Lovibond Tintometer PCM Manuel utilisateur

www.lovibond.com

Power & Communications Module

Junction Box Manual

Lovibond®Water Testing

Tintometer®Group

Contents

• 1.0 Introduction....................................................4

• 2.0 Installation.....................................................6

Unpacking .........................................................6

Mounting ..........................................................6

High Voltage Installation ...............................................8

Low Voltage Installation ..............................................12

• 3.0 Operation ................................................................ 17

Power Indicator.....................................................17

24VDC Power Switch ................................................17

Analog Outputs ....................................................17

Relay Outputs ......................................................17

USB..............................................................17

Optional RS-485 MODBUS ............................................17

• 4.0 Maintenance ............................................................. 18

Fuse Replacement ...................................................18

Cleaning ..........................................................19

• 5.0 Replacement Parts........................................................ 20

• 6.0 Speciﬁcations............................................................. 20

• 7.0 Certiﬁcation .............................................................. 21

FCC Class A Notice ..................................................21

DOC Class A Notice - Avis DOC, Classe A .................................21

• 8.0 Troubleshooting .......................................................... 22

To Preserve, Protect and Improve the Quality of the Environment

Disposal of Electrical Equipment in the European Union

Because of the European Directive 2002/96/EC your electrical instrument must not be disposed of with normal

household waste!

Tintometer GmbH will dispose of your electrical instrument in a professional and environmentally responsible manner.

This service, excluding the cost of transportation is free of charge. This service only applies to electrical instruments

purchased after 13th August 2005. Send your electrical Tintometer instruments for disposal freight prepaid to your

supplier

4PCM_V1 07.2017

Introduction

1.0 Introduction

The Power & Communications Module (PCM) contains the high

voltage power supply, digital and analog communicated interfaces for

Tintometer Process Sensors. It provides 24VDC, as well as

connections for two (2) 0-20 / 4-20mA analog current outputs, three

(3) digital relay outputs, and one (1) optional RS-485 MODBUS

network.

A qualiﬁed electrician trained in the installation of electrical

equipment should read and understand this manual prior to working

with this component as potential lethal hazards are present.

The manufacture does not take responsibility for any issues caused by

use of the unit not in accordance with the instructions laid out in this

manual.

Preface

Do not exceed temperatures or time spans in any case.

All warning labels must NOT be removed and should be replaced if

they become damaged or faded.

Important Information

The PCM can be mounted to a panel or to a wall.

Notes on power connection

The PCM should be permanently connected to mains power.

See local building codes for permanently connecting equipment.

Safety instructions for operation

Never open the high voltage housing while the PCM is connected to

mains power. There is a danger of electric shock and other hazards.

The high voltage area may only be opened and serviced by qualiﬁed

professionals.

Ensure proper grounding of the metal bonding plate near the bottom

of the enclosure. It must be connected to GND for proper operation.

Cleaning

Use a damp cloth with a non ﬂammable, non corrosive detergent.

PCM_V1 07.2017

Introduction

ATTENTION! - Indicates that important information or speciﬁc instructions need to be strictly followed;

(Information or instructions that can be found in the manual).

For professional users in the European Union:

If you wish to discard electrical and electronic equipment (EEE), please contact your dealer or supplier for

further information.

For disposal in countries outside of the European Union:

This symbol is only valid in the European Union (EU). If you wish to discard this product please contact

your local authorities or dealer and ask for the correct method of disposal.

DANGER! - A risk of severe injury or death from ELECTRICAL shock.

DANGER! - A risk of CHEMICAL injury.

WARNING! - A risk of severe burn; HOT SURFACE.

WARNING! - A risk of severe injury; PROTECTIVE EYE WEAR required.

ATTENTION! - radio wave emissions.

Guide to Symbols

Labels attached to the instrument should be strictly observed to avoid personal injury or

damage to the instrument. Refer to this document 'Guide to Symbols' for information

regarding the nature of the danger or risk before taking any action where such label is

present.

Read all instructions before using the instrument.

DANGER

A hazard exists that will result in death or severe injury if not avoided.

WARNING

A hazard exists that may result in death or severe injury if not avoided.

CAUTION

A hazard exists that may result in minor or moderate injury.

NOTICE

Important information or speciﬁc instructions need to be strictly followed..

6PCM_V1 07.2017

Installation

2.0 Installation

Unpacking

Carefully inspect all items to ensure that every part on the list below is

present and no visible damage has occurred during transportation.

Store the packing material to return the unit for repair or other kinds

of transport.

The table below shows the parts included in the packing

Part List

Mounting

1. Remove the front cover from the PCM

2. Align the PCM on the wall or panel, and mark and drill 4

mounting holes

3. Install (4) M4 x 20 or similar mounting screws

Part Description Quantity

1 PCM 1

2 Instruction Manual 1

PCM_V1 07.2017

Figure 1: Mounting screw locations

Installation

Figure 2: Mounting and product dimensions

122mm

4.80in

152mm

5.98in

170mm

6.69in

140mm

5.51in

96mm

3.78in

Figure 1:

Mounting screw locations

8PCM_V1 07.2017

DANGER

DISCONNECT POWER BEFORE SERVICING! Only a qualiﬁed installation technician

should connect AC power to the PCM

1. Remove the red thumb screw, and connectors at position J3 and J9

2. Remove the low voltage circuit board and high voltage barrier

Installation

High Voltage Installation

NOTICE

A local disconnect mounted in a suitable and easily reached location must be included

in the installation of this equipment. The local disconnect must be marked as the

disconnecting device for this equipment.

NOTICE

This unit was tested with metallic conduit as per UL 61010-1 with a bending moment of

34Nm (300 lb-in) at a horizontal distance of 300mm (12"). Do not exceed this bending

moment

PCM_V1 07.2017

Figure 3: Red thumb screw, J3 and J9 locations

Figure 4: Remove high voltage barrier

Installation

10 PCM_V1 07.2017

3. Remove the appropriate hole plugs from the bonding plate. The two

near the back are intended for high voltage use.

4. Connect AC power to the connector labeled J1 (see Figure 5 for

power connector location). AC power and protective earth wires

must be 12 to 18 AWG. A local disconnect switch or circuit breaker

which meets local electrical code is also required on the AC power

input, and must be located near the PCM.

5. Connect Relay outputs to connectors labeled J2, J3, and J4. Note that

Normally Open (NO) and Normally Closed (NC) contacts are provided/

See Figure 6 for wiring information.

6. Reinstall the low voltage board, connectors at position J3 and J9, and

the red thumb screw

Installation

High Voltage Installation

DANGER

ELECTRIC SHOCK HAZARD. The barrier must stay in place except when a qualiﬁed

installation technician is connecting power or relay outputs

CAUTION

ENSURE PROPER GROUNDING. Connect metal bonding plate to protective earth

for proper operation

WARNING

Potential ﬁre hazard. The relay contacts are not fused and rated at 5A max. External

devices should have a current limiting device to keep the current below 5A.

Table des matières

Autres manuels Lovibond Unité de contrôle

Lovibond

Lovibond Tintometer PTV Series Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur