LSIS XGT Series Manuel utilisateur

Right choice for ultimate yield

LSIS strives to maximize customers' profit in gratitude of choosing us for your partner.

Programmable Logic Controller

XGR CPU Module

User’s Manual



Read this manual carefully before

installing,

wiring, operating, servicing or

inspecting this equipment.



Keep this manual within easy reach for

quick reference.

XGT Series

http://www.lsis.com

CPU

Expansion drive

XGR-CPUH/F

XGR-CPUH/T

XGR-CPUH/S

XGR-DBST

XGR-DBSF(S)

XGR-DBSH(S)

XGR-DBDT

XGR-DBDF

XGR-DBDH

Safety Instructions

Before using the product …

For your safety and effective operation, please read the safety instructions

thoroughly before using the product.

►Safety Instructions should always be observed in order to prevent accident

or risk with the safe and proper use the product.

►Instructions are separated into “Warning” and “Caution”, and the meaning of

the terms is as follows;

WARNING indicates a potentially hazardous situation which,

if not avoided, could result in death or serious injury

CAUTION indicates a potentially hazardous situation which,

if not avoided, may result in minor or moderate injury.

It may also be used to alert against unsafe practices

►The marks displayed on the product and in the user’s manual have the

following meanings.

Be careful! Danger may be expected.

Be careful! Electric shock may occur.

►The user’s manual even after read shall be kept available and accessible to

any user of the product.

Warning

Caution

Safety Instructions

Safety Instructions when designing

Please, install protection circuit on the exterior of PLC to protect

the whole control system from any error in external power or PLC

module. Any abnormal output or operation may cause serious problem

in safety of the whole system.

- Install applicable protection unit on the exterior of PLC to protect

the system from physical

damage such as emergent stop switch,

protection circuit, the upper/lowest limit switch, forward/reverse

operation interlock circuit, etc.

- If any system error (watch-dog timer error, module installation error,

etc.) is detected during CPU operation in PLC, the whole output is

designed to be turned off and stopped for system safety. However,

in case CPU error if caused on output device itself such as relay or

TR can not be

detected, the output may be kept on, which may

cause serious problems. Thus, you are recommended to install an

addition circuit to monitor the output status.

Never connect the overload than rated to the output module nor

allow the output circuit to have a short circuit, which may cause a

fire.

Never let the external power of the output circuit be designed to

be On earlier than PLC power, which may cause abnormal output or

operation.



In case of data exchange between computer or other external

equipment and PLC through communication or any operation of

PLC (e.g. operation mode change), please install interlock in the

sequence program to protect the system from any error. If not, it

may cause abnormal output or operation.

Warning

Safety Instructions

Safety Instructions when designing

I/O signal or communication line shall be wired at least 100mm

away from a high-voltage cable or power line.If not, it may cause

abnormal output or operation.

Caution

Use PLC only in the environment specified in PLC manual or

general standard of data sheet. If not, electric shock, fire, abnormal

operation of the product or flames may be caused.

Before installing the module, be sure PLC power is off. If not,

electric shock or damage on the product may be caused.

Be sure that each module of PLC is correctly secured. If the

product is installed loosely or incorrectly, abnormal operation, error or

dropping may be caused.

Be sure that I/O or extension connecter is correctly secured. If

not, electric shock, fire or abnormal operation may be caused.

If lots of vibration is expected in the installation environment,

don’t let PLC directly vibrated. Electric shock, fire or abnormal

operation may be caused.

Don’t let any metallic foreign materials inside the product, which

may cause electric shock, fire or abnormal operation..

Caution

Safety Instructions

Safety Instructions when wiring

Prior to wiring, be sure that power of PLC and external power is

turned off. If not, electric shock or

damage on the product may be

caused.



Before PLC system is powered on, be sure that all the covers of

the terminal are securely closed. If not, electric shock may be caused

Warning



Let the wiring installed correctly after checking the voltage rated

of each product and the arrangement of terminals. If not, fire,

electric shock or abnormal operation may be caused.

Secure the screws of terminals tightly with specified torque when

wiring. If the screws of terminals get loose, short circuit, fire or abnormal

operation may be caused.

Surely use the ground wire of Class 3 for PE terminals, which is

exclusively used for PLC. If the terminals not grounded correctly,

abnormal operation may be caused.

Don’t let any foreign materials such as wiring waste inside the

module while wiring, which may cause fire, damage on the product

or abnormal operation.

Caution

Safety Instructions

Safety Instructions for test-operation or repair

Safety Instructions for waste disposal

Don’t touch the terminal when powered. Electric shock or abnormal

operation may occur.

Prior to cleaning or tightening the terminal screws, let all the

external power off including PLC power.

If not, electric shock or

abnormal operation may occur.

Don’t let the battery recharged, disassembled, heated, short or

soldered. Heat, explosion or ignition may cause injuries or fire.

Warning

Don’t remove PCB from the module case nor remodel the module.

Fire,electric shock or abnormal operation may occur.

Prior to installing or disassembling the module, let all the external

power off including PLC power. If not, electric shock or abnormal

operation may occur.

Keep any wireless installations or cell phone at least 30cm away

from PLC. If not, abnormal operation may be caused.

Caution



Product or battery waste shall be processed as industrial waste.

The waste may discharge toxic materials or explode itself.

Caution

Revision History

Version Data Main contents Revised location

V 1.0 ’08.6 First Edition -

V 1.1 ’08.7 1. Modifying contents

(2) How to configure redundancy system

(3) Performance specification

(4) ScanTime

(5) Program memory

(6)I/O module skip function

(7) Module changing wizard during RUN

(8) Performance specification

(9) Example of calculating consumption current/power

(10) Caution in handling

(11) Grounding

2.Adding contents

(1) XGR redundancy system configuration

(2) Remote I/O system

(3) Scan Time

(4) I/O module skip

3. Deleting contents

(1) Max install-able module number in specification

2-5

4-1,4-2

5-6,5-8

5-28

6-19,6-20

6-21

7-1,7-3

8-5

11-5

11-13

1-3

2-13

5-8

6-20

7-1

V 1.2 ’09.9 1. Modifying contents

(1) Performance specification

(2) redundancy parameter setting window

(3) Flag

4-2

5-2,CH6

A-6,A-11

V 1.3 ’09.9 1.Adding contents

(1) Contents on redundancy system communication

operation setting (ONE IP Solution)

2. modifying contents

(1) Product list (add new products)

-XGR-DC32, XGR-DMMA

-XGF-SOEA

-XGL-EIPT

6-18~20

2-1

2-3

2-4

Revision History

Version Data Main contents Revised location

V 1.4 ’09.12 1.Adding contents

(1) adding contents related to DC power

Ch8.1, Ch8.2, Ch8.3

V 1.5 ’10.03 1.Adding contents

(1) Contents on reset/D.Clear

(2) Contents on Cnet/FEnet module equipment

(3) Contents on redundancy parameter

(4)Warning flag

(5) Smart Link wiring diagram and Event input module

specifications

2. Modifying contents

(1) Contents on parameter setting window

(2) Contents on Fault mask setting

(3) Module replacement

4-6

2-7

5-8~9

App-8

9-24~25

5-4, 6-1, 6-14~15

6-20

6-23~24

V 1.6 ’10.10 1. Modifying contents

(1) Modifying contents

(2)Adding contents

(3)Adding modules

(4) Modifying contents on redundancy parameter

(5) Modifying contents on basic parameter

Ch3.1

Ch5.1.2

Ch5.1.4

Ch6.7.1

V 1.7 ’10.10 1. Modifying contents

(1) Overview

(2) System configuration

(3) Power module

(4) Base and expansion cable

Ch1.1

Ch2.1

Ch8.4.1

Ch101.1

V 1.8 ’10.10 1.Adding contents

(1)Adding contents on redundancy parameter

(2)Adding contents on redundancy parameter

(3)Adding contents on redundancy parameter

Ch5.1.4

Ch6.8.1

Ch6.9

Revision History

Version Data Main contents Revised location

V 1.9 ’11.06 1.Adding contents

(1)Adding module on Extension redundancy

(2)Adding contents on Extension redundancy

(3) Adding contents on Flag

(4)Adding optical single module

1-1, 2-1, 7-2

1-3, 1-4, 2-8, 6-25,

8-3, 10-2, 14-28

App-3/7/11/13

1-1, 2-1, 2-6, 4-1, 4-2, 7-1

V 2.0 ’13.01 1.Adding contents

(1)Adding Redundancy Expansion Base

(2) Built-in PID Function

2.Modifying contents

(1) Modifying EtherNet/IP

(2) Modifying U,KDevice memory

3. Removing contents

(1) Removing Appendix 1.11

2-1, 10-1

Ch 14

1-6,2-7,2-13

4-1, 5-32

App-21

V 2.1 ’14.06 1.Adding contents

(1)Adding _REFRESH_NG_BASE

App-13

V 2.2 ’15.07 1.Modifying contents

(1) Vibration resistance Specifications

3-1

V 2.3 ‘15.09

1.Modifying contents

(1) Rated input voltage modified

(2) Circuit configuration modified

(3) Smart Link Model name modified

(4) Terminology modified (FG PE)

(5) CPU Processing Speed Unit changed (us ns)

(6) List of Configuration Products updated

8-1

9-2, 9-3, 9-4, 9-5

9-6

8-2, 10-1, 10-2, 11-2, 13-1

4.1

2.1

V 2.4 ‘16.03 1.Modifying contents

(1) Smart Link manual supplemented

9-6

※The number of User’s manual is indicated right part of the back cover.

About User’s Manual

Thank you for purchasing PLC of LSIS Co., Ltd.

Before use, make sure to carefully read and understand the User’s Manual about the functions,

performances, installation and programming of the product you purchased in order for correct

use and importantly, let the end user and maintenance administrator to be provided with the

User’s Manual.

The User’s Manual describes the product. If necessary, you may refer to the following

description and order accordingly. In addition, you may connect our website(http://eng.lsis.biz/)

and download the information as a PDF file.

Relevant User’s Manuals

Title Description No. of User’s

Manual

XG5000 User’s

Manual

(for XGI/XGR)

It describes how to use XG5000 software, which it is

applied to the IEC standard language, especially about

online functions such as programming, printing,

monitoring and debugging by using XGI/XGR series

products.

10310000834

XGI / XGR Series

Instructions &

Programming

It is the user’s manual for programming to explain how

to use commands that are used PLC system with XGI

CPU and XGR CPU.

10310000833

XGI-CPU User’s

Manual

It describes CPU specifications and technical terms for

the XGT PLC system using a series of XGI-CPU. 10310000832

Autres manuels pour XGT Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels LSIS Contrôleurs

LSIS

LSIS XGT Series Manuel utilisateur

LSIS

LSIS XP10BKA/DC Manuel utilisateur

LSIS

LSIS XEC-DN32H/DC Manuel utilisateur

LSIS

LSIS Master-K K200S Manuel utilisateur

LSIS

LSIS XBC-DR20SU Manuel utilisateur

LSIS

LSIS sv-ip5a Manuel utilisateur

LSIS

LSIS SV-iS7 series Manuel utilisateur

LSIS

LSIS XGT Series Manuel utilisateur

LSIS

LSIS S100 Series Manuel de programmation

LSIS

LSIS XGT Series Manuel utilisateur

LSIS

LSIS XGT Series Manuel utilisateur

LSIS

LSIS MASTER-K200S Manuel du propriétaire

LSIS

LSIS XDL-L7NH Series Manuel utilisateur

LSIS

LSIS XBC-DN32U Manuel utilisateur

LSIS

LSIS LSLV-S100 Series Manuel utilisateur

LSIS

LSIS XGL-CH2A Manuel utilisateur

LSIS

LSIS XGL-EFMT Manuel utilisateur

LSIS

LSIS XGT Series Manuel utilisateur

LSIS

LSIS XGT Series Manuel utilisateur

LSIS

LSIS XGT Series Manuel utilisateur

LSIS

LSIS XGT Series Manuel utilisateur

LSIS

LSIS XEC-DN32U Manuel utilisateur

LSIS

LSIS XGT Series Manuel utilisateur

LSIS

LSIS XGT Series Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur

3M MicroTouch EX113 Manuel utilisateur