Luxul AMS-2616P Manuel utilisateur

Simply Connected

Use the AMS-2616P to:

 Add 802.3af/at PoE+ Capability to Your

AV Rack Solutions

Deliver Power and Data for up to

16 PoE-Enabled Network Devices at a

Maximum Output of 250 Watts

Simplify PoE Device Installation, Including

IP Security Cameras, VoIP Devices, and

Wireless APs

Optimize and Protect Your Network with

Advanced VLAN, QoS and Network

Security Features

Quick Install Guide

AMS-2616P

AV Series 26-Port Gigabit

Managed PoE+ Switch

Quick Install Guide

AMS-2616P

14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450

LUX-QIG-AMS-2616P-v2 026151104

Quick Install Guide

Model Number: AMS-2616P

AV Series 26-Port Gigabit Managed PoE+ Switch

No part of this publication may be modiﬁed or adapted in any way, for any

purposes without permission in writing from Luxul. The material in this manual

is subject to change without notice. Luxul reserves the right to make changes to

any product to improve reliability, function, or design. No license is granted, either

expressly or by implication or otherwise under any Luxul intellectual property rights.

An implied license only exists for equipment, circuits and subsystems contained in

this or any Luxul product.

DOCUMENT CONVENTIONS

These graphical alerts are used in this document to indicate notable situations:

NOTE: Tips, hints, or special requirements that you should take note of.

CAUTION: Care is required. Disregarding a caution can result in data

loss or equipment malfunction.

WARNING!: Indicates a condition or procedure that could result in

personal injury or equipment damage.

FCC COMPLIANCE

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

CONTACT LUXUL

Sales

P: 801-822-5450

E: [email protected]

Technical Support

P: 801-822-5450

E: suppor[email protected]

Simply Connected

Other trademarks and registered trademarks are the property of their respective owners

PACKAGE CONTENTS

The following items are included in the box:

AMS-2616P AV Series 26-Port Gigabit Managed PoE+ Switch

Power Cord

Rack Mount Brackets and Screws

Four Rubber Foot Pads

Quick Installation Guide

If any of the listed items are missing or damaged, please contact the Distributor

from whom you purchased for return/replacement.

HARDWARE DESCRIPTION

Front Panel

The front panel of the AMS-2616P Switch includes dual colored Link/Activity LEDs

that can be switched from green to blue. In addition, the front panel has Link/

Activity and PoE mode indicators as well as System and Power LEDs.

AMS-2616P Front Panel View

Rear Panel

The rear panel of the AMS-2616P Switch includes 1 console port, 24 1000Mbps

RJ45 and 2 RJ-45/SFP combo ports, as well as LED indicators for each port. Each

1000Mbps port has one Link/Activity/PoE LED. A mode/reset button switches the

display between Link/Activity and PoE modes.

AMS-2616P Rear Panel View

Power Input: Please use the included power cable

Quick Install Guide

AMS-2616P

14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450

LUX-QIG-AMS-2616P-v2 026151104

NOTE: Ports 1-8 are non PoE, ports 9-24 are PoE. All PoE Ports. are

enabled as PoE+ and low priority and Max power at 30W. This

results in a 480W allocation but with the management set to

“actual consumption” the PE units should power up until they hit

the 250W power budget limit.

LED Indicators

Each port has one Link/Activity/PoE LED. A mode/reset button on the rear panel

switches the LED display between Link/Activity and PoE modes.

LED Indicators

LED indicators show the working status of the switch. The following table de-

scribes the LED functionality:

Indicator

Name

Description

Front

Power On This LED indicates that there is power to the AMS-2616P

Off If LED is off, check the power connection on the back of the

unit

System Flashing Indicates that the AMS-2616P is running normally

On Indicates a malfunction. Contact technical support

Off Indicates that the AMS-2616P is in startup and initialization

process or is not on

Link Act/

PoE Mode

Link Activity Port LED’s display Link/Activity status

PoE Port LED’s display PoE status

Simply Connected

Other trademarks and registered trademarks are the property of their respective owners

The rear panel mode LEDs for Link Act/PoE mode are the same as the front

Port LEDS Link Activity

On The Link/Activity LED of the port will be on if there is a

device connected to the port

Flashing The Link/Activity LED ﬂ ashes when a port is receiving or

transmitting data

Off There is nothing connected to the port

PoE

On Connected device is receiving PoE power

Off Connected device is not receiving PoE power

Flashing PoE fault (i.e. problem with Ethernet cable or PoE device)

Rear

Speed/

Link/Act

Green The Link/Activity LED of the port will be on if there is a

1000Mbps device connected to the port

Amber The Link/Activity LED of the port will be on if there is a

10/100Mbps device connected to the port

Flashing The Link/Activity LED ﬂ ashes when a port is receiving

or transmitting data

Off There is nothing connected to the port

PoE On Connected device is receiving PoE Power

Off Connected device is not receiving PoE power

Green Power being supplied within PD Speciﬁ ed limits

Amber Power exceeds PD Speciﬁ ed limits

Amber Flashing PoE Fault( i.e. problem with Ethernet cable or PoE device)

Quick Install Guide

AMS-2616P

14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450

LUX-QIG-AMS-2616P-v2 026151104

PREPARING FOR INSTALLATION

System Requirements

 Ethernet Cables to connect the AMS-2616P to Ethernet enabled devices

Computer equipped with a Web browser. Supported Web browser versions

include Microsoft I.E. 9.0, Firefox 3.6, Safari 5.0, Chrome 6.0, Opera 10.6 and up.

The Web browser is used to conﬁgure the AMS-2616P.

 Power must be AC 100-240V~ 5.0A(Max) 50/60Hz.

Before Connecting to the Network

The AMS-2616P can be rack-mounted or used as a desktop switch. Before connect-

ing to the network, please be aware of the following requirements:

Install the AMS-2616P in a stable/safe place to avoid any possible damage

Make sure there is space around the AMS-2616P for adequate ventilation and proper

heat dissipation. It is recommended to have at least 4-6 inches around all sides.

Power outlets should be within 5 feet of the AMS-2616P.

Verify the ground connection of the outlet is functioning properly.

Check the power cord to conﬁrm a secure connection.

Avoid placement in direct sunlight.

When installing the AMS-2616P on a ﬂat surface, attach the rubber feet to the

bottom of the device to avoid scratching the surface.

Simply Connected

Other trademarks and registered trademarks are the property of their respective owners

AMS-2616P INSTALLATION

Installing the AMS-2616P in a Rack

The AMS-2616P can easily be installed in a standard 19” rack. The AMS-2616P includes

two mounting ears for installing and stabilizing the switch. When attaching the mount-

ing ears and installing the switch within a rack, please refer to the

following illustration:

Rack-Mounting the AMS-2616P

Quick Install Guide

AMS-2616P

14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450

LUX-QIG-AMS-2616P-v2 026151104

 Using the included screws, attach the mounting ears to each side of the switch.

 Mount the switch in the rack with the LEDs facing outwards. Be sure the switch is

level and properly secured within the rack.

Desktop Setup

For use as a desktop device, position and apply the included rubber feet to the

bottom of the AMS-2616P.

Attaching the Rubber Feet to the AMS-2616P

Simply Connected

Other trademarks and registered trademarks are the property of their respective owners

Network Connections:

The AMS-2616P supports 10/100/1000 Mbps Ethernet; 10/100 Mbps half/full-

duplex mode and 1000 Mbps full-duplex mode. All RJ-45 ports support Auto MDI/

MDIX and can be used as ordinary ports or as Uplink ports. Any RJ-45 port can be

used to connect the AMS-2616P to an Ethernet enabled device (including servers,

routers, and other switches) without a crossover cable.

The AMS-2616P offers 2 RJ-45/SFP combo ports for expansion. This allows for

the use of standard Ethernet cable or Gigabit optical ﬁber for network expansion.

If using optical ﬁber, Gigabit SFP modules are required (Not Included). Once the

Gigabit SFP optical modules are inserted, these interfaces can support optical ﬁber

cables to extend the Gigabit network—enabling the network to reach beyond the

300 foot limitation of twisted pair Ethernet.

For the RJ-45 ports, Category-5, super Category-5 or Category-6 unshielded twisted

pair (CAT5/CAT5e/CAT6 UTP) should be used.

NOTE: For best results, it is recommended that Category-6 shielded

twisted pair be used to ensure stable data transmission at 1000 Mbps.

Optical ﬁber/cable should be selected based on the wavelength of the SFP

optical module to be used.

Make sure only one Uplink channel exists between switches or between the AMS-

2616P and a router. Otherwise, loops can occur and result in network failure.

Quick Install Guide

AMS-2616P

14203 Minuteman Drive, Suite 201, Draper, UT 84020-1685 | luxul.com | 801-822-5450

LUX-QIG-AMS-2616P-v2 026151104

Default IP Address

The AMS-2616P default IP address is 192.168.0.4. This address can be changed.

However, for hassle free installation of other plug and play Luxul devices, it is

recommended that the default IP value be maintained.

The AMS-2616P is not equipped with internal DHCP server. However, if your switch

is connected to a Luxul Router, conﬁguration will be automatic. Otherwise, the

IP address of the computer for login and conﬁguration will need to be manually

conﬁgured. The table below lists the default parameters of the AMS-2616P.

Parameter: Default Value

Default IP address: 192.168.0.4

Default user name: admin

Default password: admin

1. Plug an Ethernet cable into any of the ports of the switch

2. Plug the other end into the Ethernet port of your computer

3. Power on the switch

4. Check to see that the IP address of the computer is within this network

segment: 192.168.0.xxx (“xxx” ranges 1~254). For example, 192.168.0.100.

5. Open the Web browser, and enter 192.168.0.4. The login window appears.

6. Enter the user name and password (default user name and default password

are both set as “admin”), and then click “OK” to login to the switch

conﬁguration window.

Table des matières

Autres manuels Luxul Changer

Luxul

Luxul Xen XGS-1008 Manuel utilisateur

Luxul

Luxul XGS-1024 Manuel utilisateur

Luxul

Luxul XGS-1024 Manuel utilisateur

Luxul

Luxul XFS-1816P Manuel utilisateur

Luxul

Luxul AMS-1208P Manuel utilisateur

Luxul

Luxul XFS-1084P Manuel utilisateur

Luxul

Luxul AMS-4424P Manuel utilisateur

Luxul

Luxul XMS-1008P Manuel utilisateur

Luxul

Luxul XMS-2624P Manuel utilisateur

Luxul

Luxul Xen XGS-1008 Manuel utilisateur

Luxul

Luxul XGS-1005 Manuel utilisateur

Luxul

Luxul XFS-1816P Manuel utilisateur

Luxul

Luxul XMS-7048P Manuel utilisateur

Luxul

Luxul AMS-2624P-E Manuel utilisateur

Luxul

Luxul XGS-1008P Manuel utilisateur

Luxul

Luxul XVS-F5 Manuel utilisateur

Luxul

Luxul XMS-2624P Manuel utilisateur

Luxul

Luxul XFS-1084P Manuel utilisateur

Luxul

Luxul XMS-1010P-E Manuel utilisateur

Luxul

Luxul AMS-1208P Manuel utilisateur

Luxul

Luxul XMS-1024P Manuel utilisateur

Luxul

Luxul AGS-1024 Manuel utilisateur

Luxul

Luxul XGS-1024S Manuel utilisateur

Luxul

Luxul Xen XGS-1008 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur