Larson Electronics APM-GL20004 Manuel utilisateur

APM-GL20004

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 2

Golight LED Spotlight w/Telescoping Pole

Instruction Manual

Do not attempt operation until you are familiar with all warnings, precautions, and procedures outlined within this

instruction sheet. Read carefully before operating. Retain these instructions for future reference.

WARNING:

•KEEP PLUGS AND RECEPTACLES DRY.

•DO NOT TOUCH HOT LENS OR ENCLOSURE.

•DO NOT REMAIN IN LIGHT IF SKIN FEELS WARM.

•DO NOT LOOK DIRECTLY AT LIGHTED LAMP.

•KEEP LAMP AWAY FROM MATERIALS THAT MAY BURN.

USING THE TRIPOD

1. Utilize a pre-existing pole mount or purchase a TPM-MOUNT.

2. Place telescoping pole in mount and secure.

3. Place LED Golight lamp over the top pole and tighten hand screw.

4. Loosen the black adjustment knob for each adjustment sleeve to extend the

tripod. Start with the top section when lifting.

5. Tighten adjustment knob once desired height is achieved.

VEHICLE WIRING

•Connect cord to light via the deutsch connector and coil cord to

Voltage: 12V DC cigarette plug receptacle.

A single 2-pin Deutsch IPD / LADD DT04-2P connector allows for quick connections to

and from spotlight. Plug the Deutsch Connector into the the light, and connect other

end to a compatible power source (12V DC). For cords supplied with flying leads,

attach the positive and negative leads to their respective polarities on your power

source. For cords with cigarette plugs, connect to matching receptacle.

LED OPERATION

Wireless Dash Control

BATTERY INSTALLATION AND REMOVAL FOR TRANSMITTER

Remove battery cover: for wireless hand-held transmitter, remove Phillips head screw

to remove cover. With battery compartment now exposed, insert batteries according to

the correct polarity or gently remove batteries by grabbing the positive end and lifting

up.

PROGRAMMABLE REMOTE INSTRUCTIONS

The LED spotlight is controlled with a programmable remote with 2187 different

channels. This feature allows you the freedom to change the channel selection, and

the receiver relearns the new selection. This light has been pre-programmed at the

factory, and it is not necessary to re-program the transmitter, unless you experience

outside interference.

To program transmitter:

1. IMPORTANT: Disconnect power.

2. Remove battery cover from remote control.

3. Set the 7 dip switches to a selection of your choice. There are 3 positions on each; positive, negative and neutral. Use

a small screwdriver and select a position for each dip switch. *Please note that the orientation of the +/- switch

positions may vary among different models of wireless remote controls.

4. Insert both GP 23A 12V batteries. Be sure batteries have adequate charge.

5. Replace battery cover.

a. Depress the on/off button and hold it down. Red LED will light.

ADJUSTMENT

POINTS

DEUTSCH

CONNECTOR

LED

LAMP

APM-GL20004

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

2of 2

b. While holding the on/off button down, reinstall the power (replace fuse or connect vehicle battery).

c. Keep on/off button depressed for 5-6 seconds, and then release. The light should now be programmed.

OPERATION OF SPOTLIGHT

1. Using the remote control, turn on the light by depressing the on/ off button.

2. With the joystick on the dash control, rotate your light to the desired location.

3. The speed of the light rotation can be controlled by depressing the fast/slow button one time and by depressing

it again to restore the original speed.

4. The hard wired dash control will be backlit when the bulb is illuminated.

USAGE:

This light is intended for off-road and utility use only

This light is intended to be mounted outside the vehicle while in use

This light may only be disassembled and repaired by an authorized representative

MISUSE:

This light is not approved for road or highway use

This light is not approved for underwater use

This light is not approved for inverted mounting

This light is not approved for use inside a vehicle or enclosure and power should be disconnected prior to

placing the light in such circumstance

This light may be damaged if operated in icing conditions

This light may only be dismantled by an authorized representative

Any violation of the above referenced misuses will be considered grounds for warranty refusal

USE AND CARE

Always check damaged or worn out parts before using the work light. Broken parts will affect operation. When not in use,

store work light in a secure place out of the reach of children. Inspect it for good working condition prior to storage and

before re-use.

MAINTENANCE

Maintain your work light. It is recommended that the general condition of any work light be examined before it is used.

Keep your work light in good repair by adopting a program of conscientious repair and maintenance. Have necessary

repairs made by qualified service personnel.

IMPORTANT SAFETY INFORMATION



This symbol is to alert you to important operating or servicing instructions that appear in your instructions. Always follow

basic safety precautions when using this product to reduce the risk of injury, fire or electric shock.

This light is for off road and utility use only. It is not designed for road use as a driving light.

The GL-30204 complies with Part. 15.105 of the FCC Rules. This equipment has been tested and found to comply with the limits for

a Class B digital device. These limits are designed to provide reasonable protection against harmful interference in a residential

installation.

FCC RULE Part. 15.21 - Changes or modifications made by the user not expressly approved by Larson Electronics, LLC for

compliance could void the user’s authority to operate the equipment.

THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR

INSTALLATION REQUIREMENTS. SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE

REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT SALES@LARSONELECTRONICS.COM OR BY PHONE AT 1-800-

369-6671 FOR FURTHER ASSISTANCE.

PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.

Table des matières

Autres manuels Larson Electronics Mettre en lumière

Larson Electronics

Larson Electronics GL-4600-XD Manuel

Larson Electronics

Larson Electronics RL-85-3W1 Manuel utilisateur

Larson Electronics

Larson Electronics LED10W-1SCB Manuel utilisateur

Larson Electronics

Larson Electronics HUL-18 Manuel utilisateur

Larson Electronics

Larson Electronics RL-14 Manuel utilisateur

Larson Electronics

Larson Electronics HL-85-CPR-MS Manuel utilisateur

Larson Electronics

Larson Electronics GAU-LTL-500W-LED-IR Manuel utilisateur

Larson Electronics

Larson Electronics GL-8130-M Manuel utilisateur

Larson Electronics

Larson Electronics GL-30004-S-E Manuel

Larson Electronics

Larson Electronics HAL-RA-48-6L-LED Manuel utilisateur

Larson Electronics

Larson Electronics Golight Radioray GL-2081-M Manuel

Larson Electronics

Larson Electronics RML-8 Manuel utilisateur

Larson Electronics

Larson Electronics LE-224-LED Manuel utilisateur

Larson Electronics

Larson Electronics LE-217 Manuel utilisateur

Larson Electronics

Larson Electronics LEDWL 1227 Series Manuel

Larson Electronics

Larson Electronics The LE-9 Series Manuel utilisateur

Larson Electronics

Larson Electronics GL-3610-S-E Manuel

Larson Electronics

Larson Electronics HUL-LED25WRE-CPR Manuel utilisateur

Larson Electronics

Larson Electronics Golight GL-3000-24-M Manuel utilisateur

Larson Electronics

Larson Electronics Golight Radioray GL-2051GT Manuel utilisateur

Larson Electronics

Larson Electronics RL-85-10W1 Manuel utilisateur

Larson Electronics

Larson Electronics GL-3110-S-12-E Manuel

Larson Electronics

Larson Electronics Golight Stryker GL-3049-P Manuel

Larson Electronics

Larson Electronics Golight RadioRay GL-7 GT Series Manuel utilisateur

Manuels Mettre en lumière populaires d'autres marques

Guangzhou Yinhe Lighting&Sound Equipment Factory

Guangzhou Yinhe Lighting&Sound Equipment Factory NE-204 Manuel utilisateur

LIVARNO home

LIVARNO home 375304 2101 Instructions originales

Cameo

Cameo CLQS40WW Manuel utilisateur

Leviton

Leviton Ellipsoid 5/50 Manuel utilisateur

Monacor

Monacor img Stage Line PARL-56PDX/CR Manuel utilisateur

Vector

Vector SL3AKV Manuel utilisateur

Quantum

Quantum Q262 Manuel d'exploitation

Philips

Philips Vari-lite VL3015LT Manuel utilisateur

EUROSPOT

EUROSPOT C51 Manuel utilisateur

DTS

DTS MINI BRICK ARC Manuel utilisateur

Federal Signal Corporation

Federal Signal Corporation VISIBEAM II Manuel

ACME

ACME LED-MS350B Manuel utilisateur

EuroLite

EuroLite Akku flat light 1 Manuel utilisateur

Commercial Electric

Commercial Electric SPTM-1401 Manuel utilisateur

Vision & Control

Vision & Control SLB-500-W5K7-P-SL Manuel utilisateur

Teknik

Teknik FLEXI Manuel utilisateur

Craftsman

Craftsman CMXLSB10 Manuel utilisateur

EuroLite

EuroLite LED SLS-144 UV Floor Spot Manuel utilisateur