LEAP Electronics LEAPER-56 Manuel utilisateur
LEAPER-56
Universal IC Writer
User's Manual
Chapter 1 Product escription .......................................
1-1 Introduction
1-2 Safety Information
1-3 Precautions
1-4 Operating System, Hardware Re uirement
1-5 Accessories
Chapter 2 Product Installation ........................................
2-1 Hardware Installation
2-2 Software Installation
2-3 Driver Installation
Chapter 3 IC Insertion ..........................................................
3-1 General IC Insert (DIP package)
3-2 Special IC Insert Via Adapter (Special package)
Chapter 4 Software Operating .........................................
4-1 Software Main Screen
4-1-1 IC Information Column
4-1-2 Message Column
4-1-3 Statics of Programming Result Column
4-1-4 Other Operating Buttons
4-2 Device Select/Project
4-2-1 Device Select
4-2-2 Device Selected Record
4-2-3 Project
4-3 File Load
4-3-1 Load File Path
4-3-2 File Format
4-3-3 Source Select
4-3-4 Destination Select
4-3-5“Fill Unused With”Function
4-4 Edit
4-4-1 Display Mode (8 Bits/16 Bits)
4-4-2 View/Edit Mode
4-5 Option Setting
4-5-1 General System Setting
4-5-2 Device Option
1
4
8
9
Universal IC Writer User's Manual
Contents
Universal IC Writer User's Manual
4-6 Save
4-6-1 Save File Path
4-6-2 Save File Format
4-6-3 Main Range Select Saving
4-7 Device Processing Procedure
4-7-1 Read
4-7-2 Data Confirm
4-7-3 Erase
4-7-4 Blank Check
4-7-5 Program
4-7-6 Verify
4-7-7 Protect
4-7-8 ALL RUN
4-7-9 Condition Display
Chapter 5 Simple Operating Practice ..........................
e.g.1.Programming the MCU from data of computer, and adding
protection on IC.
e.g.2.Reading internal memory data of the IC, and saving it by
Binary Format.
e.g.3.Using system's self detecting function to detect hardware
of programmer.
Chapter 6 Troubleshooting ................................................
Contents
18
26
Universal IC Writer User's Manual
1
Chapter 1 Product escription
1-1 Introduction
Due to the development of IC has been changed with each passing days. The
memory capacity and operating fre uency of IC has not been in support of traditional
programmers.
In order to shorten the waiting time of programming and let IC can be operated on
accurate fre uency, we takes ICT technology into the Universal Programmer. This means
the bandwidth of test signal increases to over 75MHz. Besides, the phase deviation is
only in ±2.2nS.
However it is not enough for users. The most valuable advantage is that we minimize the
size to put in the pocket! It is portable and connectable easily by USB cable. Moreover,
operating with our uni ue software can make all the users have the best experience on
programming uality and efficiency.
1-2 Safety Information
All the operations, maintenance and repair services are re uired to follow below safety
information. We do not take responsibility for unexpected problem by misusing the
e uipment.
1. The programmer must be used standard accessory Y-USB cable, while connecting
to computer. Besides,checking both USB plugs are connected to the computer
and confirm the USB power can let product operate normally. If the computer is
connected through USB Hub it will need another power adapter. (+5V/1A above)
2. Do not operate the product near flammable gases or fire.
High-temperature and humid environment are also prohibited.
3. Do not remove the product's case to operate, adjust or replace internal parts. Avoiding
e uipment's malfunction and Unnecessary risk.
4. Sockets or adapters are consumables. The life time is depend on the fre uency of
using from the supplier's product specification. If customer's using time is more than
the specification, the sockets will have bad connect. This will result in highly poor
burning rate or burning failure.
5. When Using this product as mass production or production for master tape,please take
the complete testing for treated samples which is assembled on practical products.
All the risks attributed to product using or software operating are undertaken by the
user.
※ This manual is for reference and preservation of consumers. Product specifications and
manuals will not be notified when modifying.
※ The company or trademarks mentioned in this manual are the property of them.
Universal IC Writer User's Manual
2
1-3 Precautions
1. When you deal with your IC through programmer, the programmer will access it on high
fre uency signal. For the uality and yield rate of the IC, you must note following:
a.While the IC is in processing action (including read / verify / programming / erase /
blank check ... etc) Do not use hands or other items to touch the IC on socket. When
inserting IC, please take notice on electrostatic protection treatment for operators.
b.If you need other adapters for kinds of IC-package(for example, TSOP, PLCC, TQFP,
QFN .. etc.). Please buy good uality ones, or ask your supplier to purchase that.
Do not use inferior uality of the adapters, or welding by yourself. Because of the
programmer processing the IC with high-fre uency signal. If the external adapters are
poor uality. We will be unable to ensure the IC processing uality!
2.When connecting programmer on the computer, please be sure to note the following:
a.Be sure to use the standard accessory with Y-USB cable. And two USB plugs are
connected to the computer. Ordinary USB cable can not ensure the uality and
stability when programming.
b.The programmer at the beginning of implementing computer software, it will check the
power supply by USB hub. If the power supply is not enough, it will pop up a warning
message below. You can use the standard Y-USB Cable two plugs connecting
to the computer, or changing to other USB socket. If still no improvement, it may your
computer USB power supply be limited.
You can use an external USB Hub and Power Adapter (5V, 1A) to improve it.
On the warning message window, you can press the "Reset" key to re-test. you can
also press the "Cancel" button to skip the power detection. However by doing so, the
system can not guarantee 100% regular working.
Universal IC Writer User's Manual
3
1-4 Operating System, Hardware Re uirement
Operating System：Windows XP / Vista / Windows 7 (32bits / 64bits)
CPU：PC / Pentium IV or above
Memory：1 GB RAM or above
Hard disk space：500 MB or more (main program)
Data buffer with 1GB or more
(depending on device capacity)
Monitor Resolution: 800 x 600 pixels or above
Interface: USB 2.0 High Speed
Power Re uirements: 2 groups of USB Port providing
+5 V power supply
Power Consumption: 4W
Dimensions: 130 (L) x 90 (depth) x 20 (high) mm
Note: Height does not include Socket
Weight: 290g
Operating temperature: +5 ℃ +45 ℃
1-5 Accessories
Main Unit ......................................................... 1
Special Y-USB cable ........................................ 1
CD-ROM (to install software and manual) ........ 1
Universal IC Writer User's Manual
4
Chapter 2 Product Installation
2-1 Hardware Installation
1. Using standard accessory with Y-USB cable and connecting two USB plugs to
the computer. If you use the USB Hub, please connect it to the Power Adapter
(5V), and remove other power consumption USB product on the Hub. Such as
an external hard drive...and so on.
2. Programmers connected to the computer without installing the driver at the first time,
the blue LED on machine will not flash or light.
This is normal. After installing the driver and connecting to the computer, the
programmers' LED will flash 2 times then turn off.
Until the software is operated it will be light steadily. The LED will automatically turn off
after the software shut down.
2-2 Software Installation
1.Please note that: When installing the software on your computer, the operating
system will require "administrator" permission. If you have no permission, It
may result in unsuccessful installation.
2.Insert the CD into the computer, and the installation screen will automatically pop up. If
there's no installation screen, please install through "My Computer" into the CD-ROM
drive and executive AUTORUN.EXE
3.Pressing the "Install" button to start installing after entering installation path and name
of start menu. Finally press the "Finish" to finish the installation.
4. Then click the driver's installation files in CD (Or download the latest updates on the
internet).And updating IC database.
Universal IC Writer User's Manual
5
2-3 Driver Installation
1.Please install the software on your computer. And then connecting the programmer to
computer through the Y-USB cable. Starting driver installation.
2.For the first time when installing the hardware. There will be a message about finding
a new device, and then asking install the driver. Please follow the following steps to
install.
Check this item
Universal IC Writer User's Manual
6
3.The path is set to "\ Universal IC Writer II \ USBDrv" list
(The above options need to be checked.)
Choose to continue the installation
Table des matières
Autres manuels LEAP Electronics Matériel informatique
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
