0507320020/061112/EStatiex400-MS EN - 3
PREFACE
Using this manual
This manual is intended to be used as a work of reference for
professional, well-trained and authorised users to be able to
safely install, use, maintain and repair the product mentioned
on the cover of this document.
Pictograms and symbols
The following pictograms and symbols are used in this
manual:
Suggestions and recommendations to simplify
carrying out tasks and actions.
CAUTION!
Procedures which, if not carried out with the
necessary caution, may damage the product, the
workshop or the environment.
WARNING
Procedures which, if not carried out with the
necessary caution, may damage the product or
cause serious personal injury.
WARNING
Firehazard!Neverusetheproductforltering
inammable,glowingorburningparticlesorsolids
orliquids.Neverusetheproductforltering
aggressive fumes (such as hydrochloric acid) or
sharp particles.
WARNING
Denotes risk of electric shock.
Service and technical support
Forinformationaboutspecicadjustments,maintenanceor
repair jobs which are not dealt with in this manual, please
contact the supplier of the product. Make sure you have the
followingspecicationsathand:
- product name
- serial number
Thesedatacanbefoundontheidenticationplate.
1 SAFETY
General
The manufacturer does not accept any liability for damage to
the product or personal injury caused by non-observance of
the safety instructions in this manual, or by negligence during
installation, use, maintenance and repair of the product
mentioned on the cover of this document and any
corresponding accessories.
Specicworkingconditionsorusedaccessoriesmayrequire
additional safety instructions. Immediately contact your
supplier if you detect a potential danger when using the
product.
The user of the product is always fully responsible for
observing the local safety instructions and regulations.
Observe all safety instructions and regulations which
apply to handling welding equipment.
User manual
- Everyone working on or with the product must be familiar
with the contents of this manual and must strictly observe
the instructions therein. The management should instruct the
personnel in accordance with the manual and observe all
instructions and directions given.
- Neverchangetheorderofthestepstoperform.
- Always keep the manual with the product.
Pictograms and instructions on the product
(if present)
- The pictograms, warnings and instructions attached to the
product are part of the safety features. They must not be
covered or removed and must be present and legible during
the entire life of the product.
- Immediately replace or repair damaged or illegible
pictograms, warnings and instructions.
Users
Theuseofthisproductisexclusivelyreservedtoauthorised,
well-trainedandqualiedusers.Temporarypersonneland
personnel in training can only use the product under
supervision and responsibility of skilled engineers.
Intended use1
Theproducthasbeendesignedexclusivelyforharmfulfumes
and gases which are released during the most common
welding processes, with the strict restriction that these fumes
andgasescanonlybesuppliedthroughoneextractionarm,
whileusingoneextractionfan(SF2400). Using the product
for other purposes is considered contrary to its intended use.
The manufacturer accepts no liability for any damage or injury
resulting from such use. The product has been built in
accordance with state-of-the-art standards and recognised
safety regulations. Only use the product in technically perfect
condition in accordance with its intended use and the
instructions laid down in the user manual.
Technical specications
Thespecicationsgiveninthismanualmustnotbealtered.
Safety features
- All safety features must be correctly mounted and can only
be removed for maintenance and repair jobs by skilled and
authorised service engineers.
- The product must not be used if the safety features are not
or only partly present, or defective.
- The safety features should be regularly checked for their
proper functioning, and if required, be immediately repaired.
Modications
Modicationof(partsof)theproductisnotallowed.
Use
WARNING
Firehazard!Neverusetheproductforltering
inammable,glowingorburningparticlesorsolids
orliquids.Neverusetheproductforltering
aggressive fumes (such as hydrochloric acid) or
sharp particles.
- Inspect the product and check it for damage. Verify the
functioning of the safety features.
- Check the working environment. Do not allow unauthorised
persons to enter the working environment.
- Use common sense. Stay alert and keep your attention to
your work. Do not use the product when your are tired or
undertheinuenceofdrugs,alcoholormedicine.
- Makesuretheroomisalwayssufcientlyventilated,this
appliesespeciallytoconnedspaces.
- Neverinstalltheproductinfrontofentrancesandexits
which must be used by emergency services.
- Makesurethattheworkshopcontainssufcientapproved
reextinguishers.
- Protect the product against water and humidity.
1. “Intendeduse”aslaiddowninEN-ISO12100istheuseforwhichthetechnical
productissuitedasspeciedbythemanufacturer-inclusiveofhisdirectionsin
the sales brochure. In case of doubt it is the use which can be deducted from
the construction, the model and the function of the technical product which is
considered normal use. Operating the machine within the limits of its intended
use also involves observing the instructions in the user manual.
