Lightolier PENDALYTE SERIES Instructions d'utilisation

631

rpor

ver,

02720

COMPANY

READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING LUMINAIRE

This luminaire is intended for installation in accordance with the National Electrical Code and local regulations.

To assure full compliance with local codes and regulations, check with your local electrical inspector before

installation. To prevent electric shock, turn off electricity at fuse box before proceeding.

Retain these instructions for maintenance reference. IS:404S36

INSTRUCTION SHEET NO.

B0204 Page 1

Note: This instruction sheet covers several luminaire styles.

Powerhead assembly, lamp type, and reflector style may vary

slightly from that shown, although installation is the same.

INSTRUCTION SHEET FOR ASSEMBLY AND INSTALLATION

OF 9”,12”&16” PENDALYTE™ SERIES WITH

STEM

1. Using pipe cutting tool, shorten STEM to

appropriate length. Clean all burrs and sharp

edges from cut end of Stem.

2. Position DRILL LOCATOR over cut end of

STEM (Fig. 2). Gently tap down on DRILL

LOCATOR until fully seated on end of STEM.

3. Position CENTER PUNCH into bottom SLOT

in DRILL LOCATOR and mark a small dimple

in STEM (Fig. 3).

4. Align 1/8" DRILL BIT (local hardware item)

into bottom slot of DRILL LOCATOR so tip of

DRILL BIT rests in dimple (Fig. 4).

5. Drill hole completely through STEM allowing

DRILL LOCATOR to guide DRILL BIT. Do

not force DRILL BIT. It is recommended to

hold DRILL LOCATOR securely in a vise or

other device prior to drilling hole.

Instructions for shortening stem

ATTENTION: Cut end with smaller diameter holes only. (Fig.1)

CAUTION: Eye protection should always be worn when using hand and

power tools during the assembly procedure outlined below.

1. Assemble STEM to BALL ALIGNER using SET SCREWS. SET SCREWS

should align with small holes near end of stem. Pull wires through BALL

ALIGNER leaving no less than 6” exposed. (Fig 1)

2. Strip back insulation on Black, White and Green wires 3/8” at both ends.

3. Attach MOUNT PLATE to STEM by aligning holes as shown and inserting

PIN. Secure PIN with COTTER PIN.

4. Wire POWERHEAD ASSEMBLY using WIRE NUTS (local hardware item):

black luminaire lead to hot (black) lead, white luminaire lead to neutral (white)

lead. Attach luminaire ground wire(s) (green and/or bare) to green ground

wire.

5. Attach POWERHEAD to MOUNT PLATE with 8-32 SCREWS

6. Install SWIVEL CROSSBAR onto outlet box using OUTLET BOX SCREWS.

7. Insert STEM with BALL ALIGNER through CANOPY prior to wiring.

8. Place BALL ALIGNER with STEM into CROSS BAR through side access hole.

When seated the BALL ALIGNER KEYWAY will line up with tab on

CROSSBAR. Push supply leads into outlet box.

9. Slide SAFETY STRAP into position and secure with screw.

10. Make electrical connections: black lead to hot (black) supply lead; white lead

to neutral (white) supply lead. Green lead is ground wire and must be

connected to grounding terminal or ground lead inside outlet box. Use WIRE

NUTS (local hardware item). Note: Refer to POWERHEAD instruction

sheet for detailed wiring information.

11. Place CANOPY over CROSSBAR lining up slots on CANOPY with RUBBER

CAPS on CROSSBAR turning clockwise until it locks into place.

NOTE: If custom length is required see below

STEM

8-32 SCREW

COTTER PIN

MOUNT PLATE

POWERHEAD

ASSEMBLY

BALL ALIGNER

SET SCREW

SAFETY

STRAP

W/SCREW

OUTLET

BOX

SCREW

CANOPY

SWIVEL

CROSSBAR

RUBBER

CAPS

KEYWAY

Fig 1

Table des matières

Autres manuels Lightolier Luminaire

Lightolier

Lightolier Lytecaster 2022 Manuel utilisateur

Lightolier

Lightolier LW6CLP Manuel utilisateur

Lightolier

Lightolier Calculite C4P20D Manuel utilisateur

Lightolier

Lightolier Brisa FP14U Manuel utilisateur

Lightolier

Lightolier Calculite AS4LS Manuel utilisateur

Lightolier

Lightolier Lytespan 9022 Manuel utilisateur

Lightolier

Lightolier 4R28 Manuel utilisateur

Lightolier

Lightolier Lytespan 8330 Manuel utilisateur

Lightolier

Lightolier Lytecaster 1071 Manuel utilisateur

Lightolier

Lightolier BOWSHIELD “ADA” WALL BRACKET SERIES Mode d’emploi

Lightolier

Lightolier Brisa FC21U_3d Manuel utilisateur

Lightolier

Lightolier 4R42 Manuel utilisateur

Lightolier

Lightolier Calculite ProSpec PB3P3075 Manuel utilisateur

Lightolier

Lightolier ProSpec 26690 Manuel utilisateur

Lightolier

Lightolier Lytespan 6415 Manuel utilisateur

Lightolier

Lightolier 1102P1 Manuel utilisateur

Lightolier

Lightolier COVERS ALL MINI-BRACELET FIXTURE SERIES Mode d’emploi

Lightolier

Lightolier SLB2SFSVA432 Manuel utilisateur

Lightolier

Lightolier Calculite C12E28VW Manuel utilisateur

Lightolier

Lightolier Calculite DD Manuel utilisateur

Lightolier

Lightolier Lytecaster 1128 Manuel utilisateur

Lightolier

Lightolier Calculite ProSpec PA3P3810 Manuel utilisateur

Lightolier

Lightolier LFK Manuel utilisateur

Lightolier

Lightolier Lytespan 22SS3 Manuel utilisateur

Manuels Luminaire populaires d'autres marques

Emos

Emos CLASSIC ZY1431T Manuel utilisateur

Westinghouse

Westinghouse Outdoor Lighting Fixture Manuel utilisateur

Hedler

Hedler C 12 silent Manuel utilisateur

Blizzard Lighting

Blizzard Lighting Puck: CSI Manuel utilisateur

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manuel utilisateur

Lightmaxx

Lightmaxx Shaft 5R Manuel utilisateur

Triarch

Triarch 31083 Manuel utilisateur

Philips

Philips 32614 Series Manuel utilisateur

IKEA

IKEA TIVED Manuel utilisateur

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manuel utilisateur

Martin

Martin MAC 250 Krypton Manuel utilisateur

Cooper Lighting

Cooper Lighting Halo L3232E Manuel utilisateur

Stageline

Stageline ODW-2410RGBW Manuel utilisateur

Light Sky

Light Sky Tornado Series Manuel utilisateur

ArtFox

ArtFox Beam 15R extreme Manuel utilisateur

GLG

GLG multispot 330 Manuel utilisateur

Home Accents Holiday

Home Accents Holiday TY052-1924-1 Manuel utilisateur

SELF Electronics

SELF Electronics FLEX Manuel utilisateur