LSIS XEC-DN32H/DC Manuel utilisateur

Programmable Logic Control

XGB Hardware(

IEC)

XEC-DN32

XEC-DN64

XEC-DP32

XEC-DP

64H

XEC-

DR32H

XEC-

DR64H

XEC-DN32H

/DC

XEC-DR32H

/D1

XEC-DR64H

/D1

XGT Series

Safety Instruction

Before using the product …

For your safety and effective operation, please read the safety instructions thoroughly before

using the product.

►Safety Instructions should always be observed in order to prevent accident or risk with the

safe and proper use the product.

►Instructions are separated into “Warning” and “Caution”, and the meaning of the terms is as

follows;

This symbol indicates the possibility of serious injury or death if

some applicable instruction is violated

This symbol indicates the possibility of slight injury or damage to

products if some applicable instruction is violated

►The marks displayed on the product and in the user’s manual have the

following meanings.

Be careful! Danger may be expected.

Be careful! Electric shock may occur.

►The user’s manual even after read shall be kept available and accessible to

any user of the product.

Warning

Caution

Safety Instruction

Safety Instructions when designing

Please, install protection circuit on the exterior of PLC to protect

the whole control system from any error in external power or PLC

module. Any abnormal output or operation may cause serious problem

in safety of the whole system.

- Install applicable protection unit on the exterior of PLC to protect

the system from physical

damage such as emergent stop switch,

protection circuit, the upper/lowest limit switch, forward/reverse

operation interlock circuit, etc.

- If any system error (watch-dog timer error, module installation error,

etc.) is detected during CPU operation in PLC, the whole output is

designed to be turned off and stopped for system safety. However,

in case CPU error if caused on output device itself such as relay or

TR can not be

detected, the output may be kept on, which may

cause serious problems. Thus, you are recommended to install an

addition circuit to monitor the output status.

Never connect the overload than rated to the output module nor

allow the output circuit to have a short circuit, which may cause a

fire.

Never let the external power of the output circuit be designed to

be On earlier than PLC power, which may cause abnormal output or

operation.

In case of

data exchange between computer or other external

equipment and PLC through communication or any operation of

PLC (e.g. operation mode change), please install interlock in the

sequence program to protect the system from any error. If not, it

may cause abnormal output or operation.

Warning

Safety Instruction

Safety Instructions when designing

I/O signal or communication line shall be wired at least 100mm

away from a high-voltage cable or power line.If not, it may cause

abnormal output or operation.

Caution

Use PLC only in the environment specified in PLC manual or

general standard of data sheet. If not, electric shock, fire, abnormal

operation of the product or flames may be caused.

Before installing the module, be sure PLC power is off. If not,

electric shock or damage on the product may be caused.

Be sure that each module of PLC is correctly secured. If the

product is installed loosely or incorrectly, abnormal operation, error or

dropping may be caused.

Be sure that I/O or extension connecter is correctly secured. If

not, electric shock, fire or abnormal operation may be caused.

If lots of vibration is expected in the installation environment,

don’t let PLC directly vibrated. Electric shock, fire or abnormal

operation may be caused.

Don’t let any metallic foreign materials inside the product, which

may cause electric shock, fire or abnormal operation..

Caution

Safety Instruction

Safety Instructions when wiring

Prior to wiring, be sure that power of PLC and external power is

turned off. If not, electric shock or

damage on the product may be

caused.

Before PLC system is pow

ered on, be sure that all the covers of

the terminal are securely closed. If not, electric shock may be caused

Warning



Let the wiring installed correctly after checking the voltage rated

of each product and the arrangement of terminals. If not, fire,

electric shock or abnormal operation may be caused.

Secure the screws of terminals tightly with specified torque when

wiring. If the screws of terminals get loose, short circuit, fire or abnormal

operation may be caused.

Surely use the ground wire of Class 3 for FG terminals, which is

exclusively used for PLC. If the terminals

not grounded correctly,

abnormal operation may be caused.

Don’t let any foreign materials such as wiring waste inside the

module while wiring, which may cause fire, damage on the product

or abnormal operation.

Caution

Safety Instruction

Safety Instructions for test-operation or repair

Safety Instructions for waste disposal

Don’t touch the terminal when powered. Electric shock or abnormal

operation may occur.

Prior to cleaning or tightening the terminal screws, let all the

external power off including PLC power. If not, electric shock or

abnormal operation may occur.

Don’t let the battery recharged, disassembled, heated, short or

soldered. Heat, explosion or ignition may cause injuries or fire.

Warning

Don’t remove PCB from the module case nor remodel the module.

Fire,electric shock or abnormal operation may occur.

Prior to installing or disassembling the module, let all the external

power off including PLC power. If not, electric shock or abnormal

operation may occur.

Keep any wireless installations or cell phone at least 30cm away

from PLC. If not, abnormal operation may be caused.

Caution



Product or battery waste shall be processed as industrial waste.

The waste may discharge toxic materials or explode itself.

Caution

Safety Instruction

Revision History

Version

Date Remark Chapter

V 1.0 2009.2 1. First Edition -

V 1.1 2009.6

1. Add detailed description on High Speed Counter

specification

Ch8.1.1

V 1.2 2009.10 1. Add DC power unit

Ch2.1, Ch2.2

Ch4.1, Ch4.3

Ch7.2.1, Ch7.2.2

Ch8.1.1, Ch8.1.2

Appendix2

V1.5 2010.10

1. Add new module

2. Error in consumption current calculation fixed

3. Error in Momentary power failure and watch dog

fixed

4. Error in program execution fixed

5. Error in memory unit fixed

6. Error in remote function fixed

7. RTC flag, setting method modified

8. Input speciation of main unit fixed

9. Contents related with XGI deleted

10. Voltage reference fixed

11. Contents related with STOP LED deleted

12. APM_SSSB modified

13. XEC-DP32H/DP64H added

Ch2.1, Ch2.2,

Ch2.3.1, Ch4.1

Ch4.3, Ch4.4

Ch5.1.2, Ch5.1.4

Ch5.2.2

Ch5.4.1

Ch6.4

Ch6.12

Ch7.2.1, Ch7.2.2

Ch10.2

Ch10.3

Ch.11

Appendix4

Ch4.1, Ch4.3

Ch7.3.4, Ch7.3.6

Appendix2

V1.6 2014.2

1. Domain Of Homepage Changed

2. Add XEC-DN32H/DC

Front/Back

Cover

Ch2.1, Ch2.2

Ch4.1, Ch4.3

Ch7.2.1, Ch7.3.3

Ch8.1.1

Appendix2

V1.7 2015.7

1. Address & phone number changed

2. Add new module

3. Vibration Specification modified

Back Cover

Ch2.1, Ch2.2,

Ch2.3.3, Ch2.3.4

Ch3.1

V1.8 2016.11

1. . Add new module

- XBE-DN32A Ch7

V 1.9 2020.06 LSIS to change its corporate name to

LS ELECTRIC

Entire

Revision History

About User's Manual

１

About User’s Manual

Thank you for purchasing PLC of LS ELECTRIC Co.,Ltd.

Before use, make sure to carefully read and understand the User’s Manual about the functions, performances,

installation and programming of the product you purchased in order for correct use and importantly, let the end user

and maintenance administrator to be provided with the User’s Manual.

The Use’s Manual describes the product. If necessary, you may refer to the following description and order

accordingly. In addition, you may connect our website(http://www.lselectric.co.kr/)and download the information as

a PDF file.

Relevant User’s Manual

Title Description No. of User

Manual

XG5000 User’s

Manual

(XGI/XGR/XEC)

It describes how to use XG5000 software especially about

online functions such as programming, printing, monitoring

and debugging by using XGB (IEC language)

10310000512

XGI/XGR/XEC Series

Instruction &

Programming

It describes how to use the instructions for programming

using XGB (IEC language) series.

10310000510

XGB Hardware

User’s Manual (IEC

language)

It describes how to use the specification of power/input

/output/expansion modules, system configuration and built-in

High-speed counter for XGB main unit.

10310000983

XGB Analog

User’s Manual

It describes how to use the specification of analog

input/analog output/temperature input module, system

configuration and built-in PID control for XGB main unit.

10310000920

XGB Position

User’s Manual

It describes how to use built-in positioning function for XGB

main unit.

10310000927

XGB Cnet I/F

User’s Manual

It describes how to use built-in communication function for

XGB main unit and external Cnet I/F module.

10310000816

XGB Fast Ethernet I/F

User’s Manual

It describes how to use XGB FEnet I/F module.

10310000873

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels LSIS Contrôleurs

LSIS

LSIS XBF-AD04A Manuel utilisateur

LSIS

LSIS S100 Series Manuel de programmation

LSIS

LSIS XGT Series Manuel utilisateur

LSIS

LSIS XGT Series Manuel utilisateur

LSIS

LSIS XGT Series Manuel utilisateur

LSIS

LSIS XDL-L7SA002X Manuel utilisateur

LSIS

LSIS XGT Series Manuel utilisateur

LSIS

LSIS XBC-DN32U Manuel utilisateur

LSIS

LSIS LSLV-S100 Series Manuel utilisateur

LSIS

LSIS XEC-DR32H Manuel utilisateur

LSIS

LSIS XGT Series Manuel utilisateur

LSIS

LSIS XGL-CH2A Manuel utilisateur

LSIS

LSIS sv-ip5a Manuel utilisateur

LSIS

LSIS Master-K K200S Manuel utilisateur

LSIS

LSIS XDL-L7NH Series Manuel utilisateur

LSIS

LSIS XBM-DN16S Manuel utilisateur

LSIS

LSIS XGT Series Manuel utilisateur

LSIS

LSIS XBC-DR20SU Manuel utilisateur

LSIS

LSIS XGT Series Manuel utilisateur

LSIS

LSIS XGT Series Manuel utilisateur

LSIS

LSIS MASTER-K200S Manuel du propriétaire

LSIS

LSIS XGT Series Manuel utilisateur

LSIS

LSIS XGT Series Manuel utilisateur

LSIS

LSIS XEC-DN32U Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur

3M MicroTouch EX113 Manuel utilisateur