LIMIT 5100 Manuel utilisateur

Coating Thickness Gauge 5100

Language Contents

Language page

English ....................................................................2-3

Svenska..................................................................4-5

Norsk....................................................................... -7

Dansk......................................................................8-9

Suomi......................................................................10-11

Deutsch...................................................................12-13

Nederlands.............................................................14-15

Français..................................................................16-17

Italiano.....................................................................18-19

Español...................................................................20-21

Português...............................................................22-23

Ελληvikά .................................................................24-25

Polski.......................................................................26-27

Eesti.........................................................................28-29

LietuviŠkai...............................................................30-31

Latviski....................................................................32-33

Pycckий ..................................................................34-35

6

1

2

Coating Thickness Gauge Limit 5100.

General information

Limit 5100 measure thickness of coating. E.g. paint,

plastic, porcelain enamel, copper, zinc, aluminium,

chrome galvanizing layer on magnetic and non-

magnetic materials.

Specification

Range 0 – 1000 μm

Reading 0-100 μm 0,1 μm

100-1000 μm 1 μm

Accuracy + 2,5 μm or 1-3 %.

Battery 4 st 1,5 V AAA

Automatic off After 2 minuts

Operation

1. On or manuell OFF. Push the Ө-button.

The instrument will be auto-calibrate so always keep the

probe away from any metal for 3 seconds after power on.

2. Select magnetic or non-magnetic material with N/NF

button. The display indicate Fe for magnetic material or

NFe for non-magnetic material.

3. Select μm for reading in 1/1000 mm.

4. Place the probe on an layer to be measured. Read

the coating thickness on the display.

5. For next measurement lift the probe more than 10

mm and repeat the measurement.

English

3

English

Calibration

1. Place the probe on an uncoated area.

2. Push the ZERO button.

3. Lift the probe.

4. Select a calibration foil according to your

measurement range. Measure the calibration foil on the

uncoated area.

5. Lift the probe and adjust with the ▲▼buttons the

value on the display to same value as foil.

6. Repeat the test measurement and adjust the value

until the result is correct.

It is recommended that calibration is made on same

material as to be measured.

Replace battery

When battery symbol shows on the display.

Remove the battery lid on backside and replace with 4

pcs 1,5 V batterys type AAA.

Table des matières

Autres manuels LIMIT Instrument de mesure

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur