Luxul AMS-4424P Manuel utilisateur

Simply Connected

Use the AMS-4424P to:

Optimize Streaming Media and HDMI

Over IP Performance

Offer Seamless Network Expansion

Up To 384 Ports

Connect up to 24 PoE-Enabled Devices

(Max Output 250 Watts)

Enhance Performance with Layer 2

and Layer 3 Functionality

Use the AMS-4424P to:

Quick Install Guide

AMS-4424P

AV Series 26-Port Gigabit Stackable

PoE+ L2/L3 Managed Switch

Quick Install Guide

AMS-4424P

14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450

LUX-QIG-AMS-4424P 036150505

Quick Install Guide

Model Number: AMS-4424P

AV Series 26-Port Gigabit Stackable PoE+ L2/L3 Managed Switch

No part of this publication may be modiﬁed or adapted in any way, for any

purposes without permission in writing from Luxul. The material in this manual

is subject to change without notice. Luxul reserves the right to make changes to

any product to improve reliability, function, or design. No license is granted, either

expressly or by implication or otherwise under any Luxul intellectual property rights.

An implied license only exists for equipment, circuits and subsystems contained in

this or any Luxul product.

DOCUMENT CONVENTIONS

These graphical alerts are used in this document to indicate notable situations:

NOTE: Tips, hints, or special requirements that you should take note of.

CAUTION: Care is required. Disregarding a caution can result in data

loss or equipment malfunction.

WARNING!: Indicates a condition or procedure that could result in

personal injury or equipment damage.

FCC COMPLIANCE

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

CONTACT LUXUL

Sales

P: 801-822-5450

E: [email protected]

Technical Support

P: 801-822-5450

E: suppor[email protected]

Simply Connected

Other trademarks and registered trademarks are the property of their respective owners

PACKAGE CONTENTS

The following items are included in the box:

26-Port Gigabit Stackable PoE+ L2/L3 Managed Switch

Power Cord

Rack Mount Kit

Four rubber pads

Quick Installation Guide

If any of the listed items are missing or damaged, please contact the Distributor

from whom you purchased for return/replacement.

HARDWARE DESCRIPTION

Front Panel

The front panel of the AMS-4424P Switch includes dual colored Link/Activity LEDs

that can be switched from green to blue. In addition, the front panel has Link/

Activity and PoE mode indicators as well as System and Power LEDs.

AMS-4424P Front Panel View

Rear Panel

The rear panel of the AMS-4424P Switch includes 1 console port, 24 Gigabit RJ45

Ports and

2 optical expansion ports that accommodate both 1 Gigabit SFP and 10

Gigabit SFP+ modules (for stacking)

, as well as LED indicators for each port. Each

Gigabit port has one Link/Activity/PoE LED. A push button switch with an LED

indicator switches the display between Link/Activity and PoE.

AMS-4424P Rear Panel View

Quick Install Guide

AMS-4424P

14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450

LUX-QIG-AMS-4424P 036150505

LED Indicators

Each port has one Link/Activity/PoE LED. A push button switch with LED indicator

switches the display between Link/Activity and PoE.

LED Indicators

LED indicators show the working status of the switch. The following table de-

scribes the LED functionality:

Indicator

Name

Description

System Green Flashing Indicates that the AMS-4424P is running normally.

Green On Booting up or indicates a malfunction. Contact

technical support.

Off Indicates that the AMS-4424P is in startup and initialization

process or is not on.

Power Green On This LED indicates that there is power to the AMS-4424P

Off If LED is off, check the power connection on the back of

the unit.

Speed/PoE

Button

Speed On Port LED’s display Speed status

PoE On Port LED’s display PoE status

Speed Green The Link/Activity LED of the port will be on if there is a

1000Mbps device connected to the port.

Yellow The Link/Activity LED of the port will be on if there is a

10/100Mbps device connected to the port.

Flashing The Link/Activity LED ﬂ ashes when a port is receiving

or transmitting data.

Off There is nothing connected to the port.

Simply Connected

Other trademarks and registered trademarks are the property of their respective owners

PoE On Connected device is receiving PoE Power.

Off Connected device is not receiving PoE power.

Green Power being supplied within PD Speciﬁed limits

Yellow Power exceeds PD Speciﬁed limits

Yellow

Flashing

PoE Fault( i.e. problem with Ethernet cable or PoE device).

At startup, port LEDs will ﬂash for 1 second as a self test.

Rear Panel

AMS-4424P Rear Panel View

Power Input: Please use the included power cable

PREPARING FOR INSTALLATION

System Requirements

 Ethernet Cables to connect the AMS-4424P to Ethernet enabled devices

Computer equipped with a Web browser. Supported Web browser versions

include Microsoft I.E. 9.0, Firefox 3.6, Safari 5.0, Chrome 6.0, Opera 10.6 and up.

The Web browser is used to conﬁgure the AMS-4424P.

 Power must be AC 100-240V~ 3.6A 50/60Hz.

Quick Install Guide

AMS-4424P

14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450

LUX-QIG-AMS-4424P 036150505

Before Connecting to the Network

The AMS-4424P can be rack-mounted or used as a desktop switch. Before connect-

ing to the network, please be aware of the following requirements:

Install the AMS-4424P in a stable/safe place to avoid any possible damage

Make sure there is space around the AMS-4424P for adequate ventilation and proper

heat dissipation. It is recommended to have at least 4-6 inches around all sides.

Do not place heavy articles on the AMS-4424P.

Power outlets should be within 5 feet of the AMS-4424P.

Verify the ground connection of the outlet is functioning properly.

Check the power cord to conﬁrm a secure connection.

Avoid placement in direct sunlight.

When installing the AMS-4424P on a ﬂat surface, attach the rubber feet to the

bottom of the device to avoid scratching the surface.

AMS-4424P INSTALLATION

Installing the AMS-4424P in a Rack

The AMS-4424P can easily be installed in a standard 19” rack. The AMS-4424P includes

two mounting ears for installing and stabilizing the switch. When attaching the

mounting ears and installing the switch within a rack, please refer to the following

illustration:

Simply Connected

Other trademarks and registered trademarks are the property of their respective owners

Rack-Mounting the AMS-4424P

 Using the included screws, attach the mounting ears to each side of the switch.

 Mount the switch in the rack with the LEDs facing outwards. Be sure the switch is

level and properly secured within the rack.

Desktop Setup

For use as a desktop device, position and apply the included rubber feet to the

bottom of the AMS-4424P.

Quick Install Guide

AMS-4424P

14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450

LUX-QIG-AMS-4424P 036150505

Attaching the Rubber Feet to the AMS-4424P

Network Connections:

The AMS-4424P supports 10/100/1000 Mbps Ethernet; 10/100 Mbps half/full-

duplex mode and 1000 Mbps full-duplex mode. All RJ-45 ports support Auto MDI/

MDIX and can be used as ordinary ports or as Uplink ports. Any RJ-45 port can be

used to connect the AMS-4424P to an Ethernet enabled device (including servers,

routers, and other switches) without a crossover cable.

For the RJ-45 ports, Category-5, super Category-5 or Category-6 unshielded twisted

pair (CAT5/CAT5e/CAT6 UTP) should be used.

NOTE: For best results, it is recommended that Category-6 shielded

twisted pair be used to ensure stable data transmission at 1000 Mbps.

The AMS-4424P also offers 2 optical expansion ports that accommodate both 1

Gigabit SFP and 10 Gigabit SFP+ modules (for stacking). Please see below for recom-

mended SFP module and cable options.

Stacking the AMS-4424P

The AMS-4424P support stacking of up to 16 Switches (total of 384 Ports) enabling

you to Manage the stacked Switches in one easy to use interface. Stacking in the

AMS-4424P is Enabled by default and requires an SFP+ (10Gbps) link to be con-

nected between Switches. When connecting more than two Switches there will

be a Master Switch that feeds the other Switches. Stacked Switches automatically

connect to the IP Address of the Master, facilitating Seamless management of the

entire Stack

Simply Connected

Other trademarks and registered trademarks are the property of their respective owners

NOTE: While the AMS-4424P support SFP and SFP+ Adapters only SFP+

Adapters will operate with the Stacking function of the Switch.

Standard SFP (1Gbps) Adapters will result in a normal

switched connection.

Stacking

Stacking the AMS-4424P

One Management Interface for the AMS-4424P

Quick Install Guide

AMS-4424P

14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450

LUX-QIG-AMS-4424P 036150505

SFP Cable

Due to the typical mounting proximity of Stacked Switches, Luxul recommends

using an SFP+ Copper Twinax Cable. SFP+ Fiber adapters can also be used and

Luxul recommends Multimode Fiber combined with Multimode capable Fiber

SFP+ adapters for Stacking Switches at distances greater than those supported by

Twinax Cables. Single Mode SFP+ Adapters can be used but must be selected to

conform to the Single Mode Fiber Lines used for interlink and due to the number

of possible options, Luxul has no standard recommendation. We recommend

contacting the Fiber Manufacturer for speciﬁcations to obtain the correct Single

Mode adapters requried. The Switch does support SFP Multi Mode and SFP Single

Mode adapters but will not take advantage of the Stacking function when these

modules are used.

Default IP Address

The AMS-4424P default IP address is 192.168.0.4. This address can be changed.

However, for hassle free installation of other plug and play Luxul devices, it is

recommended that the default IP value be maintained.

The AMS-4424P is not equipped with internal DHCP server. However, if your switch

is connected to a Luxul Router, conﬁguration will be automatic. Otherwise, the

IP address of the computer for login and conﬁguration will need to be manually

conﬁgured. The table below lists the default parameters of the AMS-4424P.

Parameter: Default Value

Default IP address: 192.168.0.4

Default user name: admin

Default password: admin

Autres manuels pour AMS-4424P

Table des matières

Autres manuels Luxul Changer

Luxul

Luxul Xen XGS-1008 Manuel utilisateur

Luxul

Luxul Xen XGS-1008 Manuel utilisateur

Luxul

Luxul XMS-1024P Manuel utilisateur

Luxul

Luxul XMS-1024P Manuel utilisateur

Luxul

Luxul XGS-1008P Manuel utilisateur

Luxul

Luxul XGS-1024S Manuel utilisateur

Luxul

Luxul XMS-1010P Manuel utilisateur

Luxul

Luxul AMS-1208P Manuel utilisateur

Luxul

Luxul XMS-1008P Manuel utilisateur

Luxul

Luxul XMS-1010P Manuel utilisateur

Luxul

Luxul XFS-1816P Manuel utilisateur

Luxul

Luxul Xen XGS-1008 Manuel utilisateur

Luxul

Luxul XGS-1024 Manuel utilisateur

Luxul

Luxul AMS-4424P Manuel utilisateur

Luxul

Luxul XMS-1008P Manuel utilisateur

Luxul

Luxul AMS-2616P Manuel utilisateur

Luxul

Luxul Xen XGS-1008 Manuel utilisateur

Luxul

Luxul XMS-1008P Manuel utilisateur

Luxul

Luxul XMS-7048P Manuel utilisateur

Luxul

Luxul AMS-1816P Manuel utilisateur

Luxul

Luxul AMS-2624P-E Manuel utilisateur

Luxul

Luxul AGS-1024 Manuel utilisateur

Luxul

Luxul XMS-5248P Manuel utilisateur

Luxul

Luxul XFS-1084P Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur