Lippert Components A-Frame Coupler Instructions d'installation

lci1.com 574-537-8900 Rev:02.11.20

A-Frame Coupler

Installation and Owner’s Manual

(For Aftermarket Applications)

CCD-0001314

Table of Contents

Introduction ............................................ 1

Parts List ................................................ 1

Safety Information ..................................... 2

Resources Required ................................... 2

Preparation ............................................. 2

Procedure ............................................... 2

Lower Jack Plate Replacement ........................ 3

Cleanup ................................................. 4

A-Frame

Coupler

Installation and

Owner’s Manual

(For Aftermarket Applications)

Introduction

The purpose of this document is to replace an A-frame

coupler.

Additional information about this product can be obtained

from lci1.com /support or by using the myLCI app.

Replacement components can be ordered from https://

store.lci1.com / or by using the myLCI app. The myLCI

app is available for free on iTunes®for iPhone®and iPad®

and also on Google Play™for Android™users. iTunes®,

iPhone®, and iPad®are registered trademarks of Apple Inc.

Google Play™and Android™are trademarks of Google Inc.

Parts List

Part# Description Qty

135430 A-Frame Coupler 1

lci1.com 574-537-8900 Rev:02.11.20

A-Frame Coupler

Installation and Owner’s Manual

(For Aftermarket Applications)

CCD-0001314

Safety Information

Resources Required

• Welder

• Welding PPE (helmet, gloves, sleeves, etc.)

• Safety glasses

• Clamps

• 9/16” socket

Preparation

1. Support the trailer according to OEM recommendations.

2. Remove the footpad from the tongue jack.

3. Release the tongue jack from the coupler plate by

unfastening the three 3/8” bolts with the 9/16” socket.

NOTE: Red lines with black borders indicate where

welding is to occur. Orange lines indicate where material

is being removed, either by cutting, grinding or some other

method.

Fig.1

Fig.2

Procedure

1. Remove the coupler (Fig.1A) from the A-frame (Fig.2A)

by cutting the existing welds.

2. Grind down any rough edges after removing the

components. All areas should be smooth before continuing.

NOTE: When cutting o󰀨 the coupler, do not cut into the

A-frame. Make sure to leave enough material to be ground

down.

SUPPORT CHASSIS ACCORDING TO

MANUFACTURER’S RECOMMENDATIONS. FAILURE

TO PROPERLY SUPPORT CHASSIS COULD RESULT

IN DEATH, SERIOUS PERSONAL INJURY, SEVERE

PRODUCT OR PROPERTY DAMAGE.

lci1.com 574-537-8900 Rev:02.11.20

A-Frame Coupler

Installation and Owner’s Manual

(For Aftermarket Applications)

CCD-0001314

3. Weld the coupler (Fig.3A) back onto the A-frame (Fig.4).Lower Jack Plate Replacement

NOTE: If the lower jack plate (Fig.5A) is not damaged,

it is acceptable to keep the same lower jack plate.

NOTE: If the tongue jack does not line up with the lower

jack plate as instructed in Step 1, replace the lower jack

plate.

1. Place the tongue jack through the coupler and line

the tongue jack up with the lower jack plate.

2. Remove the lower jack plate (Fig.5A) from the

A-frame (Fig.5B) by cutting the existing welds.

3. Grind down any rough edges after removing the

components. All areas should be smooth before

continuing.

Fig.3

Fig.4 Fig.5

lci1.com 574-537-8900 Rev:02.11.20

A-Frame Coupler

Installation and Owner’s Manual

(For Aftermarket Applications)

CCD-0001314

Manual information may be distributed as a complete

document only, unless Lippert Components provides

explicit consent to distribute individual parts.

All manual information is subject to change without

notice. Revised editions will be available for free

download at lci1.com. Manual information is considered

factual until made obsolete by a revised version.

Please recycle all obsolete materials and contact

Lippert Components with concerns or questions.

Fig.7

Fig.6

4. Using the tongue jack as a guide (not shown for clarity),

insert the replacement lower jack plate onto the tongue

jack. Then position the lower jack plate onto the A-frame

(Fig.6).

5. Weld the replacement lower jack plate (Fig.7A) onto the

underside of the A-frame (Fig.7B).

NOTE: Take care to maintain a perfect right angle with

the tongue jack, so that the tongue jack does not angle

unnecessarily once the lower jack plate is mounted.

Cleanup

1. Inspect all welds once they have cooled. Make sure weld

surfaces are smooth. Clean up any that are necessary.

2. Verify the functionality of the new coupler after

installation is complete.

3. Touch up any blemished areas with black spray paint.

4. Re-install the tongue jack per the manufacturer’s instructions.

Ce manuel convient aux modèles suivants

Autres manuels Lippert Components Accessoires automobiles

Lippert Components

Lippert Components Solera Power Awning Manuel d'utilisation et d'entretien

Lippert Components

Lippert Components ground control 3.0 Mode d’emploi

Lippert Components

Lippert Components In-Wall Slide-Out Winnebago Mode d'emploi

Lippert Components

Lippert Components Tire Linc Manuel utilisateur

Lippert Components

Lippert Components OneControl Hotspot Manuel utilisateur

Lippert Components

Lippert Components Kwikee Manuel utilisateur

Lippert Components

Lippert Components SolidStep 3.0 Premium Step Manuel utilisateur

Lippert Components

Lippert Components Ground Control 3.0 Landing Gear Manuel utilisateur

Lippert Components

Lippert Components Curt Rota-Flex Pin Box Manuel utilisateur

Lippert Components

Lippert Components SolidStep XF Manuel utilisateur

Lippert Components

Lippert Components SolidStep Instructions d'installation

Lippert Components

Lippert Components Solera Manuel utilisateur

Lippert Components

Lippert Components Air Ride 155925 Instructions d'installation

Lippert Components

Lippert Components ground control 3.0 Manuel utilisateur

Lippert Components

Lippert Components Edge Manuel utilisateur

Lippert Components

Lippert Components Solera Instructions d'installation

Lippert Components

Lippert Components 432223 Manuel utilisateur

Lippert Components

Lippert Components ABOVE FLOOR SLIDEOUT SYSTEM Manuel utilisateur

Lippert Components

Lippert Components Jack-It Manuel utilisateur

Lippert Components

Lippert Components Solera Power Awning Manuel d'utilisation et d'entretien

Lippert Components

Lippert Components Solera Manuel utilisateur

Lippert Components

Lippert Components PSX1 Manuel d'utilisation et d'entretien

Lippert Components

Lippert Components Solera Slide Topper Manuel utilisateur

Lippert Components

Lippert Components X-Trek Manuel utilisateur

Manuels Accessoires automobiles populaires d'autres marques

James Baroud

James Baroud Odyssey Manuel utilisateur

Motorola

Motorola i50sx Manuel utilisateur

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manuel utilisateur

Feniex

Feniex T3 Manuel utilisateur

Renault

Renault 77 11 423 180 Manuel utilisateur

Kia

Kia E8300-4D000 Manuel utilisateur

Brink

Brink 756843 Manuel utilisateur

Whispbar

Whispbar K085W Manuel utilisateur

v.link

v.link CI-VL2-PC-HSD Manuel utilisateur

Viking

Viking Stack-Rack Guide de configuration rapide

Aries

Aries 203015 Manuel utilisateur

Choetech

Choetech AT0005 Manuel utilisateur

ZZ2

ZZ2 ZZAIR-PRO Manuel utilisateur

Holman

Holman 4A80L Manuel utilisateur

Thule

Thule 2075 Manuel utilisateur

Motorola

Motorola T325 Manuel utilisateur

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guide d'installation

DV8

DV8 FBJL-02 Manuel utilisateur