M-system R3-PA4A Manuel utilisateur

R3-PA4A

P. 1 / 3 EM-8387 Rev.2

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

the contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Office or representatives.

■ PACKAGE INCLUDES:

Totalized pulse input module ..................................... (1)

■ MODEL NO.

Check that model No. described on the specification label is

exactly what you ordered.

■ INSTRUCTION MANUAL

This manual describes necessary points of caution when you

use this product, including installation, connection and basic

maintenance procedures.

INSTRUCTION MANUAL

MODEL R3-PA4A

HIGH SPEED TOTALIZED PULSE INPUT MODULE

(4 points, isolated)

POINTS OF CAUTION

■ HOT INSERTION/REMOVAL OF MODULES

Removing or replacing modules does not affect other modules

on the same backplane. It is possible to replace them without

removing the power supply. However, replacing multiple

modules at once may greatly change line voltage levels. We

recommend that you replace them one by one.

■ ENVIRONMENT

• Indoor use

• When heavy dust or metal particles are present in the air,

install the unit inside proper housing with sufficient ventila-

tion.

• Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH in

order to ensure adequate life span and operation.

■ WIRING

• Do not install cables (power supply, input and output) close

to noise sources (relay drive cable, high frequency line, etc.).

• Do not bind these cables together with those in which noises

are present. Do not install them in the same duct.

■ AND ....

• The unit is designed to function as soon as power is

supplied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data sheet.

INSTALLATION

Use the Installation Base (model: R3-BSx).

R3-PA4A

P. 2 / 3 EM-8387 Rev.2

COMPONENT IDENTIFICATION

■ DIMENSIONS mm (inch)

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

130 (5.12)

27.5 (1.08) 109 (4.29) POSITIONING

GUIDE

TERMINAL

COVER

20–M3

SCREW

6.2

(.24)

SW1SW2

SW3

■FRONT VIEW ■SIDE VIEW

ERR LED

RUN LED

Gain

Count Reset

Set the Count Reset SW to OFF to start counting.

■SIDE DIP SW

•Gain: SW3

SW GAIN INPUT

1 (*)2

SW3-1 OFF ON Input 1

SW3-2 OFF ON Input 2

SW3-3 OFF ON Input 3

SW3-4 OFF ON Input 4

(*) Factory setting

■STATUS INDICATOR LED

RUN indicator: Bi-color (red/green) LED;

Red when the bus A operates normally;

Green when the bus B operates normally;

Amber when both buses operate normally.

ERR indicator: Bi-color (red/green) LED;

Red with the excitation abnormality;

Green in normal operating conditions.

R3-PA4A

P. 3 / 3 EM-8387 Rev.2

■ CONNECTION DIAGRAM

M-SYSTEM WARRANTY

M-System warrants such new M-System product which it manufactures to be free from defects in materials and workmanship during the 36-month period following the date that such

productwasoriginallypurchasedifsuchproducthasbeenusedundernormaloperatingconditionsandproperlymaintained,M-System'ssoleliability,andpurchaser'sexclusiveremedies,

under this warranty are, at M-System's option, the repair, replacement or refund of the purchase price of any M-System product which is defective under the terms of this warranty. To

submit a claim under this warranty, the purchaser must return, at its expense, the defective M-System product to the below address together with a copy of its original sales invoice.

THIS IS THE ONLY WARRANTY APPLICABLE TO M-SYSTEM PRODUCT AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED

WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. M-SYSTEM SHALL HAVE NO LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR

SPECIAL DAMAGES OF ANY KIND WHATSOEVER.

M-System Co., Ltd., 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN, Phone: (06) 6659-8201, Fax: (06) 6659-8510, E-mail: [email protected]

WIRING INSTRUCTIONS

■SOLDERLESS TERMINAL mm (inch)

Refer to the drawing below for recommended ring tongue

terminal size. Spade tongue type is also applicable. Solderless

terminals with insulation sleeve do not fit. Applicable wire

size: 0.3 – 0.75 mm2

3.2 (.13) dia.

4 min.

(.16)

12 (.47) max.

6 max.

(.24)

3 (.12) max.

EXC +

INP TERM. 1

INP TERM. 2

INP TERM. 3

COM

INTERNAL POWER

BUS A

BUS B*

*For dual redundant communication.

BUS CONNECTOR

Input 1

EXC +

INP TERM. 1

INP TERM. 2

INP TERM. 3

COM

Input 2

EXC +

INP TERM. 1

INP TERM. 2

INP TERM. 3

COM

Input 3

EXC +

INP TERM. 1

INP TERM. 2

INP TERM. 3

COM

Input 4

■Input Connection Example (Input 1)

• Open Collector

12VDC

20kΩ

1kΩ7.5kΩ

Autres manuels M-system Unité de contrôle

M-system

M-system R7D-EC16B Manuel utilisateur

M-system

M-system R7M-MS4 Manuel utilisateur

M-system

M-system R3-NC3 Manuel utilisateur

M-system

M-system R7C-DC16A Manuel utilisateur

M-system

M-system R7M-EA16 Manuel utilisateur

M-system

M-system R7M-EC8B Manuel utilisateur

M-system

M-system R7D-YS2 Manuel utilisateur

M-system

M-system R7M-EC8A Manuel utilisateur

M-system

M-system R3-NF1 Manuel utilisateur

M-system

M-system R3-NEIP1 Manuel utilisateur

M-system

M-system F2DL Manuel utilisateur

M-system

M-system R3-NC2 Manuel utilisateur

M-system

M-system R7M-EC8C Manuel utilisateur

M-system

M-system R3-PA2 Manuel utilisateur

M-system

M-system M6NPS2 Manuel utilisateur

M-system

M-system R3-RS8 Manuel utilisateur

M-system

M-system R30YV4 Manuel utilisateur

M-system

M-system R8-DCM16ALH Manuel utilisateur

M-system

M-system M6SXF2 Manuel utilisateur

M-system

M-system R7HL-DC16A Manuel utilisateur

M-system

M-system R3-PT4 Manuel utilisateur

M-system

M-system R7C-YS2 Manuel utilisateur

M-system

M-system R7HL-DC8C Manuel utilisateur

M-system

M-system R5T-DA4 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur