Lanzar EV 254 Manuel utilisateur
Congratulations on your purchase of a Lanzar EVOLUTION amplifier. You have purchased a quality product designed
and engineered to give you many years of uncompromised musical service. EVOLUTION amplifiers are designed with
the latest technology available, incorporating a DC to DC Switching Power Supply, which provides headroom for
even the most demanding peaks and dynamic ranges found on modern CD's and recordings.
Features
MOSFET switches maintainrated power overa wide rangeof battery voltages
2 Ohm StableStereo operation
Variable input levelcontrols for eachpair of channels
Variable high andlow pass crossovercontrols
Thermal and speakershort protection circuitry
Power and ProtectionLED indicators
Bass Boost Circuitry
Stereo, Bridge Modeand Tri-Mode SystemApplication Compatible
Nickel plated power,RCA and speakerconnectors
High-efficiency, heavy aluminumheatsink
PWM(Pulse-Width-Modulated) System
Bass Boost Remotecontrol
9.Power & Protection Indicators- Provide instantinformation onstatus of amplifier,
including short-circuitand thermaloverload alerts.
7.Bridged Mode
8.Bass Boost Remote Control Input
2. Line Out RCA Jacks - The LINEOUT allowsyou to build multipleamplifier systemswith outhaving touse splittercords
to distributethe signal.Now it issimple a matter of bringing oneset of RCAs into thefirst amplifier,
then usingthe line outRCA jacksas the feedto the nextamplifier.
1. Input RCA Jacks -These inputsare for signal cablesfrom thesource. Alwaysuse highquality shieldedRCA cables.
3. Level Control- Enables thematching ofinput levelsto the output levelsfrom thehead unit(orother signalsource).
5.Variable Low Pass Filter-When Crossover Mode Selector is in Low Pass Mode, this control limits the frequencies
which will be distributed to the speakers to those below the value to which this is set within the range 50~500Hz.
(MONO AND EV594 SUB@1CH,WITHIN THE RANEG 50 - 250Hz.)
10.Variable Bass Boost Control- 0~18dB @60Hz FIX.
11.High Inputs- Accepts speakerlevel inputsfrom headunits thatdo not line level (RCA) outputs.
12.Crossover mode selector - Determines themode of built-in crossover:low pass(permitsonly low frequency signals
to pass tospeakers), highpass(permits onlyhigh frequencysignals topass to speakers),or flat.
6.Variable High Pass Filter-When Crossover Mode Selector is in High Pass Mode, this control limits the frequencies
which will be distributed to the speakers to those below the value to which this is set within the range 50~500Hz.
(THIS IS MONO AMP SUBSONIC FILTER WITHIN THE RANGE 15 - 45Hz)
13.Speaker Temimal.
4.Phase Shift control - Allows youto change the phase of your subwooferfrom 0 to180 degrees
to help compensate fortiming differencesbetween drivers.
Frequency Response
S/N Ratio
Channel Separation
Low Pass Filter
High Pass Filter
Bass Boost Control
Peak at 4 Ohm Bridged
T.H.D
RMS at 4 Ohms
Input Sensitivity
Fuse(s)
Dimensions:WxHxL(inches)
>100dB
>60dB
200mV~6V
Peak at 4 Ohms
RMS at 4 Ohm Bridged
800W x 2
800W x 1
1600W x 1
400W x 2
<0.05%
20Ax2
8.97" x 2..41" x 11.02"
50Hz~500Hz
50Hz~500Hz
15Hz~40KHz
>100dB
>60dB
1600W x 2
1600W x 1
3200W x 1
800W x 2
<0.05%
30Ax3
8.97" x 2..41" x 14.17"
50Hz~500Hz
50Hz~500Hz
15Hz~40KHz
>100dB
>60dB
500W x 4
500W x 2
1000W x 2
250W x 4
<0.05%
20Ax2
8.97" x 2..41" x 12.83"
50Hz~500Hz
50Hz~500Hz
15Hz~40KHz
>100dB
>60dB
750W x 4
750W x 2
1500W x 2
375W x 4
<0.05%
25Ax3
8.97" x 2..41" x 15.19"
50Hz~500Hz
50Hz~500Hz
15Hz~40KHz
>100dB
>60dB
1000W x 4
1000W x 2
2000W x 2
500W x 4
<0.05%
40Ax3
8.97" x 2..41" x 17.16"
50Hz~500Hz
50Hz~500Hz
15Hz~40KHz
Low:200mV~6V
High:400mV ~12V
0 - 18dB @ 60Hz FIX 0 - 18dB @ 60Hz FIX
Low:200mV~6V
High:400mV ~12V Low:200mV~6V
High:400mV ~12V Low:200mV~6V
High:400mV ~12V
0 - 18dB @ 60Hz FIX
Frequency Response
S/N Ratio
Channel Separation
Low Pass Filter
High Pass Filter
Bass Boost Control
Peak at 1 Ohm
T.H.D
RMS at 4 Ohms
Input Sensitivity
Fuse(s)
Dimensions:WxHxL(inches)
>85dB
1000W x 1
2000W x 1
4000W x 1
500W x 1
<0.05%
25Ax3
8.97" x 2..41" x 14.17"
50Hz~250Hz
(Subsonic@1CH) :15Hz ~ 45Hz
15Hz~250Hz
Low:200mV~6V
High:400mV ~12V
0 - 18dB @ 60Hz FIX
RMS at 2 Ohms
RMS at 1 Ohm
>100dB
312W x 4 RMS at 4 Ohms & 750W x 1 RMS at 2 Ohms
<0.05%
40Ax3
8.97" x 2..41" x 17.16"
50Hz~500Hz / 50Hz~250Hz
50Hz~500Hz
15Hz-40KHz/ (SUB@1CH) : 15Hz - 250Hz
Low:200mV~6V
High:400mV ~12V
625W x 4 Peak at 4 Ohms & 1500W x 1 Peak at 2 Ohms
Tri-Mode 625W x 2 RMS at 2 Ohms Bridged & 1000W x 1 RMS at 1 Ohm
Tri-Mode 1250W x 2 Peak at 2 Ohms Bridged & 1500W x 1 Peak at 1 Ohm
>60dB
(SUB@1CH) :0 -18dB @ 60HzFIX
Ce manuel convient aux modèles suivants
6
Table des matières
Autres manuels Lanzar Amplificateur
Lanzar
Lanzar Mariner AQA430SL Manuel utilisateur
Lanzar
Lanzar OPTI Class-D Manuel utilisateur
Lanzar
Lanzar MXA214 Manuel utilisateur
Lanzar
Lanzar MAXP 1055D Manuel utilisateur
Lanzar
Lanzar MXA214 Manuel utilisateur
Lanzar
Lanzar WDN2000.1D Manuel utilisateur
Lanzar
Lanzar Heritage HTGBD1 Manuel utilisateur
Lanzar
Lanzar MAX PRO MAXP 1200N Manuel utilisateur
Lanzar
Lanzar HTG889 Manuel utilisateur
Lanzar
Lanzar Distinct DCT202 Manuel utilisateur
Lanzar
Lanzar MNX260 Manuel utilisateur
Lanzar
Lanzar OPTIDRIVE OPTIMC90 Manuel utilisateur
Lanzar
Lanzar MAXP 2760N Manuel utilisateur
Lanzar
Lanzar HTG137 Manuel utilisateur
Lanzar
Lanzar OPTI 1200HC Manuel utilisateur
Lanzar
Lanzar HERITAGE HTG 214 Manuel utilisateur
Lanzar
Lanzar Vibe Manuel utilisateur
Lanzar
Lanzar Vector VCT-2110 Manuel utilisateur
Lanzar
Lanzar Distinct DCT202 Manuel utilisateur
Lanzar
Lanzar OPTI Class-D Manuel utilisateur
