Lippert Components Tire Linc Manuel utilisateur
CCD-0003912
Powered by
Technology
Quick Start Guide
Alert Indicator
NOTE: The purpose of this Quick Start Guide is for a quick setup
of the Alert Indicator for the Tire Pressure and Temperature
Monitoring System. Refer to the complete Aftermarket Manual
https://support.lci1.com/tire-linc for additional information.
Pairing Alert Indicator to Repeater................. 2
Operation ........................................ 6
Quick Start Guide
2
Pairing Alert Indicator to Repeater
Fig.1
1. Pair the Alert Indicator
(Fig.1) to the Repeater by
pressing and releasing the
Alert Indicator button (Fig.1A).
A. The Indicator will power
up and its LED (Fig.1B) will
blink red once then blue
three times indicating the
Alert Indicator is NOT linked
to the repeater.
NOTE: After 10 seconds,
the Indicator will enter sleep
mode.
2. Link the Alert Indicator to
the Repeater by pressing and
holding the Pair Mode button
on the Repeater for at least
ve seconds until the Status
LED blinks rapidly.
3. Release the Repeater’s Pair
Mode button.
4. Press the Alert Indicator’s button
(Fig.1A) once to make sure the
indicator is awake.
5. Within 10 seconds of waking the
indicator, press and hold the Alert
Indicator button.
A
B
3
A. Continue to hold the Alert
Indicator button until its LED
and buzzer sounds.
I. One beep will sound off and
one green LED flash will be
emitted. Continue to hold
the button.
II. Two beeps will sound
off and the LED will blink
green twice. Continue to
hold the button.
III. After the Indicator beeps
three times, release the
button. The LED will blink
green three times.
B. The Alert Indicator’s LED
will briefly blink blue and emit
a happy tone, indicating it has
been linked to the Repeater.
6. The Alert Indicator is now
linked to the Repeater.
NOTE: The Repeater’s Status
LED will indicate green, yellow
or red to indicate certain
conditions (see Step 7). The
number of blinks of the LED,
regardless of color, also
indicates battery status (see
Step 8).
7. Wait for the Repeater’s
Status LED to turn o, then
press and release the Alert
Indicator’s button. The
indicator’s LED will ash as
follows:
• Green to indicate the Re-
peater is in range and mon-
itoring; tires within pressure
and temperature limits.
4
• Yellow if there is no connec-
tion or out of range of the Re-
peater; cannot detect tire status.
• Red to indicate a fault, either
high/low pressure or tempera-
ture is out of range; Indicator will
beep for 10 seconds when tire
issue is seen for the rst time.
LED will continue to blink red
until fault is corrected.
• Red followed by blue notes
Indicator is not linked to the
Repeater.
8. Battery status indicators are as
follows (regardless of LED color in
Step 7):
• 3 blinks - Good, full charge
• 2 blinks - Low, not full charge
• 1 blink - Critical, needs
charging
5
When Stem Sensors are under
pressure, data is transmitted to the
Repeater when tires are:
• moving/rotating, every one
minute;
• not moving/not rotating, every
15 minutes.
The Alert Indicator will
continually scan for tire events
from the Repeater when it is
plugged into a USB cable connect-
ed to a powered USB port. This
conguration is best because it
will be the most responsive to tire
events.
When not plugged into a powered
USB port, e.g., running on internal
battery, the Alert Indicator period-
ically scans for data sent to the
Repeater, when tires are:
• moving/rotating, every
minute;
• not moving/not rotating,
scanning time increments
in 1, 2, 4, 8 and 15 minutes
(maximum), with the Indica-
tor entering sleep between
scans.
The Alert Indicator is provided
to send simple audio and vi-
sual alerts of a tire pressure or
temperature event. No additional
programming of the Indicator is
required.
NOTE: The Repeater’s Status
LED will blink green, yellow or
red to indicate certain conditions.
The number of blinks of the LED,
Operation
6
regardless of color, also indicates
battery status.
Wait for the Repeater’s Status LED
to turn o, then press and release
the Alert Indicator’s button. The in-
dicator’s LED will ash as follows:
• Green to indicate the Repeat-
er is in range and monitoring;
tires within pressure and tem-
perature limits.
• Yellow if there is no connec-
tion or out of range of the Re-
peater; cannot detect tire status.
• Red to indicate a fault, either
high/low pressure or tempera-
ture is out of range; Indicator will
beep for 10 seconds when tire
issue is seen for the rst time.
LED will continue to blink red
until fault is corrected.
Deep Sleep Mode
To place the Alert Indicator into
deep sleep mode, hold the button
until hearing one beep and then
release it. The Alert Indicator will
emit a happy tone and shut o.
NOTE: The Alert Indicator can
only enter deep sleep if not
plugged in.
• Red followed by blue notes
Indicator is not linked to the
Repeater.
Battery status indicators are as
follows (regardless of LED color):
• 3 blinks - Good, full charge
• 2 blinks - Low, not full
charge
• 1 blink - Critical, needs
charging
7
Should you have any questions, please do not
hesitate to contact us at 574-537-8900 or by email at
customerservice@lci1.com. Self-help tips, technical
documents, product videos and a training class schedule
are available at lci1.com or by downloading the MyLCI app.
Contact
Lippert Components Incorporated
CCD-0003912
R ev : 0 6 .17. 2 0
Autres manuels pour Tire Linc
2
Table des matières
Autres manuels Lippert Components Instrument de mesure
Lippert Components
Lippert Components Tire Linc 2.0 Instructions d'installation
Lippert Components
Lippert Components Tire Linc Pressure Monitor 2.0 Manuel utilisateur
Lippert Components
Lippert Components Tire Linc 2020106863 Instructions d'installation
Lippert Components
Lippert Components Tire Linc Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur