Lightmybricks Fire Brigade Manuel utilisateur

Light My Bricks : Fire Brigade LED Lighting Kit

Here is the instructions document for the LEGO Fire Brigade LED lighting kit. Please read

and follow the steps carefully to ensure this lighting kit is installed properly.

Package contents:

 1x Lamp Post with 30cm Bit Light installed

 4x White Bit Lights 30cm

 4x White Bit Lights 15cm

 2x White Flashing Bit Lights 15cm

 2x Red Flashing Bit Lights 30cm

 5x LED Strip Lights

 4x 15cm Connecting Cables

 1x 30cm Connecting Cable

 5x Adhesive Squares

 1x 12-port Expansion Board

 1x 8-port Expansion Board

 1x AA Battery Pack (Requires 3x AA Batteries)

 1x Flat Battery Pack (Requires 2x CR2032 Batteries)

Extra LEGO Pieces

 2x LEGO Trans Red 1×1 round bricks

 2x LEGO Light Grey 1L bar with mechanical claw clip

 4x LEGO Plates 1×6 for mounting Strip Lights

Important things to note:

Laying cables in between and underneath bricks

Cables can fit in between and underneath LEGO® bricks, plates, and tiles providing they

are laid correctly between the LEGO® studs. Do NOT forcefully join LEGO® together

around cables; instead ensure they are laying comfortably in between each stud.

CAUTION: Forcing LEGO® to connect over a cable can result in damaging the cable

and light.

Connecting cable connectors to Strip Lights

Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be

inserted only one way. With the Strip Light facing up, ensure the side of the connector

with the wires exposed is facing down. If a plug won’t fit easily into a port connector, don’t

force it. Doing so will damage the plug and the connector.

Connecting cable connectors to Expansion Boards

Take extra care when inserting connectors to ports of Expansion Boards. Connectors can

be inserted only one way. With the expansion board facing up, look for the soldered “=”

symbol on the left side of the port. The connector side with the wires exposed should be

facing toward the soldered “=” symbol as you insert into the port. If a plug won’t fit easily

into a port connector, do not force it.

Incorrectly inserting the connector can result in bent pins inside the port or

possible overheating of the expansion board when connected.

Installing Bit Lights under LEGO® bricks and plates.

When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way

up (Yellow LED component exposed). You can either place them directly on top of

LEGO® studs or in between.

OK, Let’s Begin!

Instructions for installing this kit

This section will guide you to install light to the fire truck first.

1) Start by removing the following pieces to allow us to remove one of the headlight

sections from the front.

Remove the trans yellow round plate and then take one White 15cm Bit Light and thread

the connector side through the front hole of the red brick as per below.

Autres manuels Lightmybricks Équipement d'éclairage

Lightmybricks

Lightmybricks LEGO IMPERIAL LIGHT CRUISER 75315 LIGHT KIT Manuel utilisateur

Lightmybricks

Lightmybricks LEGO AIRBUS H175 RESCUE HELICOPTER 42145 LIGHT... Manuel utilisateur

Lightmybricks

Lightmybricks LEGO MEDIEVAL CASTLE Manuel utilisateur

Lightmybricks

Lightmybricks 103035 Mode d’emploi

Lightmybricks

Lightmybricks 75574 Manuel utilisateur

Lightmybricks

Lightmybricks 76423 Manuel utilisateur

Lightmybricks

Lightmybricks 76408 Manuel utilisateur

Lightmybricks

Lightmybricks LEGO OPTIMUS PRIME Manuel utilisateur

Lightmybricks

Lightmybricks LEGO Fiat 500 10271 LED light kit Manuel utilisateur

Lightmybricks

Lightmybricks LEGO MARVEL SPIDER-MAN CARNAGE Manuel utilisateur

Lightmybricks

Lightmybricks LEGO AVENGERS TOWER Manuel utilisateur

Lightmybricks

Lightmybricks 76956 Manuel utilisateur

Lightmybricks

Lightmybricks LEGO THE GLOBE Manuel utilisateur

Lightmybricks

Lightmybricks Old Fishing Store Lighting Kit 103041 Manuel utilisateur

Lightmybricks

Lightmybricks 76209 Manuel utilisateur

Lightmybricks

Lightmybricks 21338 Manuel utilisateur

Lightmybricks

Lightmybricks LEGO UCS OBI-WAN's JEDI STARFIGHTER 10215 LIGHT... Manuel utilisateur

Lightmybricks

Lightmybricks LEGO 75276 Manuel utilisateur

Lightmybricks

Lightmybricks LEGO RETRO BOWLING ALLEY 910013 Manuel utilisateur

Lightmybricks

Lightmybricks 75339 Manuel utilisateur

Lightmybricks

Lightmybricks LEGO STAR WARS BD-1 75335 LIGHT KIT Manuel utilisateur

Lightmybricks

Lightmybricks 10299 Manuel utilisateur

Lightmybricks

Lightmybricks LEGO 1989 Batwing Manuel utilisateur

Lightmybricks

Lightmybricks LEGO STAR WARS UCS LUKE SKYWALKER'S... Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur