Life Smart HT1216 Manuel utilisateur

Questions, problems, missing parts? Contact technical support department at

657-341-0362, 9:00 a.m. - 5 p.m., PST, Monday - Friday or contact us via email at

cs@scsources.com

Please have your model and serial number ready

1REV1-100919

ATTACH YOUR RECEIPT HERE

Purchase Date ____________Serial Number (located on back of unit) __________________

lifesmart® is a registered trademark of

INFRARED TOWER HEATER

Customer number:

HT1216

TABLE OF CONTENTS

Package Contents ............................................................... 3

Safety Information .............................................................. 4

Frequently Asked Questions ...................................................... 6

Preparation .................................................................... 8

Troubleshooting ................................................................ 8

Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Remote Control ................................................................ 10

Operating Instructions .......................................................... 11

Care and Maintenance .......................................................... 13

One-Year Limited Warranty ...................................................... 14

Replacement Parts List ......................................................... 15

PACKAGE CONTENTS

Temp Up

Temp Down

Time

OSC ON/OFF

H/L/E

PART DESCRIPTION QUANTITY

A Infrared Heater 1

B Remote Control 1

C Control Panel (preassembled to Infrared Heater (A)) 1

DBroadrange Oscillation Vent (preassembled to Infrared Heater

(A)) 1

E Temperature Sensor (preassembled to Infrared Heater (A)) 1

F Master Power Switch (preassembled to Infrared Heater (A)) 1

G Air Intake Vent (preassembled to Infrared Heater (A)) 1

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate, or install the product.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: POTENTIAL ELECTRICAL HAZARD IF NOT ADHERED TO. When using electrical appliances,

basic precautions should always be followed to reduce the risk of ﬁre, electric shock, and injury to persons,

including the following:

• This heater must be plugged into a 120 V, 15 amp (or more) circuit of its own. Do not plug anything else

into the same circuit. If unsure if your home meets this speciﬁcation, consult a certiﬁed electrician

prior to use. Risk of ﬁre, overheating, malfunction, property damage, injury, or even death may

result if not adhered to!

• Connect to a properly grounded, 3-prong outlet only. Do not connect the heater to extension cords,

surge protectors, timers, direct breakers, or an outlet with other appliances connected to the same

outlet. Risk of ﬁre, overheating, malfunction, property damage, injury, or even death may result if

not adhered to!

• This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Use handles

(certain models) or wheels to move this heater.

• Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least

3 ft. (0.9 m) from the front of the heater and keep them away from the sides and rear of the heater.

• Extreme caution is necessary when any heater is used by or near children, invalids, pets, or when the

heater is left operating unattended.

• Always unplug the heater when not in use.

• Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been

dropped, or damaged in any manner. Contact the manufacturer for resolution options.

• Do not use outdoors. Exposure to outdoor elements such as rain, snow, sun, wind, or extreme

temperatures may cause the heater to become a safety hazard.

• This heater is not intended for use in bathrooms, laundry areas, and similar indoor locations, nor any

locations that use GFCI outlets.

• Never place the heater where it may fall into a bathtub or other water receptacles.

• Do not run the cord under carpet. Do not cover the cord with throw rugs, runners, or similar coverings.

Arrange the cord away from trafﬁc areas and where it will not be tripped over.

• The heater must be plugged into a wall outlet that is a dedicated circuit with a minimum 15 amp rating

on that individual circuit.

• To disconnect the heater, ﬁrst turn the power button to the OFF position and then remove the plug

from the wall outlet.

• Do not allow foreign objects to enter or block any ventilation or exhaust opening as this may cause

electric shock, ﬁre, or damage the heater.

• Allow at least 3 ft. of unobstructed space to the front and rear of the heater to allow for maximum heat,

air, and ventilation ﬂow.

• A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or

ﬂammable liquids are used or stored, nor use ﬂammable solvents to clean the heater. Keep the heater

dry at all times.

• Use this heater only as described in this manual. Any other use not recommended by the manufacturer

may cause ﬁre, electric shock, or injury to persons.

• Do not use abrasive solvents to clean the heater as it may cause damage to the ﬁnish or casing.

• To prevent a possible ﬁre, do not block air intakes or exhaust in any manner. Do not use on soft

surfaces, like a bed, where opening may become blocked.

• Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or

relocatable power tap (outlet/power strip).

SAVE THESE INSTRUCTIONS

SAFETY INFORMATION

Child Lock Safety Feature

Press and hold the child lock button located on the control panel for 5 seconds.

Locking is conﬁrmed when a buzzer rings and the control panel displays “CL”. When

locked, the control panel and remote control (if provided) will not function.

To unlock the control panel or remote (if provided), repeat this procedure. Unlocking

is conﬁrmed when a buzzer rings and the lock indication disappears.

Tip-Over Safety Feature

This heater is equipped with a tip-over safety feature. Once the heater is tipped over, an internal switch

will automatically shut the heater off. Once the heater is restored to an upright position, the heater will

reset. To continue operation, turn on the heater using the control panel or supplied remote control (if

provided) on the heater.

Overheat Safety Feature

This heater is equipped with an overheat safety feature. When the internal components of the heater reach

a certain temperature that could cause overheating or possible ﬁre, the heater will automatically shut off.

If the unit has been overheated, you will need to unplug the unit from the wall and replug it in to use the

heater again.

WARNING: This heater has a voltage rating of

120 volts. The cord has a three-blade, grounding-

type plug. An adapter is available for connecting

three-blade grounding-type plugs to two-slot

receptacles. The grounding lug extending from

the adapter must be connected to a permanent

ground such as a properly grounded outlet box.

The adapter should not be used if a three-slot

grounded receptacle is available.

DO NOT DEFEAT THE SAFETY PURPOSE OF THE

GROUNDED PLUG.

Grounding Pin

Grounding Means

Grounding Pin

Metal Screw

Cover of Grounded

Outlet Box

WARNING: It is normal for the power cord to feel warm to the touch. However, a loose ﬁt between the

outlet and the plug may cause overheating of the plug. If this occurs, try inserting the plug into a differ-

ent outlet. Contact a qualiﬁed electrician to inspect the original outlet for damage.

Speciﬁcations

Voltage Rating 120 V (60 Hz)

Power Consumption 1,000 W/1,500 W

Unit Size 10.50 in. (W) x 9.5 in. (D) x 23.25 in. (H)

Unit Weight 23.28 lbs.

FREQUENTLY ASKED QUESTIONS

Please review these frequently asked questions on the next few pages prior to using your heater.

Q. My heater emits a strange odor when I ﬁrst open the box and when I turn the heater on for the ﬁrst

time. Why is this happening?

A. This is normal. This heater is treated with a special heat safe/resistant coating. This odor will sometimes

be present when the box is opened. When the coating is exposed to heat, it produces this particular odor

during the ﬁrst few hours of operation. This will dissipate after the break-in period. If you are sensitive to

odors, you may want to pre-burn the unit in a garage with the door open until the initial odor dissipates.

Q. If my heater runs on its max wattage setting, how many BTUs is that?

A. This heater is intended to be used as supplemental heat in areas most needed. It may take several

minutes to several hours to heat your area, depending on various factors. The below chart provides BTU

translations for different wattages.

WATTAGE BTUS

1,500 5,118

1,000 3,412

750 2,559

500 1,706

Q. Can the heating elements be replaced?

A. Replacement heating elements can be obtained from the manufacturer. All parts may be purchased

through the manufacturer if your product is out of warranty. If you feel that the elements are deﬁnitely

faulty right out of the box, contact Customer Support. A representative can then direct you to the next step.

Q. Once I plug the unit in and turn it on, how long will it take to heat my room?

A. The heating process in the heater begins immediately upon powering on and setting the desired

temperature above the ambient temperature. A noticeable change in the ambient temperature of the

room will vary due to variables such as the location of the heater (in the home), ﬂoor plan and size of the

room, how well the room is insulated, how many doors/windows, how much bare concrete (acts as a heat

sink with any type of heating), the opening and closing of an exterior door, long hallways, high ceilings, etc.

Customers with smaller rooms experience quick heat changes. Rooms with larger and open ﬂoor plans

can expect up to 24 hours to completely heat up.

Q. I do not have a grounded outlet. Can I use adapters, a 2-prong power strip, or remove the ground

prong from the cord?

A. NO! If you do not have a grounded outlet, contact a certiﬁed electrician for advice. Removing or altering

any part of the heater’s original design or intent (including the power cord) will void the warranty and

make you liable for any unexpected or hazardous results.

Q. My Heater has an ECO setting? How does this setting work?

A. The ECO mode on your heater is a program that attempts to keep the temperature strictly at a “warm”

68° F (20°C). This also helps with efﬁciency, as it is programmed to 1) Increase the power to the unit’s

maximum wattage if the temperature drops below 64.4°F (18°C) 2) Gradually reduce the wattage used

as it approaches 66.2° (19°C) F and 3) Stop heating when 68° F (20°C) is achieved. This is considered an

Economical function, since in the ECO setting, the heater is almost never running at the maximum watts.

FREQUENTLY ASKED QUESTIONS

Q. The temperature on my heater does not match the temperature display on my wall, or external

thermostat. Why?

A. This is completely normal. The temperature display on your heater may vary from the temperature

display on another thermostat (like the one mounted to your wall or a purchased external thermostat).

This is because the temperature sensor on the heater reads the temperature directly around the heater.

With the heater near the cold ﬂoor (and heat rising), any readings on elevated or external thermostats

will differ in readings on the heater. The best way to operate your heater is to set the unit on High and dial

up to a temperature that feels comfortable to you. Then, leave it at that temperature, regardless of the

mismatch. The heater will cycle off when the set temperature is met or exceeded slightly.

Q. Can I use more than one heater at a time? Can I use the heater and another appliance at the same

time?

A. Yes, but make sure they are not plugged into the same circuit. Each heater requires its own minimum 15-

amp circuit with no other items plugged into that circuit or outlet. This is because heaters are considered

appliances and draw out high amperage. If you are unsure your circuit meets these requirements, verify

with a certiﬁed electrician.

WARNING: Risk of ﬁre, damage to property, or injury may result if requirements are not met.

Q. Why does my heater’s fan continue to run after the set temperature is reached or the power is turned off?

A. This is normal. The heater’s fan will continue to run even after the heater automatically cycles down.

The fan continues to run so that every last bit of heat is blown out of the heat chamber while allowing the

unit to continue ﬁltering your air. Once the internal box/components cool completely, the fan should then

shut off on its own. In this case, allow a few minutes after the heat cycles off (with power on). The fan will

shut off faster when the power is turned off.

Q. My heater’s display shows my ambient temperature to be in the 20s when I know it is warmer than

that. Why?

A. The heater’s display is defaulted to read the temperature as Fahrenheit. If your heater is deﬁnitely

heating but shows it is in the 20s you probably have the setting to read your temperature in Celsius rather

than Fahrenheit.

Q. My heater’s power cord gets warm. My cord is showing signs of heat or melting at the outlet. Is this

normal?

A. A warm power cord is normal. These power cords are rated safe for up to 105°C/ 221°F by the UL, CSA,

or ETL. The exception is, if you detect heat, smoke, or signs of melting at the contact point of the wall

outlet, it may be due to loose or worn wall contacts (or arcing). Please stop using the heater immediately,

contact warranty support for a replacement power cord, and have a certiﬁed electrician replace the wall

outlet as soon as possible.

PREPARATION

Place the heater on a ﬁrm, level surface and plug into a grounded 120 V, 60 Hz power outlet and turn on

the power switch on the rear of the unit. Only operate heater in upright position.

Insert two AAA batteries into the remote control before using (batteries not included). *(Not all products

will include a remote control.)

Please note that infrared heaters do not heat like a traditional space heater. You should not expect infrared

heaters to blow hot air like a traditional space heater. Infrared heaters heat objects not air. Infrared

heaters are intended to supplement an already heated, insulated room. Square footage speciﬁcations

assume a single enclosed room not an entire home. Infrared heaters do not heat through walls, ﬂoors, and

are not intended to replace a main heat source. Infrared heat can take at least 24 hours to warm a room

but operate much more efﬁciently to maintain the desired temperature. Infrared heaters will not work

well in uninsulated unheated spaces like screened in porches, RV’s, garages, unheated basements, etc.

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION

The heater does

not turn on.

1. The power cord is not plugged in.

2. The electricity at the main fuse

box is not working.

3. The battery in the remote control

is dead.

4. The thermostat on the heater

is set lower than the room

temperature.

5. The power switch in the back of

the unit is not in the ON position.

1. Plug the power cord into an electrical

outlet.

2. Check the electricity at the main fuse

box.

3. Replace the batteries in the remote

control.

4. Increase the thermostat temperature

on the heater for a higher heat setting.

5. Switch the power switch to the ON

position.

The heater

displays an error

code “E1”

1. The heater has overheated.

2. Insufﬁcient power to the unit

3. The air ﬁlter is clogged.

4. Insufﬁcient air ﬂow to the heater.

1. Unplug the heater from the wall, wait a

few seconds then plug the power cord

back in.

2. Make sure the unit is plugged into

a dedicated 3-prong outlet, with no

extension cords or surge protectors.

3. Clean the air ﬁlter located on the back

of the unit. see page 13.

4. Move the unit at least 3ft from the wall.

The heater

displays an error

code “E2”

1. Temperature sensor not

functioning properly.

1. Please contact technical support.

CONTROL PANEL

1 2 3

78910111213

PART NAME DESCRIPTION

1 Fan Indicator Light Indicates when the Fan is ON

2 Timer Indicator Light Indicates when the timer function is active

3 Digital Display Readout of the set room temperature or timer value

4 Celsius Indicator Light Indicates that the temperature is being displayed in Celsius

5 Fahrenheit Indicator Light Indicates that the temperature is being displayed in Fahrenheit

6 Power Indicator Light Indicates when the unit is receiving power from the wall outlet

7 Power Switch Button Powers the heater ON or OFF

8 Oscillation Button Toggles the oscillation vent ON / OFF

9 Temp-Down Button Decreases the set temperature

10 Temp-Up Button Increases the set temperature

11 Timer Button Engages the on/off timer function

12 Heater Mode Button Toggles between Hi / Low / Eco Modes

13 Safety Lock Button Hold to Lock / Unlock heater’s control panel

14 Energy Saving Indicator Indicates when energy-saving mode is on

15 High Heat Indicator Indicates when High Heat mode is on

16 Low Heat Indicator Indicates when Low Heat mode is on

REMOTE CONTROL

Temp Up

Temp Down

Time

OSC ON/OFF

H/L/E

PART NAME DESCRIPTION

1 Temp Up Button Increases the set temperature value

2 Mode Button Toggles between the three heat modes available

3 Temp Down Button Decreases the set temperature value

4 Power Button Powers the heater on or off

5Oscillation/Lock

Button Engages oscillation function/engages child lock function

6 Timer Button Engages the on/off timer

Table des matières

Autres manuels Life Smart Chauffage

Life Smart

Life Smart LS1002THD13 Manuel utilisateur

Life Smart

Life Smart LS1000-2 Manuel utilisateur

Life Smart

Life Smart R-LS-W6-WIQH-M Manuel utilisateur

Life Smart

Life Smart LS-Stealth-6FP Manuel utilisateur

Life Smart

Life Smart LS-6BPIQH-X Guide de démarrage rapide

Life Smart

Life Smart LS-1000X-6W Manuel utilisateur

Life Smart

Life Smart LS-1000X-4C Manuel utilisateur

Life Smart

Life Smart R-LS-IRTWR-1 Manuel utilisateur

Life Smart

Life Smart HT280 Manuel utilisateur

Life Smart

Life Smart LS1001HH13 Guide de démarrage rapide

Life Smart

Life Smart LS-6BPIQH-X Guide de démarrage rapide

Life Smart

Life Smart HT1193 Manuel utilisateur

Life Smart

Life Smart R-HT1156 Manuel utilisateur

Life Smart

Life Smart LS-EF450 Guide de démarrage rapide

Life Smart

Life Smart REFURBISHED R-W-19 Manuel utilisateur

Life Smart

Life Smart SH37 Manuel utilisateur

Life Smart

Life Smart LS-1000X-4M Manuel utilisateur

Life Smart

Life Smart INFRARED HEATER Guide de démarrage rapide

Life Smart

Life Smart ZCHT1040US Manuel utilisateur

Life Smart

Life Smart LS1006HH13 Guide de démarrage rapide

Life Smart

Life Smart L-SIFST-S Guide de démarrage rapide

Life Smart

Life Smart HT1167 Manuel utilisateur

Life Smart

Life Smart LS-8WQH-DLX13B Manuel utilisateur

Life Smart

Life Smart LS-4W1500-X Guide de démarrage rapide

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur