Life Smart HT1289 Manuel utilisateur

Questions, problems, missing parts? Contact technical support department at

657-341-0362, 9:00 a.m. - 5 p.m., PST, Monday - Friday or visit us online at

www.lifesmartcomfort.com

Please have your model and serial number ready

ATTACH YOUR RECEIPT HERE

Purchase Date ____________Serial Number (located on back of unit) __________________

LIFE SMART® is a registered trademark of

REV1-080520

INFRARED HEATER

Customer number:

HT1289

UNIT LEGS LOCATED UNDERNEATH THE BOTTOM MOST PACKAGING FOAM

TABLE OF CONTENTS

Package Contents ............................................................... 3

Safety Information .............................................................. 4

Frequently Asked Questions ...................................................... 6

Preparation .................................................................... 8

Troubleshooting ................................................................ 8

Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Remote Control ................................................................ 10

Operating Instructions .......................................................... 11

Care and Maintenance .......................................................... 13

One-Year Limited Warranty ...................................................... 14

Replacement Parts List ......................................................... 15

PACKAGE CONTENTS

PART DESCRIPTION QUANTITY

A Infrared Heater 1

B Remote Control 1

C Control Panel (preassembled to Infrared Heater (A)) 1

D Temperature Sensor (preassembled to Infrared Heater (A)) 1

E Unit Legs (*assembly required, see pg8) 4

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate, or install the product.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: POTENTIAL ELECTRICAL HAZARD IF NOT ADHERED TO. When using electrical

appliances, basic precautions should always be followed to reduce the risk of ﬁre, electric shock, and

injury to persons, including the following:

• This heater must be plugged into a 120 V, 15 amp (or more) circuit of its own. Do not plug anything

else into the same circuit. If unsure if your home meets this speciﬁcation, consult a certiﬁed

electrician prior to use. Risk of ﬁre, overheating, malfunction, property damage, injury, or even

death may result if not adhered to!

• Connect to a properly grounded, outlet only. Do not connect the heater to extension cords, surge

protectors, timers, direct breakers, or an outlet with other appliances connected to the same outlet.

Risk of ﬁre, overheating, malfunction, property damage, injury, or even death may result if not

adhered to!

• This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Use handles

(certain models) or wheels to move this heater.

• Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at

least 3 ft. (0.9 m) from the front of the heater and keep them away from the sides and rear of the

heater.

• Extreme caution is necessary when any heater is used by or near children, invalids, pets, or when

the heater is left operating unattended.

• Always unplug the heater when not in use.

• Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been

dropped, or damaged in any manner. Contact the manufacturer for resolution options.

• Do not use outdoors. Exposure to outdoor elements such as rain, snow, sun, wind, or extreme

temperatures may cause the heater to become a safety hazard.

• This heater is not intended for use in bathrooms, laundry areas, and similar indoor locations, nor

any locations that use GFCI outlets.

• Never place the heater where it may fall into a bathtub or other water receptacles.

• Do not run the cord under carpet. Do not cover the cord with throw rugs, runners, or similar

coverings. Arrange the cord away from trafﬁc areas and where it will not be tripped over.

• The heater must be plugged into a wall outlet that is a dedicated circuit with a minimum 15 amp

rating on that individual circuit.

• To disconnect the heater, ﬁrst turn the power button to the OFF position and then remove the plug

from the wall outlet.

• Do not allow foreign objects to enter or block any ventilation or exhaust opening as this may cause

electric shock, ﬁre, or damage the heater.

• Allow at least 3 ft. of unobstructed space to the front and rear of the heater to allow for maximum

heat, air, and ventilation ﬂow.

• A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint,

or ﬂammable liquids are used or stored, nor use ﬂammable solvents to clean the heater. Keep the

heater dry at all times.

• Use this heater only as described in this manual. Any other use not recommended by the

manufacturer may cause ﬁre, electric shock, or injury to persons.

• Do not use abrasive solvents to clean the heater as it may cause damage to the ﬁnish or casing.

• To prevent a possible ﬁre, do not block air intakes or exhaust in any manner. Do not use on soft

surfaces, like a bed, where opening may become blocked.

• Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or

relocatable power tap (outlet/power strip).

SAVE THESE INSTRUCTIONS

SAFETY INFORMATION

Child Lock Safety Feature

Press and hold the ﬂame button on the remote control (B) for

5 seconds. Locking is conﬁrmed when a buzzer rings. When

locked, the control panel and remote control (if provided) will not

function.

To unlock the control panel or remote (if provided), repeat this

procedure. Unlocking is conﬁrmed when a buzzer rings.

Tip-Over Safety Feature

This heater is equipped with a tip-over safety feature. Once the heater is tipped over, an internal

switch will automatically shut the heater off. Once the heater is restored to an upright position, the

heater will reset. To continue operation, turn on the heater using the control panel or supplied remote

control (if provided) on the heater.

Overheat Safety Feature

This heater is equipped with an overheat safety feature. When the internal components of the heater

reach a certain temperature that could cause overheating or possible ﬁre, the heater will automatically

shut off. If the unit has been overheated, you will need to unplug the unit from the wall and replug it in

to use the heater again.

WARNING: TO PREVENT ELECTRICAL SHOCK,

MATCH THE WIDE BLADE OF THE PLUG TO THE

WIDE SLOT OF THE RECEPTACLE AND FULLY

INSERT.

WARNING: It is normal for the power cord to feel warm to the touch. However, a loose ﬁt between

the outlet and the plug may cause overheating of the plug. If this occurs, try inserting the plug into a

different outlet. Contact a qualiﬁed electrician to inspect the original outlet for damage.

Speciﬁcations

Voltage Rating 120 V (60 Hz)

Power Consumption 1,000 W/1,500 W

Unit Size 16.60 in. (W) x 10.70 in. (D) x 22.44 in. (H)

Unit Weight 10.45 lbs.

FREQUENTLY ASKED QUESTIONS

Please review these frequently asked questions on the next few pages prior to using your heater.

Q. My heater emits a strange odor when I ﬁrst open the box and when I turn the heater on for the ﬁrst

time. Why is this happening?

A. This is normal. This heater is treated with a special heat safe/resistant coating. This odor will

sometimes be present when the box is opened. When the coating is exposed to heat, it produces this

particular odor during the ﬁrst few hours of operation. This will dissipate after the break-in period. If

you are sensitive to odors, you may want to pre-burn the unit in a garage with the door open until the

initial odor dissipates.

Q. If my heater runs on its max wattage setting, how many BTUs is that?

A. This heater is intended to be used as supplemental heat in areas most needed. It may take several

minutes to several hours to heat your area, depending on various factors. The below chart provides BTU

translations for different wattages.

WATTAGE BTUS

1,500 5,118

1,000 3,412

750 2,559

500 1,706

Q. Can the heating elements be replaced?

A. Replacement heating elements can be obtained from the manufacturer. All parts may be purchased

through the manufacturer if your product is out of warranty. If you feel that the elements are deﬁnitely

faulty right out of the box, contact Customer Support. A representative can then direct you to the next

step.

Q. Once I plug the unit in and turn it on, how long will it take to heat my room?

A. The heating process in the heater begins immediately upon powering on and setting the desired

temperature above the ambient temperature. A noticeable change in the ambient temperature of the

room will vary due to variables such as the location of the heater (in the home), ﬂoor plan and size of

the room, how well the room is insulated, how many doors/windows, how much bare concrete (acts as

a heat sink with any type of heating), the opening and closing of an exterior door, long hallways, high

ceilings, etc. Customers with smaller rooms experience quick heat changes. Rooms with larger and

open ﬂoor plans can expect up to 24 hours to completely heat up.

FREQUENTLY ASKED QUESTIONS

Q. The temperature on my heater does not match the temperature display on my wall, or external

thermostat. Why?

A. This is completely normal. The temperature display on your heater may vary from the temperature

display on another thermostat (like the one mounted to your wall or a purchased external thermostat).

This is because the temperature sensor on the heater reads the temperature directly around the heater.

With the heater near the cold ﬂoor (and heat rising), any readings on elevated or external thermostats

will differ in readings on the heater. The best way to operate your heater is to set the unit on High and

dial up to a temperature that feels comfortable to you. Then, leave it at that temperature, regardless of

the mismatch. The heater will cycle off when the set temperature is met or exceeded slightly.

Q. Can I use more than one heater at a time? Can I use the heater and another appliance at the same

time?

A. Yes, but make sure they are not plugged into the same circuit. Each heater requires its own minimum

15-amp circuit with no other items plugged into that circuit or outlet. This is because heaters are

considered appliances and draw out high amperage. If you are unsure your circuit meets these

requirements, verify with a certiﬁed electrician.

WARNING: Risk of ﬁre, damage to property, or injury may result if requirements are not met.

Q. Why does my heater’s fan continue to run after the set temperature is reached or the power is turned

off?

A. This is normal. The heater’s fan will continue to run even after the heater automatically cycles down.

The fan continues to run so that every last bit of heat is blown out of the heat chamber while allowing

the unit to continue ﬁltering your air. Once the internal box/components cool completely, the fan should

then shut off on its own. In this case, allow a few minutes after the heat cycles off (with power on). The

fan will shut off faster when the power is turned off.

Q. My heater’s display shows my ambient temperature to be in the 20s when I know it is warmer than

that. Why?

A. The heater’s display is defaulted to read the temperature as Fahrenheit. If your heater is deﬁnitely

heating but shows it is in the 20s you probably have the setting to read your temperature in Celsius

rather than Fahrenheit.

Q. My heater’s power cord gets warm. My cord is showing signs of heat or melting at the outlet. Is

this normal?

A. A warm power cord is normal. These power cords are rated safe for up to 105°C/ 221°F by the UL,

CSA, or ETL. The exception is, if you detect heat, smoke, or signs of melting at the contact point of

the wall outlet, it may be due to loose or worn wall contacts (or arcing). Please stop using the heater

immediately, contact warranty support for a replacement power cord, and have a certiﬁed electrician

replace the wall outlet as soon as possible.

PREPARATION

Place the heater on a ﬁrm, level surface and plug into a grounded 120 V, 60 Hz power outlet and turn on

the unit. Only operate heater in upright position.

Insert two AAA batteries into the remote control before using (batteries not included). *(Not all products

will include a remote control.)

Please note that infrared heaters do not heat like a traditional space heater. You should not expect

infrared heaters to blow hot air like a traditional space heater. Infrared heaters heat objects not air.

Infrared heaters are intended to supplement an already heated, insulated room. Square footage

speciﬁcations assume a single enclosed room not an entire home. Infrared heaters do not heat through

walls, ﬂoors, and are not intended to replace a main heat source. Infrared heat can take at least 24

hours to warm a room but operate much more efﬁciently to maintain the desired temperature. Infrared

heaters will not work well in uninsulated unheated spaces like screened in porches, RV’s, garages,

unheated basements, etc.

UNIT LEG ASSEMBLY

To assemble the unit feet align the foot to the

mounting bracket and press up ﬁrmly until se-

cured with a “CLICK” sound. For permanent

attachment you can secure the leg by adding

a screw into the pre-drilled hole (1 per leg).

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION

The heater

does not turn

on.

1. The power cord is not plugged in.

2. The electricity at the main fuse

box is not working.

1. Plug the power cord into an electrical

outlet.

2. Check the electricity at the main fuse

box.

The ﬂame

effect does not

turn on

1. The ﬂame intensity is low. 1. Increase the ﬂame intensity with the

ﬂame button.

There is no

heat from the

unit

1. The thermostat on the heater

is set lower than the room

temperature.

2. The switch for heat is not on.

1. Increase the thermostat temperature

on the heater to a higher heat setting.

2. Select High or Low heat setting and

increase the thermostat temperature to

a higher setting.

The heater

shutoff

unexpectedly

1. The heater has overheated.

2. Insufﬁcient power to the unit

3. The air vent is clogged.

4. Insufﬁcient air ﬂow to the heater.

1. Unplug the heater from the wall, wait a

few seconds then plug the power cord

back in.

2. Make sure the unit is plugged into a

dedicated outlet, with no extension

cords or surge protectors.

3. Clean the air vent located on the back of

the unit. see page 14.

4. Move the unit at least 3ft from the wall.

The heater

displays an

error code

“E2”

1. Temperature sensor not

functioning properly.

1. Please contact technical support.

CONTROL PANEL

109

87654321

High Low

Mode Temp Up Temp Down Timer Flame EectPower

PART NAME DESCRIPTION

1 Heater Mode Button Toggles between Hi / Low Heat Modes

2 Temp-Up Button Increases the set temperature

3 Temp-Down Button Decreases the set temperature

4 Short Press: Timer Button

Long Press: Ambient Temp

Short Press Engages the on/off timer function

Long Press for 5 seconds to Display Ambient Room

Temperature

5 Short Pres: Flame Effect Button

Long Press: C/F Button

Short Press Toggles the Flame Effect ON / OFF and

between the varied ﬂame effect brightnesses.

Long Press for 5 Seconds to switch between Celsius

and Fahrenheit

6 Power Switch Button Powers the heater ON or OFF

7 Power Indicator Light Indicates when unit is receiving power

8 Digital Display Readout of the set room temperature or timer value

9 High Heat Indicator Light Indicates when High Heat mode is on

10 Low Heat Indicator Light Indicates when Low Heat mode is on

Table des matières

Autres manuels Life Smart Chauffage

Life Smart

Life Smart HT1041 Manuel utilisateur

Life Smart

Life Smart LS-3W-BPIQT Manuel utilisateur

Life Smart

Life Smart LS-1000X-4C Manuel utilisateur

Life Smart

Life Smart LS-IF1500-MOFP Guide de démarrage rapide

Life Smart

Life Smart LS-PP1800-6WCH Manuel utilisateur

Life Smart

Life Smart LS-3ECO Manuel utilisateur

Life Smart

Life Smart LS-Stealth-1 Manuel utilisateur

Life Smart

Life Smart HT1167 Manuel utilisateur

Life Smart

Life Smart LS‐Stealth‐6 Manuel utilisateur

Life Smart

Life Smart XXAC3004US Manuel utilisateur

Life Smart

Life Smart LS?Stealth?4 Manuel utilisateur

Life Smart

Life Smart LS-1000X-6W Guide de démarrage rapide

Life Smart

Life Smart PCHT1109US Manuel utilisateur

Life Smart

Life Smart LS-1000X-4W Manuel utilisateur

Life Smart

Life Smart LS-PP1500-6NAT Manuel utilisateur

Life Smart

Life Smart LS-500-1WP Guide de démarrage rapide

Life Smart

Life Smart R-LS-W6-WIQH-M Manuel utilisateur

Life Smart

Life Smart XXHT1086US Manuel utilisateur

Life Smart

Life Smart LS-1000X-4M Manuel utilisateur

Life Smart

Life Smart LS-3ECO Manuel utilisateur

Life Smart

Life Smart LS1000-2 Manuel utilisateur

Life Smart

Life Smart R-HT1156 Manuel utilisateur

Life Smart

Life Smart LS1000HH13 Guide de démarrage rapide

Life Smart

Life Smart KUH25-01 Manuel utilisateur

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur