Lanzar Distinct DCT202 Manuel utilisateur
Full FET Class AB Amplifier
MOSFET switches
maintain rated power over a wide range of
battery voltages
PWM(Pulse-Width-Modulated) System.
2 Ohm Stable Stereo operation
Stereo, Bridge Mode and Tri-Mode System Application Compatible
Variable input level controls for each pair of channels
Variable high and low pass crossover controls
Thermal and speaker short protection circuitry
Power and Protection LED indicators
Bass Boost Circuitry
Nickel plated power, RCA and speaker connectors
High-efficiency, heavy aluminum heatsink
Congratulations on your purchase of a LANZAR amplifier. You have
purchased a quality product designed and engineered to give you
many years of un compromised musical service. LANZAR amplifiers
are designed with the latest technology available, incorporating
a DC to DC Switching Power Supply, which provides headroom for
even the most demanding peaks and dynamic ranges found on
modern CD's and recordings.
When Crossover Mode Selector is in
Low Pass Mode, this control limits the
frequencies which will be distributed to
the speakers to those below the value
to which this is set within the range
50 Hz - 500 Hz.
LOW
PASS
FILTER
When Crossover Mode Selector is in High Pass
Mode, this control limits the frequencies which will
be distributed to the speakers to those above the
value to which this is set within the range
50 Hz - 500 Hz.
HIGH
PASS
FILTER
Determines the mode of built-in crossover:
low pass(permits only low frequency signals to
pass to speakers), high pass (permits only high
frequency signals to pass to speakers), or flat.
CROSSOVER
MODE
SELECTOR
Provide instant information on status of amplifier,
including short-circuit and thermal overload alerts.
POWER &
PROTECTION INDICATORS
Enables the matching of input
levels to the output levels from
the head unit(or other signal
source).
INPUT
LEVEL
CONTROL
Increases sound level in lower
frequencies by 18dB.
BASS
BOOST
CONTROL
INPUT RCAJACKS
These inputs arefor signal
cables from thesource.
Always use highquality
shielded RCAcables.
LINE OUTRCA
JACKS
The LINE OUTallows you to
build multiple amplifiersystems
with out havingto use splitter
cords to distributethe signal.
Now it issimple a matterof
bringing one setof RCAs into
the first amplifier, then using
the line outRCA jacksas the
feed to thenext amplifier.
SPEAKER TERMINAL.
20A x2
25A x2
25A x3
DCT202
DCT252
DCT282
MODEL FUSES
When Crossover Mode Selector is in High and
Low Pass Mode, this control limits the frequencies
which will be distributed to the speakers to those
above the value to which this is set within the range
50 Hz - 500 Hz.
HIGH & LOW PASS
FILTER
Determines the mode of built-in crossover:
low pass(permits only low frequency signals to
pass to speakers), high pass (permits only high
frequency signals to pass to speakers), or flat.
CROSSOVER
MODE
SELECTOR
Provide instant information on status of amplifier,
including short-circuit and thermal overload alerts.
POWER &
PROTECTION INDICATORS
Enables the matching of input
levels to the output levels from
the head unit(or other signal
source).
INPUT
LEVEL
CONTROL
Increases sound level in lower
frequencies by 18dB.
BASS
BOOST
CONTROL
INPUT RCAJACKS
These inputs arefor signal
cables from thesource.
Always use highquality
shielded RCAcables.
LINE OUTRCA
JACKS
The LINE OUTallows you to
build multiple amplifiersystems
with out havingto use splitter
cords to distributethe signal.
Now it issimple a matterof
bringing one setof RCAs into
the first amplifier, then using
the line outRCA jacksas the
feed to thenext amplifier.
SPEAKER TERMINAL.
INPUT RCAJACKS
INPUT
LEVEL
CONTROL
HIGH & LOW PASS
FILTER
CROSSOVER
MODE
SELECTOR
Frequency Response
Input Sensitivity
S/N Ratio
Channel Separation
Low Pass Filter
Bass Boost Control
Dimensions(inches)
Fuse(s)
RMS at 2Ohms
At 4 OhmsBridged
Speaker Impedance
T.H.D4 Ohms Power
Peak at 4Ohms
10Hz ~40kHz
>90dB
>65dB
50Hz~500Hz
0 ~+18dB
(60 Hz fixed)
8.66"x2.15"x9.45"
20A x
2
950W x 2
2000W x 1
2 Ohm
0.5%
1000W x 2
100mV~4V
High Pass Filter 50Hz~500Hz
10Hz ~40kHz
>90dB
>65dB
50Hz~500Hz
0 ~+18dB
(60 Hz fixed)
8.66"x2.15"x11.42"
25A x
2
1050W x 2
3000W x 1
2 Ohm
0.5%
1500W x 2
100mV~4V
50Hz~500Hz
10Hz ~40kHz
>90dB
>65dB
50Hz~500Hz
0 ~+18dB
(60 Hz fixed)
8.66"x2.15"x15.35"
25 x 3
1400W x 2
4000W x 1
2 Ohm
0.5%
2000W x 2
100mV~4V
50Hz~500Hz
10Hz ~40kHz
>90dB
>65dB
50Hz~500Hz
0 ~+18dB
(60 Hz fixed)
8.66"x2.15"x13.38"
30A x
2
750W x 4
2000W x 2
2 Ohm
0.5%
1000W x 4
100mV~4V
50Hz~500Hz
1. Find a suitable location in the vehicle to mount the amplifier.
2. Make sure there is sufficient air flow around the intended mounting location.
3. Bolt the amplifier to the mounting surface.
4. Connect the power ground terminal to the nearest point on the chassis of the car.
Keep this ground wire less than one meter (39") in length. Use 4 gauge or 0 gauge wire.
5. Connect the remote terminal to the remote output of the head unit using 14 gauge.
6. Connect an empty fuse holder within 300mm (12") of the battery and 4 gauge
or larger high quality cable from this fuse to the amplifier location.
7. Make sure there is no fuse in this fuse holder. Then make the connection to the "BATT"
connection on the amplifier.
8. If multiple amplifiers are being used, use cables (each with its own fuse at the battery)
or a #0 or a #2 cable from the fuse holder at the battery to a distribution block at or
near the amplifier's location.
9. Connect all line inputs and outputs using high-quality RCA-RCA cables.
10. Insert fuse(s) at the battery fuse holder(s).
11. Recheck all connections before powering up.
12. Set all level controls to their least sensitive positions and set all crossover controls,
switches, etc. to the desired frequency or position.
13. Once the system is powered up, set the volume control on the head unit to about the
2 o'clock position, and then set all the amplifiers' level controls for maximum output level.
14. Further fine tuning of the various controls may be necessary to obtain the desired
results.
LEFT
SPEAKER
RIGHT
SPEAKER
SPEAKER
IMPEDANCE
2~4 OHM
TO OUTPUT
FROM HEAT UNIT
2channel
stereo configuration
20A x2
25A x2
25A x3
DCT202
DCT252
DCT282
MODEL FUSES
TO CAR
STEREO
AUTO ANTENNA
FUSE
SPEAKER
IMPEDANCE
4~8 OHM
2channel
bridged mode configuration
TO OUTPUT
FROM HEAT UNIT
20A x2
25A x2
25A x3
DCT202
DCT252
DCT282
MODEL FUSES
TO CAR
STEREO
AUTO ANTENNA
FUSE
TO CAR
STEREO
AUTO ANTENNA
SPEAKER
IMPEDANCE
4~8 OHM
LEFT
SPEAKER
2channel
tri-mode configuration
TO OUTPUT
FROM HEAT UNIT
20A x2
25A x2
25A x3
DCT202
DCT252
DCT282
MODEL FUSES
RIGHT
SPEAKER
FUSE
4channel
stereo configuration
TO OUTPUT
FROM HEAT UNIT
TO CAR
STEREO
AUTO ANTENNA
4CH
SPEAKER
3CH
SPEAKER
2CH
SPEAKER
1CH
SPEAKER
FUSE
Autres manuels pour Distinct DCT202
1
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels Lanzar Amplificateur
Lanzar
Lanzar Heritage HTGBD1 Manuel utilisateur
Lanzar
Lanzar MAX PRO MAXP 1200N Manuel utilisateur
Lanzar
Lanzar WDN2000.1D Manuel utilisateur
Lanzar
Lanzar OPTI Class-D Manuel utilisateur
Lanzar
Lanzar vibe4000D Manuel utilisateur
Lanzar
Lanzar MXA214 Manuel utilisateur
Lanzar
Lanzar MXA214 Manuel utilisateur
Lanzar
Lanzar MNX260 Manuel utilisateur
Lanzar
Lanzar Vibe Manuel utilisateur
Lanzar
Lanzar OPTI 1200HC Manuel utilisateur
Lanzar
Lanzar Opti 1000D Manuel utilisateur
Lanzar
Lanzar Vector VCT-2110 Manuel utilisateur
Lanzar
Lanzar OPTI Class-D Manuel utilisateur
Lanzar
Lanzar VIBE211 Manuel utilisateur
Lanzar
Lanzar EV 254 Manuel utilisateur
Lanzar
Lanzar HTG137 Manuel utilisateur
Lanzar
Lanzar LANZAR VIBE X6 Manuel du propriétaire
Lanzar
Lanzar HTG 888 Manuel utilisateur
Lanzar
Lanzar OPTIDRIVE OPTIMC90 Manuel utilisateur
Lanzar
Lanzar LANZAR MAX MXA1600 Manuel utilisateur
