LELY Splendimo 320 M Manuel utilisateur
www.lely.com
SPLENDIMO M
240 / 280 / 320
M-H003.0612VT
SPLENDIMO 320 M
OPERATOR’S MANUAL
EN-1
OPERATOR’S MANUAL
SPLENDIMO M
240 / 280 / 320
Mh0030612en-tp.fm
English
SPLENDIMO®is a registered trademark. The right of exclusive use belongs to the companies of the LELY Group.
©2006. All rights reserved. Nothing of this publication may be reproduced and/or published by printing, photocopying,
microfilm or any other way without the prior written permission of LELY INDUSTRIES N.V..
EN-3
TABLE OF CONTENTS....................................................................................................page
PREFACE.......................................................................................................................5
WARRANTY CONDITIONS............................................................................................5
TYPE- AND SERIAL NUMBER OF YOUR MACHINE ...................................................5
SAFETY INSTRUCTIONS..............................................................................................6
EXPLANATION OF SAFETY DECALS ON THE MACHINE..........................................7
1 INTRODUCTION ............................................................................................................8
2 LINKAGE TO THE TRACTOR........................................................................................9
3 TRANSPORT.................................................................................................................10
4 MACHINE ADJUSTMENTS...........................................................................................11
4.1 Mowing height......................................................................................................11
4.2 Ground pressure..................................................................................................11
5 OPERATING THE SPLENDIMO®M..............................................................................12
6 DISMOUNTING FROM THE TRACTOR.......................................................................13
7 MAINTENANCE.............................................................................................................14
7.1 Maintenance after operations ..............................................................................14
7.2 Lubrication...........................................................................................................14
7.3 Intermittent maintenance .....................................................................................15
7.4 Replacement of knives ........................................................................................17
7.5 Change of oil in gearboxes..................................................................................18
7.6 Change of grease in mower elements.................................................................19
Supplements:
A REPAIRS TO THE CUTTER BAR.................................................................................20
B HYDRAULIC SCHEME..................................................................................................22
C OPTIONAL EXTRAS .....................................................................................................23
D TECHNICAL DETAILS...................................................................................................24
EN-5
PREFACE
This Operator’s Manual is meant for personnel that are operating the
machine and are responsible for its daily maintenance.
Kindly read this manual fully prior to starting work.
Such instructions as are related to your safety and/or that of
others are marked in the margin by a warning triangle with
exclamation mark. These instructions should be observed with
particular care and attention.
Instructions which may lead to serious material damage in case
of non-compliance or incorrect use are marked in the margin by
an exclamation mark.
The machine described in this manual may contain components
which do not form part of the standard equipment but are available
as optional extras.
This is not made clear in all cases, because standard specifications
may differ from country to country.
Furthermore, machines and optional extras may be adjusted to
specific regional conditions whilst they are also subject to
permanent research and innovation.
For this reason, the specifications of your machine may not be
consistent with the pictures in this manual.
WARRANTY CONDITIONS
For those parts which fail in normal operating conditions the factory
will make replacement parts available, free of charge, for a period of
12 (twelve) months from the date of purchase.
Warranty shall not apply if the instructions mentioned in this manual
have not been met, or if they have not been met completely or
correctly.
Neither shall warranty apply in case of modification of the machine
by you or third parties without our foreknowledge and/or
authorisation.
TYPE- AND SERIAL NUMBER OF YOUR
MACHINE
The type and serial number plate is fitted on the front side of the
headstock.
In case of correspondence and ordering of spare parts, kindly state
the type- and serial number of your machine.
Complete the box below with these numbers.
!
Type number
Serial number
EN-6
SAFETY INSTRUCTIONS
- Use the machine only for the purpose for which it was designed.
- Follow all prevailing safety regulations, including those laid
down in this manual and occurring on the machine.
- Operate this machine in a safe way.
- The machine should be operated by authorised persons only.
- Be alert and observe all safety precautions.
- Make sure that all safety guards and protection devices are in
place.
- Keep out of reach of moving parts.
- Stop engine, PTO and moving parts before adjusting, cleaning or
lubricating the machine.
- Take care that nobody will be within the dangerous zone while the
machine is in operation and be sure that people are kept well away
from the machine. This is especially important when working
along roads and near or on fields that are accessible to the public.
- Use always a tractor with a cab.
- Clear the field of objects that could be thrown up by the machine.
- Observe the prevailing legislation for public road transport.
- Use flashing lights or other safety signs, when required.
- Don’t stand on the machine.
- Use genuine LELY parts only.
- Remove the pressure from hydraulic systems before starting work
on them and/or before coupling/ uncoupling hydraulic hoses.
- Use protective clothing, gloves and/or safety glasses if required.
- Clean the safety decals regularly so that they can be read at all
times.
EN-7
EXPLANATION OF SAFETY DECALS ON
THE MACHINE
-Carefully read operator’s manual before handling the machine.
Observe instructions and safety rules when operating.
-Attention! Moving parts.
Stay clear of rotating machine parts.
-Danger of flying objects.
Maintain a sufficient, safe distance from the machine as long as
the tractor engine is running.
-Danger of mower knives.
Maintain a sufficient, safe distance from the machine as long as
the tractor engine is running.
- Never exceed the maximum PTO speed which is obligatory
for the machine.
- If you need to hoist the machine, only use such hoisting points
as are indicated by means of the decals.
-Attention! Moving parts.
Read the operating instruction of the PTO shaft.
Never use a PTO shaft without protection.
EN-8
1 INTRODUCTION
The LELY SPLENDIMO M mower (fig. 1) can be used for mowing
grass fields. A characteristic feature of the SPLENDIMO M mower
is the central attachment of the mower unit allowing optimum
ground contour following.
A tremendous capacity can be realised thanks to the large working
width and high forward speed (up to 15 km/h).
Mowing on slopes up to approx. 20° up and 20° down is within the
machines capability.
The cutter bar is fitted with mower discs, complete with the LELY
SPLENDIMO CLIP quick change system (fig. 2). The cutter bar is
composed of cutting units according to the modular LELY system.
These elements as well as the intermediate spacers are torqued
together by a connecting rod.
The first cutting unit is driven from the top. A springsteel shaft,
which is driven from the first cutting unit, drives the other units of
the cutter bar. Due to this configuration, only little power is
required.
The elements rotate in pairs, either to the left or right.
The SPLENDIMO M mower can be controlled with just one
hydraulic ram. Ground pressure can be adjusted in 3 positions by
repositioning the stop plate of the spring assembly.
A breakback device prevents damage to the machine if an obstacle
is hit.
1
2
Autres manuels pour Splendimo 320 M
2
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels LELY Matériel agricole
LELY
LELY Grazeway R Manuel utilisateur
LELY
LELY Attis PT 130 Manuel utilisateur
LELY
LELY Tigo 35 S Classic Manuel utilisateur
LELY
LELY Juno 100 Instructions originales
LELY
LELY COSMIX P Guide de configuration
LELY
LELY Calm View Guide de l'administrateur
LELY
LELY SPLENDIMO 240 MC Manuel utilisateur
LELY
LELY HIBISCUS 1015 Profi Manuel utilisateur
LELY
LELY HIBISCUS 455 Manuel utilisateur
LELY
LELY Juno Manuel utilisateur
LELY
LELY Splendimo 320 M Manuel utilisateur
LELY
LELY Juno 100 Instructions originales
LELY
LELY HIBISCUS 725 Master Manuel utilisateur
LELY
LELY LOTUS 1325 Manuel utilisateur
LELY
LELY HIBISCUS 765 SD Vario Manuel utilisateur
LELY
LELY Splendimo 550 P Manuel utilisateur
LELY
LELY HIBISCUS 655 SD Manuel utilisateur
LELY
LELY Hibiscus 725 CD Classic Manuel utilisateur
LELY
LELY LELYTERRA 400-35H Manuel utilisateur
LELY
LELY SPLENDIMO TRIPLO 920 C Manuel utilisateur
Manuels Matériel agricole populaires d'autres marques
GSi
GSi PNEG-2314 Manuel utilisateur
Checchi & Magli
Checchi & Magli TEXDRIVE Manuel utilisateur
Amazone
Amazone Cenius 4003-2TX Manuel utilisateur
MASSEY FERGUSON
MASSEY FERGUSON MF 9313S Manuel utilisateur
Cima
Cima BLITZ Instructions d'utilisation et d'entretien
Amazone
Amazone CombiDisc 3000 Instructions d'installation
