Longshine CRANE 1 Manuel utilisateur
1
Tech Manual
CRANE 1
Fanless Full Flat Touch Screen POS System
Version 1.0
© Copyright LONGSHINE 2023
2
Table of Contents
System Disassembly…………………………………………….….....................3
A Before You Start………………………………………………………….....3
B Remove all the Peripherals (MSR, Customer Display) from the POS
Unit.......................................................................................................4
C Disconnect the Devices from the I/O Ports…………………………….5
a. Unplug the cables from the POS Unit………….……………………....5
D Remove the HDD/SSD Drive from the POS Unit…………………….....6
E Detach the Panel Unit (with Main Board) from the Base Unit…….7-9
F Panel Unit (with Main Board Set)...................................................10-16
a. Remove the HDD/SSD Drive from the Modular Main Board Set….10
b. Disconnect the Touch Controller from the Main Board……….........11
c. Remove Main Board from the Panel Unit…………………………….12
d. Remove the RAM Module……………………………………………...13
e. Remove the Metal Bracket of Bottom I/O Port……………………….14
f. Detach the LCD Panel from the Front Bezel Set…………………….15
g. Detach the LCD Panel from the Metal Bracket………………………16
G Cable management.............................................................................17
H Assemble the second display............................................................18
3
System Disassembly
A Before You Start
To prevent injuries to the LCD Panel: Carefully place the POS terminal on
a flat, clean and stable surface (for example: a stable long table).
Prepare additional cushioned material (for example: a soft, clean blanket).
Terminate the application running in the POS system, and shut down the
operation system.
Turn-off the power of POS terminal and optional peripherals (for example:
Thermal Receipt Printer, Secondary LCD Display).
Disconnect all the devices or cables connected to the POS terminal.
Disconnect and remove the power adaptor from the POS terminal.
Unplug the power cables from the electrical outlet.
Note:
There are no serviceable parts or components in the POS system or
peripherals.DO NOT modify any parts of POS systems or use
non-qualified parts or peripherals.
Store the disconnect parts, cables, devices and screws in a secure
location for further use.
For maintenance or replacement, please consult the technical personnel
and contact the sales for purchasing the new peripherals and parts.
4
B Remove All the Peripherals (MSR, Customer display) from
the POS Unit
Please refer to the User Manual for the instructions of installation and
disconnection procedures.
Pos Unit with MSR
( )
Pos Unit with Customer Display
( )
Pos unit without optional peripherals
( )
Note:
Always store the detached parts in a secure location for further use.
5
C Disconnect the Devices from the I/O Ports
There are some of the optional peripherals or devices installed onto the pos system.
Please detach the peripherals/devices and store them in a secure location.
Note:
Please turn off the whole POS system and devices before unplugging the cables from
the I/O Ports.
a. Unplug the cables from the POS Unit.
1. Place the POS terminal onto a stable and flat location.
2. Lift up the whole POS Unit and examine the bottom I/O Ports of POS Unit.
3. Disconnect all of the connected cables on the bottom I/O Ports.
Bottom I/O Ports with power cable connected
Bottom I/O Ports without power cable connected.
Note:
Always store the detached parts in a secure location for further use.
6
D Remove the HDD/SSD Drive from POS Unit
1. Remove the Protective Cover.
2. Remove the Screws of the
Protective Cover.
3. Pull out the HDD Drive Module
HDD Drive Module
(The appearance of the HDD will
vary because of different batches
products)
7
E Detach the Panel Unit (with Main Board) from the Base Unit
1. Remove the Two Screws of the Back Cover
2. Lift the Back Cover
3. Disconnect the Cable in the Machine
4. Remove the power switch and SSD slot
8
power switch (Left) and power switch (right)
5. Remove the Four Screws of the Main board.
6. Remove the VAG interface with 6-point screws.
7. Remove the 3 Screws of the I/O Plate.
I/O PLATE
9
8. Remove the 6 Screws of the I/O Plate.
9. Touch monitor plate
10.LCD Screen
11.Back shell
10
F Back Cover Unit (with Main Board Set)
a. Remove the HDD Drive from the Modular Main Board Set
1. Use a screw driver to remove the 4 screws of the metal SSD Slot.
Back Cover with Main Board
Set
Loosen the Securing Screws
on the Metal HDD Slot
Metal HDD Slot
Table des matières
Autres manuels Longshine Terminal tactile
Longshine
Longshine GFT-150 Series Manuel utilisateur
Longshine
Longshine POS GT-150 Series Manuel utilisateur
Longshine
Longshine RDT-150F Series Manuel utilisateur
Longshine
Longshine RCT150 Manuel utilisateur
Longshine
Longshine 15IW Series Manuel utilisateur
Longshine
Longshine POS GFT-150 Series Manuel utilisateur
Longshine
Longshine COBRA15 Manuel utilisateur
Longshine
Longshine GFT-150 Series Manuel utilisateur
Longshine
Longshine COBRA15 Manuel utilisateur
Manuels Terminal tactile populaires d'autres marques
Wincor Nixdorf
Wincor Nixdorf iPOS plus Advanced Manuel utilisateur
Ingenico
Ingenico AXIUM EX4000 Manuel utilisateur
Heisei Electronics
Heisei Electronics Q-POS 815 Manuel utilisateur
Amano
Amano MTX-15 Manuel utilisateur
FLOWBIRD
FLOWBIRD CWT Compact Touch Manuel utilisateur
Demco
Demco SP7 Manuel utilisateur
