LS ELECTRIC XGT Series Manuel utilisateur

LS ELECTRIC strives to maximize your profits in gratitude for choosing us as your partner.

Programmable Logic Control

XGT Ethernet Module

XGL-EFMTB

XGL-EFMFB

XGL-EFMHB

XOL-ES4T

XOL-ES4H

XGL-EH5T

XGL-EFMT

XGL-EFMF

XGT Series

Safety Instruction

Before using the product …

Foryoursafetyandeffective operation,pleaseread the safetyinstructionsthoroughlybeforeusingtheproduct.

SafetyInstructionsshould always beobserved inorderto preventaccidentorrisk withthesafeandproperuse

theproduct.

Instructionsare dividedinto“Warning”and “Caution”, and the meaningof the terms is asfollows.

This symbol indicates the possibility of serious injury or death if some applicable

instruction is violated

This symbol indicates the possibility of severe or slight injury, and property

damagesifsomeapplicable instructionisviolated

Moreover, even classified events under its caution category may develop into serious accidents relying

on situations.Thereforewe strongly advise users to observe all precautions properly just like warnings.

The marks displayed on the product and in the user’s manual have the followingmeanings.

Be careful! Dangermaybe expected.

Be careful! Electricshockmayoccur.

The user’s manual even after read shallbe keptavailableand accessible to any user of the product.

Warning

Caution

Safety Instruction

Safety Instructions for design process

1. Please install a protection circuit on the exterior of PLC so that the whole system may

operate safely regardless of failures from external power or PLC. Any abnormal output or

operation from PLC maycauseserious problems to safety in whole system.

- Install protection units on the exterior of PLC like an interlock circuit that deals with opposite

operations such as emergency stop,protection circuit, and forward/reverse rotation or install an

interlockcircuit that dealswith high/lowlimitunder itspositioncontrols.

- If any system error (watch-dog timer error, module installation error, etc.) is detected during

CPU operation in PLC, all output signals are designed to be turned off and stopped for safety.

However, there are cases when outputsignals remain active dueto device failures in Relayand

TR which can’t be detected. Thus, you are recommended to install an addition circuit to monitor

theoutputstatusfor those critical outputswhich maycausesignificant problems.

2. Never overload more than rated current of output module nor allow to have a short circuit.

Overcurrentforalongperiodtimemaycause afire.

3. Never let the external power of the output circuit to be on earlier than PLC power, which may

cause accidentsfromabnormal output oroperation.

4. Please install interlock circuits in the sequence program for safe operations in the system

when exchange data with PLC or modify operation modes using a computer or other

external equipments Read specific instructions thoroughly when conducting control operations

with PLC.

Warning

Safety Instruction

Safety Instructions for design process

Safety Instructions on installation process

I/O signal or communication line shall be wired at least 100mm away from a high-voltage cable or

power line. Failtofollowthis instructionmaycausemalfunctionsfrom noise

Caution

1. Use PLC only in the environment specified in PLC manual or general standard of data

sheet. If not, electric shock, fire, abnormal operation of the product may be caused.

2. Before install or remove the module, be sure PLC power is off. If not, electric shock or

damageon the productmaybecaused.

3. Be sure that every module is securely attached after adding a module or an extension

connector. If the product is installed loosely or incorrectly, abnormal operation, error or dropping

may be caused. In addition, contact failures under poor cable installation will be causing

malfunctions aswell.

4. Be sure that screws get tighten securely under vibrating environments. Fail to do so will

put the product under direct vibrations which will cause electric shock, fire andabnormaloperation.

5. Do not come in contact with conducting parts in each module, which may cause electric

shock,malfunctionsorabnormal operation.

Caution

Safety Instruction

Safety Instructions for wiring process

1. Prior to wiring works, make sure that every power is turned off. If not, electric shock or

damageon theproductmaybecaused.

2. After wiring process is done, make sure that terminal covers are installed properly before

its use.Failtoinstallthecovermaycauseelectricshocks.

Warning

1. Check rated voltages and terminal arrangements in each product prior to its wiring

process. Applying incorrect voltages other than rated voltages and misarrangement among

terminalsmaycausefire ormalfunctions.

2. Secure terminal screws tightly applying with specified torque. If the screws get loose, short

circuit,fireor abnormal operation maybe caused. Securing screws too tightly will cause damages

to themoduleormalfunctions,short circuit, anddropping.

3. Be sure to earth to the ground using Class 3 wires for FG terminals which is exclusively

used for PLC. If the terminals not grounded correctly, abnormal operation or electric shock may

be caused.

4. Don’t let any foreign materials such as wiring waste inside the module while wiring,

which maycausefire,damageon theproductorabnormaloperation.

5. Make sure that pressed terminals get tighten following the specified torque. External

connector type shall be pressed or soldered using proper equipments.

Caution

Safety Instruction

Safety Instructions for test-operation and maintenance

1. Don’t touch the terminal when powered.Electric shockorabnormaloperation mayoccur.

2. Prior to cleaning or tightening the terminal screws, let all the external power off including

PLC power. If not, electric shock or abnormal operation may occur.

3. Don’t let the battery recharged, disassembled, heated, short or soldered. Heat, explosion or

ignition maycauseinjuries orfire.

Warning

1. Do not make modifications or disassemble each module. Fire, electric shock or abnormal

operation mayoccur.

2. Prior to installing or disassembling the module, let all the external power off including PLC

power. If not, electric shock or abnormal operation may occur.

3. Keep any wireless equipment such as walkie-talkie or cell phones at least 30cm away from

PLC. If not,abnormaloperation maybe caused.

4. When making a modification on programs or using run to modify functions under PLC

operations, read and comprehend all contents in the manual fully. Mismanagement will cause

damages to products and accidents.

5. Avoid any physical impact to the battery and prevent it from dropping as well. Damages to

battery may cause leakage from its fluid. When battery was dropped or exposed under strong

impact, never reuse the battery again. Moreover skilled workers are needed when exchanging

batteries.

Caution

Safety Instruction

Safety Instructions for waste disposal

Product or battery waste shall be processed as industrial waste. The waste may discharge

toxic materials orexplode itself.

Caution

Revision History

Version

Date

Remark

Page

V1.0

2005.03

FirstEdition

V1.1

2005.05

Addingthefunction description

V1.2

2005.09

AddingmoduledetachmentandhowtochangeSettingPLCtypeat

XG-PD

Addingappendix(CPUmemorydevice)

CH3.8

CH5.2

APPENDIX-

V1.3

2005.11

Fixingfigureandadding contents

V1.4

2005.11

Fixingfigureandcontents

V1.5

2008.07

1.Addingmodels

-addingXGI/XGRredundantsystem

-addingswitchmodule(XGL-EH5T)

2.Adding E-mailservice

3.Adding error code table

4.AddingCH11CompliancewithEMCSpecifications

5.Fixingheadquarter address

CH1.3.2

CH7.6

CH10.4

CH11

Back cover-

V1.6

2009.09

1. ModifyingOverview

2.AddingCPU

3.Addingcontents onstandardsetting(One IPSolution,DHCP)

CH1.2.1

CH1.3.2

CH5.3

V1.7

2011.05

1.Howtoenablelink throughflagadded

2.Write_NC,Send_NC”instructionadded

CH5.5.2

CH7.2.1

V1.8

2013.10

1.AddingCommunicationloadspecifications

2.ChangingModbusserver offsetarea

CH2.2.3

CH8.3.1

V1.9

2014.03

1.ChangingCommunicationloadspecifications

2.Addinginfo-U,iXP

3.AddingXGRHSLink

4.AddingXGTDedicatedCommunication’sHeader

5.AddingXGTDedicatedCommunication’s error Code

6.AddingHighPerformanceXGT

7.Changingerror code table

CH2.2.3

CH4

CH6.6~6.7

CH8.1.2

CH8

CH9.2.3

CH10.4

V2.0

2014.11

XG5000 V4.0UIUpdate

V2.1

2016.10

XGL-EFMTB,XGL-EFMFBcontentsadded

V2.2

2017.06

Adding RAPIEnetprotocolandCnetprotocol

V2.21

2017.09

Error code update

CH10.2.2

V2.30

2018.05

Adding OPCUAServerservice

CH12

V3.0

2020.02

AddingSmartextensionservice

Revision History

Version

Date

Remark

Page

V3.1

2020.06

1. Formatandcontentsmodificationaccordingtothechangeof

companyname(LSIS -> LSELECTRIC)

2.AddingRAPIEnet+autoscan

3.AddingSmartExtensionservicediagnosticvariables

ALL

CH3.6

CH4, CH9

About User’s Manual

Thank youforpurchasingPLC of LS ELECTRICCo.,Ltd.

Before use, make sure to carefully read and understand the User’s Manual about the functions, performances, installation and

programming of the product you purchased in order for correct use and importantly, let the end user and maintenance

administrator to be provided with the User’s Manual.

The User’s Manual describes the product. If necessary, you may refer to the following description and order accordingly. In

addition, youmayconnectourwebsite (http://www.lselectric.co.kr/)anddownloadtheinformationas aPDFfile.

RelevantUser’sManuals

Title

Description

XG5000User’s Manual

(forXGK,XGB)

XG5000softwareusermanualdescribingonlinefunctionsuchas

programming,print,monitoring,debuggingbyusing XGK, XGB

CPU

XG5000 User’s Manual

(forXGI,XGR)

XG5000softwareusermanualdescribingonlinefunctionsuch

asprogramming,print,monitoring,debuggingbyusingXGI,

XGRCPU

XGK/XGBInstructions&Programming

User’s Manual

User’smanualfor programming toexplain howto use

instructionsthatareused PLCsystem withXGK,XGBCPU.

XGI/XGR Instructions& Programming

User’s Manual

User’smanualfor programming toexplain howto use

instructionsthatareused PLCsystem withXGI,XGRCPU.

XGK CPU User’s Manual

XGK-CPUU/CPUH/CPUA/CPUS/CPUE/CPUSN/CPUHN/

CPUUNusermanualdescribingaboutXGKCPUmodule,

powermodule, base,IOmodule, specification of extension cable

andsystem configuration,EMCstandard

XGI CPU User’s Manual

XGI-CPUU/D,CPUU,CPUH,CPUS,CPUE,CPUUNusermanual

describingaboutXGICPUmodule,powermodule,base,IO

module, specificationofextensioncableandsystem

configuration,EMCstandard

XGR redundant series User’s

Manual

XGR-CPUH/F,CPUH/TusermanualdescribingaboutXGR

CPUmodule,powermodule,extensiondrive,base,IO module,

specificationofextensioncable andsystem configuration,EMC

standard

CommunicationdeviceUser’s Manual

User’s manual for programming to explain how to use Extension

driver, Smart I/O extention,SmartI/Oblock

Autres manuels pour XGT Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels LS ELECTRIC Unité de contrôle

LS ELECTRIC

LS ELECTRIC XGT Series Manuel utilisateur

LS ELECTRIC

LS ELECTRIC SV-iS7 Series Manuel utilisateur

LS ELECTRIC

LS ELECTRIC XGT Series Manuel utilisateur

LS ELECTRIC

LS ELECTRIC CANopen LSLV-G100 Series Manuel utilisateur

LS ELECTRIC

LS ELECTRIC S100 Manuel utilisateur

LS ELECTRIC

LS ELECTRIC XGT Series Manuel utilisateur

LS ELECTRIC

LS ELECTRIC CANopen LSLV-G100 Series Manuel utilisateur

LS ELECTRIC

LS ELECTRIC XGT Series Manuel utilisateur

LS ELECTRIC

LS ELECTRIC LSLV-S100 Series Manuel utilisateur

LS ELECTRIC

LS ELECTRIC XGT Series Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur