Lexmark MS810de Manuel utilisateur

Moving Guide

Before moving the printer

CAUTION—POTENTIAL INJURY: Before moving the printer, follow these guidelines to avoid personal injury or printer

damage:

•Turn off the printer, and then unplug the power cord from the electrical outlet.

•Disconnect all cords and cables from the printer.

•If two or more optional finishers are installed, then remove the finishers individually from the printer.

Notes:

–Make sure to remove the topmost finisher first.

–To remove the finisher, hold the finisher on both sides, and then lift the latches to unlock the finisher.

•If the printer does not have a caster base, then remove the optional trays.

Note: Slide the latch on the right side of the printer toward the front of the printer until it clicks into place.

Moving Guide

Page 1 of 3

•Use the handholds located on both sides of the printer to lift it.

•Make sure your fingers are not under the printer when you set it down.

•Make sure there is adequate clearance around the printer.

•Use only the power cord provided with this product or the manufacturer's authorized replacement.

Warning—Potential Damage: Damage to the printer caused by improper moving is not covered by the printer warranty.

Selecting a location for the printer

CAUTION—POTENTIAL INJURY: The printer weight is greater than 18 kg (40 lb) and requires two or more trained

personnel to lift it safely.

When selecting a location for the printer, leave enough room to open trays, covers, and doors. If you plan to install any options,

then leave enough room for them also. It is important to:

•Set up the printer near a properly grounded and easily accessible electrical outlet.

•Make sure airflow in the room meets the latest revision of the ASHRAE 62 standard or the CEN Technical Committee 156

standard.

•Provide a flat, sturdy, and stable surface.

•Keep the printer:

–Clean, dry, and free of dust.

–Away from stray staples and paper clips.

–Away from the direct airflow of air conditioners, heaters, or ventilators.

–Free from direct sunlight and humidity extremes.

•Observe the recommended temperatures and avoid fluctuations:

Ambient temperature 15.6 to 32.2°C (60 to 90°F)

Storage temperature 1 to 35°C (34 to 95°F)

Moving Guide

Page 2 of 3

•Allow the following recommended amount of space around the printer for proper ventilation:

1Right side 305 mm (12 in.)

2Front 508 mm (20 in.)

3Left side 305 mm (12 in.)

4Rear 305 mm (12 in.)

5Top 115 mm (4.5 in.)

Moving the printer to another location

The printer and its hardware options can be safely moved to another location by following these precautions:

•Any cart used to move the printer must have a surface able to support the full footprint of the printer.

•Any cart used to move the hardware options must have a surface able to support the dimensions of the hardware options.

•Keep the printer in an upright position.

•Avoid severe jarring movements.

Shipping the printer

When shipping the printer, use the original packaging or call the place of purchase for a relocation kit.

Moving Guide

Page 3 of 3

Autres manuels pour MS810de

Table des matières

Autres manuels Lexmark Imprimante

Lexmark

Lexmark W840 Manuel utilisateur

Lexmark

Lexmark W840 Manuel utilisateur

Lexmark

Lexmark MX931 Manuel utilisateur

Lexmark

Lexmark XC2100 Series Manuel utilisateur

Lexmark

Lexmark 1300 Series Manuel utilisateur

Lexmark

Lexmark C950 Series Manuel utilisateur

Lexmark

Lexmark 4227 PLUS Manuel utilisateur

Lexmark

Lexmark MB2236 Manuel utilisateur

Lexmark

Lexmark M1145 Manuel de formation

Lexmark

Lexmark 70D0000 - Z11 Color Jet Printer Manuel utilisateur

Lexmark

Lexmark C746n Manuel utilisateur

Lexmark

Lexmark Optra M410 Manuel utilisateur

Lexmark

Lexmark 11A4006 - Optra K 1220 B/W Laser Printer Manuel utilisateur

Lexmark

Lexmark T 430 Manuel utilisateur

Lexmark

Lexmark 44J0000 - J 110 Color Inkjet Printer Guide d'installation

Lexmark

Lexmark MS410 series Manuel utilisateur

Lexmark

Lexmark C52 series Manuel utilisateur

Lexmark

Lexmark 4227 - Forms Printer B/W Dot-matrix Manuel utilisateur

Lexmark

Lexmark CS510 Series Guide de configuration

Lexmark

Lexmark 2380 - Forms Printer B/W Dot-matrix Manuel utilisateur

Lexmark

Lexmark CS510 Series Manuel

Lexmark

Lexmark M52 Series Manuel utilisateur

Lexmark

Lexmark 34S0309 - E 260dtn B/W Laser Printer Manuel utilisateur

Lexmark

Lexmark C792 Family Manuel de service

Manuels Imprimante populaires d'autres marques

Canon

Canon i70 Series Manuel utilisateur

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Canon

Canon LASER SHOT LBP-1210 Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Canon

Canon PIXMA PRO-1 Series Manuel utilisateur

Canon

Canon PIXMA G3560 Guide de configuration

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Epson

Epson ET-7750 Mode d'emploi

Canon

Canon CLBR 460ps Manuel utilisateur

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Epson

Epson SC-F7100 series Manuel utilisateur

Epson

Epson Stylus C40UX Manuel utilisateur

Canon

Canon imagePASS-A2 Manuel utilisateur

Canon

Canon S820D Manuel utilisateur

IRA3D

IRA3D POETRY4 Manuel utilisateur