Base Fixing Screw

2) While pressing the projection on the lock tab, push the

module upward.

3) Detach the positioning guide of the module from the In-

stallation Base.

Lock Tab

R30TS4

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9002 Rev.2 P. 4 / 5

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

For thermocouple input, attach the CJC sensor together with input wining to the input screw terminals.

■EXTERNAL DIMENSIONS unit: mm (inch)

110(4.33)

25(.98) 98(3.86)

20-M3

SCREW

(.24)

①

③

④

⑫

⑭⑤

⑥

⑦

⑧

⑨

⑩

⑮

⑲

⑳

RUN

ERR

⑰

②

■CONNECTION DIAGRAM

+IN1

COM1

+IN2

COM2

+CJ1

+CJ2

+IN3

COM3

+IN4

COM4

+CJ3

+CJ4

■INPUT CONNECTION EXAMPLE

+INn

+CJn

COMn

T/C

CJC

SENSOR

comp. leadwire

INPUT 1

INPUT 2

INPUT 3

INPUT 4

INTERNAL POWER

BUS CONNECTOR

INTERNAL BUS

R30TS4

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-9002 Rev.2 P. 5 / 5

WIRING INSTRUCTIONS

■TIGHTENING TORQUE

Separable screw terminal wiring screw: 0.5 N·m

Separable screw terminal ﬁxing screw: 0.5 N·m

■SOLDERLESS TERMINAL unit: mm (inch)

Refer to the drawing below for recommended ring tongue

terminal size. Spade tongue type is also applicable. Solder-

less terminals with insulation sleeve do not ﬁt.

Applicable wire size: 0.25 to 0.75 mm2

Recommended manufacturer: Japan Solderless Terminal

MFG. Co., Ltd., Nichifu Co., Ltd.

3.2 (.13) dia.

12 (.47) max.

6 max.

(.24)

3 (.12) max.

■HOW TO REMOVE SEPARABLE SCREW TERMINAL

The terminal block is separable in two pieces. Evenly loos-

en two screws on top and bottom of the terminal block to

separate.

■HOW TO ATTACH CJC SENSOR

In re-attaching once removed CJC sensor, connect it to ter-

minals +CJn and COMn as shown below.

A RTD is attached on the REAR surface of the CJC sensor.

In order to measure accurate reference junction tempera-

ture, be sure to connect the sensor to terminal COMn with

its upside FRONT surface.

+CJn COMn

CJC sensor

REAR surface

RTD

FRONT surface

PC CONFIGURATOR

The following parameter items can be set with using PC

Conﬁgurator Software (model: R30CFG).

Refer to the users manual for the R30CFG for detailed op-

eration of the software program.

■CHANNEL INDIVIDUAL SETTING

PARAMETER SETTING RANGE DEFAULT

SETTING

Unused setting CH enabled

CH disabled

CH enabled

Input Type K (CA)

E (CRC)

J (IC)

T (CC)

B (RH)

C (WRe 5-26)

P (Platinel II)

(PR)

K (CA)

Burnout Upscale

Downscale

None

Upscale

CJC Enabled

Disabled

Enabled

Unit degC

degF

degC

Fine zero adjustment

-320.00 – +320.00 (%)

0.00 (%)

Fine gain adjustment -3.2000 – +3.2000 1.0000

Zero base -3 200.0 – +3 200.0

(degC, K)

-32 000 – +32 000

(degF)

0.0

Full base -3 200.0 – +3 200.0

(degC, K)

-32 000 – +32 000

(degF)

0.0

Scaled range Zero -32 000 – +32 000 0

Scaled range Span -32 000 – +32 000 10 000

■CHANNEL BATCH SETTING

PARAMETER SETTING RANGE DEFAULT

SETTING

Conversion rate 250 ms

500 ms

Simulate input Normal input

Simulated data

Normal input

Table des matières

Autres manuels M-system Unité de contrôle

M-system

M-system R7F4HML3-D-DAC32B Manuel utilisateur

M-system

M-system R30US2 Manuel utilisateur

M-system

M-system M8YC Manuel utilisateur

M-system

M-system R7HL-DC16B Manuel utilisateur

M-system

M-system R3-SV8B Manuel utilisateur

M-system

M-system R3-NP1 Manuel utilisateur

M-system

M-system R7L-EC8B Manuel utilisateur

M-system

M-system R7ML-EA16 Manuel utilisateur

M-system

M-system M6SXF2 Manuel utilisateur

M-system

M-system Mini-M M2MNV Manuel utilisateur

M-system

M-system R3-GC1 Manuel utilisateur

M-system

M-system R3-ND1 Manuel utilisateur

M-system

M-system R7EWTU Manuel utilisateur

M-system

M-system R7HL-DAC15E Manuel utilisateur

M-system

M-system Mini-M M2ADS Manuel utilisateur

M-system

M-system 73VR3100 Manuel utilisateur

M-system

M-system R7ML-DC16B Manuel utilisateur

M-system

M-system EtherCAT R7I4DECT-1-PA8A Manuel utilisateur

M-system

M-system R7C-EC8A Manuel utilisateur

M-system

M-system EtherCAT R30GECT1 Manuel utilisateur

M-system

M-system R7ML-EC16D Manuel utilisateur

M-system

M-system R3-NEIP1 Manuel utilisateur

M-system

M-system R3-NL1 Manuel utilisateur

M-system

M-system R3-AR4 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur