Life Smart LS-EF450 Guide de démarrage rapide

OWNERS INSTALLATION AND USER GUIDE

LIFESMART INFRARED FIREPLACE WALL HEATER

Model: LS-EF450

Safety Notice

Please read this entire Installation and Operating Manual BEFORE installing and using your new Infrared

Heater. Failure to fully understand and follow instructions may result in property damage, bodily injury, or

even death.

Unexpected mishaps may occur if the Infrared Heater in not used properly. For everyone’s safety, follow

ALL Installation and Operating Directions.

IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND

KEEP SAFE FOR FUTURE REFERENCE.

READ AND SAVE THESE INSTRUCTIONS

Important Safety Instructions

When using electrical appliances, basic precautions should always be followed to reduce the risk

of fire, electric shock and injury to person, including the following:

CAUTION- High temperature, keep electrical cords, drapery, and other furnishings at least 3 feet (0.9m) from

the front of the heater and away from the side and rear.

Read all instructions before using heater.

This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible materials,

such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet (0.9m) from the front of the heater and

keep them away from the sides and rear.

Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left

operating unattended.

Unplug power cord before servicing or moving the heater. Always unplug heater when not in use.

Do not operate any heater with a damaged cord or after the heater malfunctions, has been dropped or damaged in

any manner. Return heater to authorized service facility for examination, electrical or mechanical adjustment, or

repair.

Do not use outdoors.

This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate heater

where it may fall into a bathtub or other water container.

Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord away from

traffic area and where it will not be tripped over.

To disconnect heater, turn controls to off, then remove plug from outlet.

Connect to properly grounded outlets only.

Do not insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an

electric shock or fire or damage the heater. Do not block or tamper with the heater in any manner while it is in

operation.

A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable

liquids are used or stored.

Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause

fire, electrical shock, or injury to persons.

Avoid the use of extension cords because the extension cord may overheat and cause a risk of fire.

This heater includes an overheat protection system that shuts off the heater when parts of the heater are getting

excessively hot. If the heater shuts off, immediately turn the heater OFF and inspect for any objects, on or adjacent to

the heater, which may cause high temperatures. DO NOT OPERATE THE HEATER UNTIL IT IS RESET. To reset the

heater, turn it OFF, unplug it from the electrical outlet, and wait five to ten minutes for the unit to cool down before

plugging it back in and turning the heater on.

Make certain that the power source conforms to the electrical requirements of the heater.

A heater has hot and arcing or sparking parts inside. It must NOT be used in potentially dangerous locations such as

flammable, explosive, chemical-laden or wet atmosphere. This heater is intended for use in general use only.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or learning

disabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

WARNING: DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE MEANS OF POWERING DOWN THE

HEATER WHEN SERVICING OR MOVING. ALWAYS UNPLUG THE POWER CORD AS WELL.

Technical Specifications

· Supply: 110-120V~ 60Hz · Rated power: 1500W · Lighting: 40W E12 SES Clear Candle Bulb

Getting Started

· Remove the heater from the box.

· Remove any packaging materials from the product.

· Place the packaging inside the box and either store or dispose of safely.

Included In the Box:

·(Qty 1) Heater (with glass fireplace cover)·(Qty 1) Remote Control·(Qty 1) Instruction Manual

Mounting Hardware Pack: (Qty 1) Long Mounting Bracket·(Qty 1) Short Mounting Bracket

(Qty 6) Long Screws·(Qty 2) Short Screws·(Qty 6) Plastic Wall Plugs

Precautions To Consider Before Mounting

・2 People will be required to complete the mounting process.

・Keep all packaging until you have checked and counted all the parts and the contents of the mounting hardware.

・The mounting hardware pack contains small items that should be kept away from young children.

・We suggest that after opening the mounting hardware pack, you place all the contents into a container, to reduce the

risk of losing small pieces.

・Do not plug in or power up the heater until it is secure to the wall and the instructions are read fully.

・Please choose a mounting location wisely, prior to starting. A power outlet must be within the cord’s reach.

・The long mounting bracket must be secured horizontally, and the power cable routed to the bottom right of the heater.

・Please observe the recommended heights and dimensions for mounting the heater. This appliance is designed to be

mounted to a wall at a minimum height of 2 feet from the floor, and a minimum 3 feet from the ceiling (for optimum

heat ventilation).

・Note that the long mounting bracket will be “hooked” to the heater towards the top, rear edge of the heater, and not

the center. Consider this when mounting the bracket.

・Take necessary precautions to avoid cutting or damaging any cables or power cords.

・While drilling holes for the plugs, be cautious of electrical lines, metals, or items beyond the walls.

・Be sure that the wall you choose to mount on is solid, and will support the heater’s approximate weight (30lbs).

・Make sure that the heater is safely out of the way while you are installing mounting hardware, as it may become a

tripping hazard if left in the open.

・Please be cautious if you are set on mounting the heater low to the floor, as it may become a safety hazard to

children and pets!

Items Needed:

2 People · Mounting Hardware Pack · Power Drill · #6 Drill Bit · Medium Phillips

Screwdriver · Small Level · Pencil for marking the wall (if you think you may have to erase) or a Fine Tip

Marker ·Gloves

Mounting Instructions (Reference Figures 1-4 On Next Page)

1. Select a wall and room location to mount your heater.

a. Make sure it is a location where 1) the power cord will reach an outlet, 2) it is safe for kids and pets, and 3)

the heater vents will not be obstructed by pictures, curtains, or anything that may prevent rear vent airflow

(Ref. Fig. 1 for recommended placement dimensions, and useful heater dimensions)

2. Once the location is selected, take the mounting bracket and:

a. Line it up horizontally. The flat side should be up against the wall, with the “lip” towards the top of the

bracket, and leaning away from the wall.

b. Straighten the bracket with your level. This is very important to keep the weight distribution even.

c. Mark the four bracket screw positions on the wall, using your pencil or marker (Ref. Fig. 2A for detailed

bracket dimensions and mounting information)

3. Drill 4 holes on the wall with a #6 drill bit, using the locations you marked on the wall as guides.

4. Insert 4 wall plugs into each of the holes. They may feel snug at first, which is normal. You may use the screwdriver

handle to slightly tap them in until flush to the wall.

5. Once the plugs are secure, re-align the long mounting bracket to the holes, and use the long screws to secure it to the

wall (The screwdriver is recommended to avoid stripping the screws and plugs).

*At this point, remove the glass cover from the heater face, if not already done (Ref Fig.4 for removal).

6. With a second person assisting on either side, lift the heater up and engage the heater’s rear ledge to lip on the long

mounting bracket (Ref. Fig. 2B). Make sure it is centered, for even weight distribution.

*Note that the heater’s final resting position will be slightly angled downward. Do not release the heater

until it is safely resting against the wall.

7. With the heater resting, you can now take the small mounting bracket, and line it up against the heater’s underside

and the wall. Mark the 2 remaining wall plug locations accordingly (Ref. Fig. 3 A and B).

8. With a second person assisting, remove the heater and place to one side, and safely out of the way.

9. Drill the final 2 holes for the remaining plugs at your marked locations, and insert the plugs into the wall as in step

#4 above.

10. With a second person helping, re-mount the heater on to the long mounting bracket on the wall.

11. Install and secure the small mounting bracket to the heater’s underside by using the 2 small screws provided and the

2 remaining long screws to secure to the wall plugs.

12. With a second person assisting on either side, lift, and place the front glass cover over the fire display, assuring that

each of the 4 lugs aligns to each of the 4 bracket guides (Ref Fig. 4).

Replacing the Lamps/Bulbs (Reference Figures 5-8 Below)

Precautions Before Replacing Lamps/Bulbs

· Warning-Always disconnect the heater completely from the power outlet before replacing bulb.

· Warning-The bulbs reach high temperatures during operation. Allow the bulbs to cool completely after powering the

heater down, but before the replacement process.

· Note: Two people will be required for this process.

· Note: It is recommended that the heater be set on the floor, on its back (face up), in order to replace the bulbs.

The Process (After Powering Off and Unplugging)

1. Gently remove the glass panel from the heater “face.”

2. Store the glass safely out of the way so that it does not get tripped on or damaged.

3. With assistance from a second person, carefully dismount and lower the heater to the floor, face up.

4. Towards the lower part of the heater’s “face” there is a long, metal, rectangular cover, secured by three Philip's head

screws.

5. Remove the three screws and lift the cover up, and off (Ref. Fig 5).

6. Carefully bend the flexible tinsel bar towards you, while pulling and removing the left end of the bar from the rubber

grommet insert. Make sure the grommet stays in place and does not get lost (Ref. Fig 6 and 7).

*Lifting the loose end of the flexible bar should give you enough space for removing the bulbs.

7. Remove the defective bulb by unscrewing it counterclockwise (Ref. Fig 8).

8. Replace with a 40W E12 SES Clear Candle bulb, by screwing it clockwise.

*Make sure not to over-tighten the bulb, as it may cause damage to the bulb or the holder.

9. Reinstall the flexible tinsel bar by bending the bar towards you, while re-inserting into the grommet.

10. Make sure you “straighten” the flexible bar as much as possible (if you see bends) prior to re-installing the metal cover.

11. Once the bulbs are replaced, re-install the metal cover with the 3 screws.

12. With assistance from a second person, re-mount the heater onto the wall and re-install the glass cover.

Instructions For Use

· The heater can be operated either by the switches located on the top right hand side of the fire place or

by supplied remote control.

Manual Operation

· The switches are located at the top, right hand side of the heater.

· The standby switch must be switched on first, and foremost.

· Press O/I button once to turn on the heat and fire effect. The LED lights will light up to indicate that it is ON.

· Press the 750W button once for the low heat settings; press twice to switch off this heat setting.

· Press the 1500W button once for the high heat settings; press twice to switch off this heat setting.

Remote Operation

· For proper remote operation, the standby switch located at the top right hand side of the heater must first be

MANUALLY switched ON.

· It takes a little time for the receiver to respond to the transmitter. Be patient. DO NOT press the buttons more than one

time within two seconds to avoid cross signals.

· Press the ON/OFF button once the remote control to turn the heat and fire effect on or off.

· Press the 750W button once for the low heat settings; press twice to switch this heat setting off.

· Press the 1500W button once for the high heat settings; press twice to switch this heat setting off.

Safety Cut-Off

· This heater is equipped with an overheat safety cut-off switch that will engage if the heater overheats for any reason.

· For safety reasons, the heater will NOT automatically reset after the safety cut-off switch has engaged.

· To reset it, disconnect the heater from the main power outlet for at least 15 minutes.

· You can then reconnect it to the power outlet and switch it back on.

Maintenance

WARNING: ALWAYS UNPLUG THE CORD BEFORE MOVING OR SERVICING.

DO NOT IMMERSE HEATER IN WATER!

Always turn OFF the heater and disconnect the cord from the electrical outlet before cleaning your heater.

Light accumulated dust may be removed from the heater with a soft cloth or vacuum cleaner.

Wipe the exterior surfaces of the heater occasionally with a slightly damp cloth (not dripping wet) using a solution of mild

detergent and water. Dry the case thoroughly before operating the heater.

Caution: Do not allow water to run into the interior of the heater as this could create a fire or electric shock hazard.

The fan motor is factory lubricated for life and will not require further lubrication.

Store the heater in a clean dry place when not in use.

Warning: Any other servicing needed must be performed by an authorized service representative. Do not attempt to

service the unit yourself.

After Season Care:

Store the heater in a cool, dry location.

The manufacturer recommends storing the unit in its original carton.

Troubleshooting

Problem Solution

No operation/ no fan. Check for safety cut-off operation.

No fire effect light. Check the bulb by replacement.

Limited Manufacturer Warranty

1 Year Limited Warranty:

LIFESMART warrants this heater against defects in materials and workmanship on functional parts, for

a period of 1 year from the original date of purchase. Your sales receipt showing the date of purchase of

the product is your proof of purchase. Keep it in a safe place for future reference.

Manufacturer Warranty

All LIFESMART products are manufactured with the highest quality materials and are warranted to be

free from defects in material and workmanship at the time of purchase. This limited warranty applies to

products manufactured or distributed by the LIFESMART brand name, are delivered in the continental

United States, and extends to the original purchaser, or gift recipient. This warranty becomes valid at the

time of purchase and terminates either by the specified time frame listed above and/or owner transfer

(unless otherwise authorized by LIFESMART, as the manufacturer). Any extended warranties (warranties

that cover above and beyond this manufacturer warranty) that are sold through a retailer or third party, are

not directly correlated with this LIFESMART limited warranty, and may be redirected to said retailer or

third party for coverage.

Extent of Warranty

This warranty extends through the manufacturer of the product, and covers functional parts only.

Cosmetics are not covered, unless unequivocally determined it is a manufacturer/workmanship defect. Note

that surface cracks are not considered defects in material or workmanship, as they are normal characteristics

of all wood and some plastics. Unless LIFESMART was the direct shipper, shipping damage should be

addressed with the shipping company, retailer, or place of purchase, prior to making a claim to

LIFESMART, as the manufacturer.

The manufacturer's sole obligation under this warranty shall be limited to furnishing the original purchaser

replacement parts for units deemed repairable by the LIFESMART warranty department. The purchaser

may also opt to ship the product to LIFESMART to have it repaired. The purchaser will be responsible to

prepay any shipping charges (both ways), export taxes, custom duties and taxes, or any other charges

associated with the transportation of the unit. In addition, the purchaser is responsible for insuring any parts

shipped or returned, if desired. For products the warranty department deems un-repairable, or discontinued,

LIFESMART reserves the right to issue a refurbished product, or product similar in size and functionality

as a replacement for the defective unit, if available. All exchanged parts and products replaced under this

warranty will become the property of LIFESMART.LIFESMART reserves the right to change

manufacturers of replacement parts or products for use, in order to cover any existing warranty. Any parts

determined defective may asked to be returned to LIFESMART or its representatives to validate a claim.

Non-Warranty replacement parts will be warranted 30 days from the time the purchaser receives them.

The purchaser must present LIFESMART with proof of purchase documents (including the date of

purchase) if requested. Any evidence of alteration, erasing, or forgery of proof of purchase documents will

be just cause to VOID this limited warranty. Products, in which the serial number has been defaced or

removed, are not eligible for warranty coverage. Continued…

Warranty Limitations

This warranty does not apply if the unit has been subject to negligence, fabrication, misuse, abuse, or

repairs (unless authorized verbally, or in writing, by an Authorized LIFESMART Representative) alteration

by non LIFESMART authorized personnel, inappropriate installations, or any case beyond the control of

LIFESMART. Examples of warranty invalidation may also include, but are not limited to:

Use of lacquer or paints in (and around) the

heaters

Heater placed on non-approved surfaces

Electrical requirement deficiencies (15-20

amp dedicated outlet)

Use on Extension Cords/Timers/Surge

Protectors/GFCI

Outdoor applications

Normal wear/tear/weathering

Pet/Consumer accidents

Purchases from dealers unauthorized by

LIFESMART (Authorization in writing)

Disclaimers

LIFESMART shall not be liable for any loss due to use (or misuse) of the heater or other LIFESMART

products or other incidental or consequential costs, expense or damages without irrefutable foundations.

Under no circumstances shall LIFESMART or any of its representatives be held liable for injury to any

person or damage to any property, however arising. Any implied warranty shall have duration equal of the

applicable warranty stated above. Specifications are subject to change without notice or obligation.

Legal Remedies

This limited warranty gives the original purchaser specific legal rights. Other rights may vary from state

to state.

Customer Service and Support

To Obtain Warranty Support or Advice, Please Complete These Two Easy Steps:

Contact LIFESMART PRODUCTS Technical Support

E-mail:Warranty@lifesmartproducts.com

Phone:1-866-484-2066

You will need to provide the unit's model number, serial number (located

on the heater’s front panel, rear panel, or on the box), date of purchase,

retailer of purchase, a daytime phone number, and possibly a copy of your

receipt.

Be Patient, Clear, and Concise.

Describe the issue and symptoms you have for, and about the product. A

certified LIFESMART Technical Support agent will give you an evaluation

of your issue and your resolution options. If the answer is not available at

that time, you will be referred to the appropriate channels, or given a call/e-

mail back within 72 hours with an answer or resolution.

*E-Mail is the Preferred Method of Communication

Table des matières

Autres manuels Life Smart Chauffage

Life Smart

Life Smart LS?Stealth?4 Manuel utilisateur

Life Smart

Life Smart R-HT1156 Manuel utilisateur

Life Smart

Life Smart MCHT1153US Manuel utilisateur

Life Smart

Life Smart LS1000HH13 Guide de démarrage rapide

Life Smart

Life Smart LS-IF1500-MOFP Guide de démarrage rapide

Life Smart

Life Smart LS-8WIQH-LB Manuel utilisateur

Life Smart

Life Smart LS-Stealth-1 Manuel utilisateur

Life Smart

Life Smart HT1269UV Manuel utilisateur

Life Smart

Life Smart LS-PP1500-6NAT Manuel utilisateur

Life Smart

Life Smart LS-1500X-6WB Guide de démarrage rapide

Life Smart

Life Smart LS-PP1800-6WCH Manuel utilisateur

Life Smart

Life Smart ZCHT1074US Manuel utilisateur

Life Smart

Life Smart LS-1000X-4W Manuel utilisateur

Life Smart

Life Smart HT1167 Manuel utilisateur

Life Smart

Life Smart Ultra LS1500-4WC Manuel utilisateur

Life Smart

Life Smart KUH25-01 Manuel utilisateur

Life Smart

Life Smart LS-1000X-4M Manuel utilisateur

Life Smart

Life Smart HT1193 Manuel utilisateur

Life Smart

Life Smart XXAC3004US Manuel utilisateur

Life Smart

Life Smart LS-1000X-6W Manuel utilisateur

Life Smart

Life Smart XXHT1141US Manuel utilisateur

Life Smart

Life Smart LS-4W1500-X Guide de démarrage rapide

Life Smart

Life Smart LS-500-1WP Guide de démarrage rapide

Life Smart

Life Smart LS-1000X-4M Manuel utilisateur

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur