Linear Technology DC1123 Manuel utilisateur

DC1123A QUICK START GUIDE

DESCRIPTION

Demonstration circuit 1123 is a I

C Quad Synchro-

nous Step-Down DC/DC Regulators featuring the

LTC3562. The LTC3562 is a quad high efficiency

monolithic synchronous step-down regulator with

an I

C interface. Two regulators are externally ad-

justable and can have their feedback voltages pro-

grammed between 425mV and 800mV in 25mV

(Type A). The other two regulators are fixed output

regulators whose output voltages can be pro-

grammed between 600mV and 3.775V in 25mV

steps (Type B). All four regulators operate inde-

pendently and can be put into pulse skip, LDO,

Burst Mode operation or forced Burst Mode opera-

tion through I

C control. The Type A regulators

have separate RUN pins that can be enabled if I

control is unavailable.

The 2.85V to 5.5V input range makes the LTC-

3562 ideally suited for single Li-ion battery pow-

ered applications. At low output load conditions,

the regulators can be switched into LDO, Burst

Mode operation or forced Burst Mode operation,

extending battery life in portable systems. The qui-

escent current drops to under 100µA with all regu-

lators in LDO mode and under 0.1µA when all

regulators are shut down

Switching frequency is internally set to 2.25MHz,

allowing the use of small surface mount inductors

and capacitors. All regulators are internally com-

pensated.

The LTC3562 is offered in a low profile 3mm



3mm QFN package.

Design files for this circuit board are available.

Call the LTC factory.

, LTC, LTM, LT, Burst Mode, are registered trademarks of Linear Technology

Corporation.

All other trademarks are the property of their respective owners.

TABLE 1. Typical Specifications (25°C)

Input Voltage Range: V

2.85V to 5.5V (Subject to dropout)

P600A 0.96V to 1.82V, 600mA (Max)

P600B 1.20V to 3.775V, 600mA (Max)

P400A 0.80V to 1.51V, 400mA (Max)

P400B 0.60V to 3.775V, 400mA (Max)

OPERATING PRINCIPLES

The LTC3562 is a highly integrated power man-

agement IC that contains four I

C controllable,

monolithic, high efficiency step-down regulators.

Two regulators provide up to 600ma of output

current and the other two regulators produce up

to 400ma. All four regulators are 2.25MHz, con-

stant-frequency, current mode switching regula-

tors that can be independently controlled through

C. All regulators are internally compensated

DC1123

QUICK START GUIDE

LTC3562

C Quad Synchronous

Step

Down DC/DC Regulators

DC1123A QUICK START GUIDE

eliminating the need for external compensation

components.

The LTC3562 offers two different types of ad-

justable step-down regulators. The two Type A

regulators (R600A, R400A) can have the feed-

back voltage adjusted from 425mv to 800mv in

25mv increments. The two Type B regulators

(R600B, R400B) can have the output voltages

adjusted through I

C control from 600mv to

3.775V in 25mv increments.

QUICK START PROCEDURE

Using short twisted pair leads for any power

connections and with all loads and power sup-

plies off, refer to Figure 1 for the proper meas-

urement and equipment setup.

NOTE.

When measuring the input or output voltage ripple, care

must be taken to avoid a long ground lead on the oscilloscope

probe. Measure the input or output voltage ripple by touching the

probe tip directly across the VCC or VOUT and GND terminals. See

Figure 2 for proper scope probe technique.

Place jumpers and load settings in the following

positions:

JP1 (RUN600A)

= ON

JP2 (RUN400A)

= ON

Load 1

= Consant Current 50mA

Load 2

= Constant Current 50mA

Load 3

= Constant Current 50mA

Load 4

= Constant Current 50mA

Connect Power Supply PS1 to VIN terminals

and adjust to 4.5 Volts to the demo board, as

shown in Figure 1.

Verify that OUT600A (1.8V) and OUT400A

(1.5V) are operational with proper output volt-

ages.

Once the proper output voltages are estab-

lished, adjust the loads within the operating

range and observe the output voltage regula-

tion, ripple voltage, and efficiency.

Open the Quickstart Software as discribed in the

DC590 Quick Start Guide

Set Jumpers JP1 (RUN400A) and JP2

(RUN600A) to Off Position. Connect Ribbon ca-

ble from DC590 demo circuit to J2. The LTC

3562 demonstation software should pop-up

automatically when the cable is installed.

Using the LTC3562 software GUI. See Figure 3.

Set all modes to Burst mode, VOUT 600A to

1.82V, VOUT 600B to 3.3V, VOUT 400A to

1.51V and VOUT 400B to 1.2V. Set all loads to

50mA. Check Auto Update buttons. Click on

Enable All button.

Once the proper output voltages are estab-

lished, adjust the loads within the operating

range and observe the output voltage regula-

tion, ripple voltage, and efficiency.

Using the LTC3562 software GUI. Set all modes

to Pulse Skip mode, VOUT 600A to 1.82V,

VOUT 600B to 3.3V, VOUT 400A to 1.51V and

VOUT 400B to 1.2V. Set all loads to 50mA.

10.

Once the proper output voltages are estab-

lished, adjust the loads within the operating

range and observe the output voltage regula-

tion, ripple voltage, and efficiency.

11.

Using the LTC3562 software GUI. Set all mod-

es to Forced Burst mode, VOUT 600A to 1.82V,

VOUT 600B to 3.3V, VOUT 400A to 1.51V and

VOUT 400B to 1.2V. Set all loads to 50mA.

12.

Once the proper output voltages are estab-

lished, adjust the loads within the operating

range and observe the output voltage regula-

tion, ripple voltage, and efficiency

13.

Using the LTC3562 software GUI. Set all mod-

es to LDO mode, VOUT 600A to 1.82V, VOUT

600B to 3.3V, VOUT 400A to 1.51V and VOUT

400B to 1.2V. Set all loads to 50mA.

DC1123A QUICK START GUIDE

14.

Once the proper output voltages are estab-

lished, adjust the loads within the operating

range and observe the output voltage regula-

tion, ripple voltage, and efficiency

15.

Using the LTC3562 software GUI. Set all

modes to Burst mode, VOUT 600A to 1.82V,

VOUT 600B to 3.3V, VOUT 400A to 1.51V and

VOUT 400B to 1.2V. Set all loads to 50mA.

16.

Monitor POR600A pin while increasing Load1

until the signal on POR600A goes low. The volt-

age on P600A will be less than 92% of voltage

setting.

17.

Set Load1 and Load2 to 450mA. Set Load3

and Load4 to 300mA. Adjust PS1 over the oper-

ating range and observe line regulation.

APPLICATION INFORMATION

This demo circuit is designed to demonstrate

the full capability of the LTC3562 I

C Quad Syn-

chronous Step-Down DC-DC Regulator. Not all

components are required in all applications.

The critical circuit components are on the top of

the board near the IC and listed in the Required

Circuit Components section of the Bill of Materi-

als, in Figure 5.

The input capacitor network of C1 and R1 is

used to dampen source lead inductances that

commonly occur in laboratory setups with

twisted leads and a bench power supply. When

using a USB cable this input damping network

will likely not be required. Please note that the

in-circuit capacitance of the specified 10uF,

0805 ceramic capacitor for C1 and C2 is less

than 5uF each with VIN greater than 4.25 Volts.

For good transient response and stability the

output capacitor each buck regulator should re-

tain at least 4uF of capacitance over the operat-

ing temperature and voltage range.

The output inductors for the OUT600A and

OUT600B are the recommended values of

3.3uH while the OUT400A and OUT400B are

4.7uH.

Resistors R4 and R6 are to adjust the output

voltage seen on the OUT600A output while R3

and R4 will set the voltage on the OUT400A

output.

DC1123A QUICK START GUIDE

Figure 1.

Proper Measurement Equipment Setup

VIN

GND

Figure 2.

Measuring Input or Output Ripple

DC1123A QUICK START GUIDE

Figure 3.

Graphical User Interface

DC1123A QUICK START GUIDE

Figure 4.

Circuit Schematic

DC1123A QUICK START GUIDE

Item Qty

Reference - Des Part Description Manufacturer, Part #

REQUIRED CIRCUIT COMPONENTS:

1 1 C2 CAP, CHIP X5R, 10uF, 10V, 0805 Murata, GRM21BR61A106KE19

2 4 C4,C7,C8,C9 CAP, CHIP,X5R, 10uF, 6.3V, 0603 TDK, C1608X5R0J106M

3 2 C5,C6 CAP, CHIP, COG, 10pF, 50v, 0402 Murata, GRM1555C1H100JZ01D

4 2 L2,L4 INDUCTOR, 3.3uH, 0.120 Ohms, 1.0A TOKO, 1098AS-3R3M

5 2 L1,L3 INDUCTOR, 4.7uH, 0.155 Ohms, 0.88A TOKO, 1098AS-4R7M

6 1 R3 RES, 0402, 475K OHMS, 1%, 1/16w VISHAY, CRCW0402475KFKED

7 1 R4 RES, 0402, 634K OHMS, 1%, 1/16w VISHAY, CRCW402634KFKED

8 1 R5 RES, 0402, 536K OHMS, 1%, 1/16w VISHAY, CRCW402536KFKED

9 1 R6 RES, 0402, 499K OHMS, 1%, 1/16w VISHAY, CRCW0402499KFKED

10 2 R12,R13 RES, 0402, 3.3M OHMS, 5%, 1/16w VISHAY, CRCW04023M30JNED

11 1 U1 I

C QUAD SYNCHRONOUS STEP-DOWN

DC/DC REGULATOR LINEAR TECH, LTC3562EUD

ADDITIONAL DEMO BOARD CIRCUIT COMPONENTS:

1 2 C10,C11 CAP, CHIP, X5R, 0.1uF, 10V TDK, C1005X5R1A104K

2 1 C1 CAP, CHIP,X5R, 10uF, 10V TDK, C2012X5R0J106M

3 1 R7 RES, 0402, 0.0 Ohms, 1/16w VISHAY, CRCW04020000Z0ED

4 1 R2 RES, 0402, 100K Ohms, 5%, 1/16w VISHAY, CRCW0402100KJNED

5 4 R8,R9,R10,R11 RES, 0402, 5.1K OHMS, 5%, 1/16w VISHAY, CRCW04025K1JNED

6 1 R1 RES, 0402, 1 OHM, 5%, 1/16w VISHAY, CRCW04021R00JNED

7 1 U2 SERIAL EEPROM MICROCHIP, 24LC025-I/ST

HARDWARE FOR DEMO BOARD ONLY:

1 2 JP1,JP2 HEADER,3 PINS, 2mm SAMTEC, TMM-103-02-L-S

2 2 JP1,JP2 SHUNT, 2mm SAMTEC, 2SN-BK-G

3 1 J1 CONN, USB MINI-B TYCO, 1734035-2

4 1 J2 HEADER, 2X7 PIN, 0.079CC MOLEX/WALDEN, 87831-1420

5 10 E1,E5,E6,E7,E8,

E9,E15,E16,E17,

E18 TURRET, 0.09 DIA MILL-MAX, 2501-2

6 8 E2,E3,E4,E10,E11,

E12,E13,E14 TURRET, 0.061 DIA MILL-MAX, 2308-2

7 4 STAND-OFF, NYLON 0.25" tall (SNAP ON) KEYSTONE, 8831 (SNAP ON)

Figure 5.

Bill of Materials

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Analog Devices Inc.:

DC1123A

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Linear Technology Carte mère

Linear Technology

Linear Technology DC752A Guide de configuration rapide

Linear Technology

Linear Technology DC2048A Manuel utilisateur

Linear Technology

Linear Technology DC823B-A Guide de configuration rapide

Linear Technology

Linear Technology LTC6655 Guide de configuration rapide

Linear Technology

Linear Technology DC1649A Guide de configuration rapide

Linear Technology

Linear Technology DC1962C Guide de configuration rapide

Linear Technology

Linear Technology 2429A Guide de configuration rapide

Linear Technology

Linear Technology DC1339 Manuel utilisateur

Linear Technology

Linear Technology LTC5584 Manuel utilisateur

Linear Technology

Linear Technology DC1385A Guide de configuration rapide

Linear Technology

Linear Technology DC1948A Guide de configuration rapide

Linear Technology

Linear Technology DC2117A Guide de configuration rapide

Linear Technology

Linear Technology DC2565A Guide de configuration rapide

Linear Technology

Linear Technology DC1678A Guide de configuration rapide

Linear Technology

Linear Technology DC1160 Guide de configuration rapide

Linear Technology

Linear Technology DC2442A Manuel utilisateur

Linear Technology

Linear Technology DC1636A Guide de configuration rapide

Linear Technology

Linear Technology DC2222A Guide de configuration rapide

Linear Technology

Linear Technology DC1386B Manuel utilisateur

Linear Technology

Linear Technology DC1145B Guide de configuration rapide

Linear Technology

Linear Technology DC1737A Guide de configuration rapide

Linear Technology

Linear Technology DC1880A Guide de configuration rapide

Linear Technology

Linear Technology LTC5584 Manuel utilisateur

Linear Technology

Linear Technology Analog Devices DC2515B Guide de configuration rapide

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur