Lantronix XPico Manuel utilisateur

Part Number 900-623

Revision D January 2018

xPico Development Kit

Quick Start Guide

xPico Development Kit Quick Start Guide 2

Intellectual Property

publication may be transmitted or reproduced in any form or by any means

without the written permission of Lantronix.

Lantronix and DeviceLinx are registered trademarks of Lantronix, Inc. xPico and

DeviceInstaller are trademarks of Lantronix, Inc.

Patented: http://patents.lantronix.com; additional patents pending.

UNIX is a registered trademark of The Open Group. Windows is a trademark of

Microsoft Corporation. All other trademarks and trade names are the property of

their respective holders.

Warranty

For details on the Lantronix warranty replacement policy, please go to our Web

site at www.lantronix.com/support/warranty.

Contacts

Lantronix, Inc.

7535 Irvine Center Drive

Suite 100

Irvine, CA 92618, USA

Toll Free: 800-526-8766

Phone:949-453-3990

Fax: 949-453-3995

Technical Support Online: www.lantronix.com/support

Sales Offices

For a current list of our domestic and international sales offices, go to the

Lantronix web site at www.lantronix.com/about/contact.

Revision History

Date

Rev.

Comments

April 2012

Initial release.

August 2012

Updated for the new revision of the evaluation board.

March 2013

Updated for the new xPico Modbus module.

January 2018

Updated enhanced password information.

xPico Development Kit Quick Start Guide 3

Table of Contents

Table of Contents_______________________________________________________ 3

Introduction ___________________________________________________________ 4

Development Kit Contents ________________________________________________ 4

What You Need to Know _________________________________________________ 4

Hardware Address ___________________________________________________ 4

IP Address _________________________________________________________ 4

Connecting an xPico Module — Network Method ______________________________ 5

Connecting an xPico Module — Serial Method ________________________________ 6

Install DeviceInstaller ____________________________________________________ 6

Assign an IP Address____________________________________________________ 7

Configure Your xPico Device ______________________________________________ 9

xPico Module _______________________________________________________ 9

xPico-IAP Module____________________________________________________ 9

xPico Development Kit Quick Start Guide 4

Introduction

Thank you for purchasing the xPico Development Kit from Lantronix.

This Quick Start guide describes the procedures for initial connection to the xPico

module through either a network connection or serial port.

Once a connection is established you can use the WebManager or Setup Mode

for configuration and control.

Development Kit Contents

Note: The xPico Evaluation Board is designed to work with the family of xPico

serial to Ethernet modules. Please ensure that you have the correct module for

your needs. The Evaluation Kit comes with the standard xPico serial to Ethernet

device. If you wish to use the xPico-IAP then please ensure that you have the

XPC10010MS-01 or later module.

♦xPico Module

♦xPico Evaluation Board

♦Two xPico Mounting Quick Clips (one installed)

♦Sample 40-pin Mating Connector

♦5V Wall-mount Power Supply AC/DC, 1A

♦RS-232, DB9F/F, 10 ft, Null Modem Cable

♦Ethernet Cable 10 ft

For the latest revision of this product document, please check our online

documentation at www.lantronix.com/support/documentation.

What You Need to Know

Hardware Address

You need to know the unit hardware address (also known as MAC address) to

identify the unit in the Device Installer search list. It is on the product label in the

format: 00-80-A3-XX-XX-XX, where the XXs are unique numbers assigned to

the product.

Hardware Address: 00-80-A3-_____-_____-_____

IP Address

Your xPico will need a unique IP address on your network. By default, the xPico

module is assigned an IP address by your DHCP server. If no DHCP server is

available, the xPico will generate an AutoIP address (169.254.xxx.xxx).

If you are planning to use a static IP address, make note of it. The system

administrator generally provides the IP address, subnet mask, and gateway. The

IP address must be within a valid range, unique to your network, and in the same

subnet as your PC.

xPico Development Kit Quick Start Guide 5

IP Address: _______ _______ _______ _______

Subnet Mask: _______ _______ _______ _______

Gateway: _______ _______ _______ _______

Connecting an xPico Module — Network Method

A network connection, if the equipment is available, is the preferred method for

the initial configuration of the xPico.

Note: Before wiring and powering on the xPico Evaluation Board please make

sure that the correct xPico module for your needs is fitted. Removing and

inserting the xPico module is quite simple and requires removing the fitted

mounting clip and exchanging the module in the 40-pin socket.

1. Connect the PC to the Evaluation Board with a cross-over cable or a

hub/switch and two RJ45 cables. Make sure there is no router between the

PC and the Evaluation Board.

2. Select the appropriate power plug adaptor for your geographical location.

Insert it into the slot on the Universal Power Supply; then plug the power

supply into an outlet.

3. Connect the output plug of the power supply to the Evaluation Board.

4. Move the power switch on the Evaluation Board to ON.

This is the last step in 'connection.' The xPico is ready for configuration.

5. Continue with Install DeviceInstaller on page 6.

xPico Development Kit Quick Start Guide 6

Connecting an xPico Module — Serial Method

In the event that the equipment required for a network connection is not available

for the initial configuration of the xPico, the serial method can be used.

1. Connect one end of the supplied DB9F/F serial cable to the serial port on the

laptop or desktop.

2. Connect the other end of the supplied DB9F/F serial cable to Port 1 on the

xPico Evaluation Board.

3. Select the appropriate power plug adaptor for your geographical location.

Insert it into the slot on the Universal Power Supply; then plug the power

supply into an outlet.

4. Connect the output plug of the power supply to the xPico Evaluation Board.

The final serial connection setup should look like this:

5. Move the power switch on the Evaluation Board to ON.

This is the last step in 'connection.' The xPico is ready for configuration.

6. Continue with the Install DeviceInstaller section below.

Install DeviceInstaller

Use DeviceInstaller to configure the IP address and other network parameters.

Note: You will need a Windows PC running Lantronix DeviceInstaller 4.3.0.5 or

higher.

1. Download the latest version of DeviceInstaller from

www.lantronix.com/downloads.

2. Run the executable to start the installation process.

3. Respond to the installation wizard prompts. (If prompted to select an

installation type, select Typical.)

xPico Development Kit Quick Start Guide 7

Note: For more information about DeviceInstaller, see the DeviceInstaller Online

Help.

Assign an IP Address

The unit IP address is set for DHCP by default at the factory. The hardware

address is on the product label. Assign a static IP address if you do not want the

network to assign an IP address to the xPico or do not have a DHCP server on

the network.

1. Click StartPrograms LantronixDeviceInstaller 4.4

DeviceInstaller. If your PC has more than one network adapter, a

message appears. Select an adapter and click OK.

2. Click the Search icon and select the unit from the list of Lantronix device

servers on the local network. (In case no DHCP server is available, it can

take 30 seconds before an AutoIP address is generated and the unit is

detectable).

3. Click the Assign IP icon .

4. Select Assign a specific IP address and click Next.

xPico Development Kit Quick Start Guide 8

5. Enter the IP address.

The Subnet mask appears automatically based on the IP address.

You may change it. On a local network, you can leave the Default gateway

blank (all zeros).

6. Click Next.

7. Click Assign and wait several seconds until a confirmation message

appears.

8. Click Finish.

9. Select the xPico from the main window list and click Tools



Ping. The

results appear in the Status area.

10. Click Clear Status to clear the window to ping the device again.

Note: If you do not receive “Reply” messages, ensure the IP address assigned is

valid for the particular network segment you are working with.

11. Click Close.

xPico Development Kit Quick Start Guide 9

Configure Your xPico Device

Using DeviceInstaller it is easy to configure the unit over the network.

xPico Module

From DeviceInstaller it is easy to start the Lantronix browser-based tool, “Web

Manager” to configure the xPico. For detailed information on Web Manager

configuration and on other methods, see the xPico User Guide.

1. In DeviceInstaller, select the unit and then the Web Configuration tab. Click

the Go icon. The Lantronix Web Manager login window appears.

2. For the xPico, there is no default user name or password.

Note: We recommend that you always use the enhanced password setting

and create a strong 16 character password through Telnet or serial

connections. See the xPico Embedded Device Server User Guide available

at www.Lantronix.com/downloads for instructions. Using no password is very

dangerous.

3. Use the menu on the left to navigate to sub-pages where you can configure

the xPico module.

4. Commit any changes as follows:

Every sub-page has an OK button that tells the xPico what changes to

use, but it does not immediately change the configuration on the device.

When you are finished making all changes to the settings on various

pages, then click Apply Settings, which makes the changes permanent

and reboots the xPico.

xPico-IAP Module

From DeviceInstaller it is easy to start a Telnet connection to configure the unit

over the network. For detailed information on configuration, see the Modbus

Protocol User Guide.

1. In DeviceInstaller, select the unit and then the Telnet Configuration tab.

2. Click the Connect icon. The following information displays:

Lantronix Inc. - Modbus Bridge

MAC address 0080A366000D

Software version V3.3.0.0 (130306) XPICO

Press Enter for Setup Mode

3. To enter Setup Mode, press Enter within 5 seconds. The configuration

settings display, followed by the change prompt:

Select Command or parameter set (1..7) to change:

4. Select an option on the menu by entering the number of the option and

pressing Enter.

xPico Development Kit Quick Start Guide 10

5. To enter a value for a parameter, type the value and press Enter, or to

confirm a current value, just press Enter.

6. When you are finished making all changes to the various settings, use the

(S)ave option to save the new configuration by entering S. The unit

automatically reboots.

Autres manuels pour xPico

Table des matières

Autres manuels Lantronix Microcontrôleur

Lantronix

Lantronix XPort 080-318 Manuel utilisateur

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuel utilisateur

Lantronix

Lantronix Open-Q 845 mSOM Manuel utilisateur

Lantronix

Lantronix Open-Q 2100 Manuel utilisateur

Lantronix

Lantronix Open-Q 660 mSOM Manuel utilisateur

Lantronix

Lantronix EDS1100 Manuel utilisateur

Lantronix

Lantronix HDK845 Manuel utilisateur

Lantronix

Lantronix xPico Manuel utilisateur

Lantronix

Lantronix MatchPort Manuel utilisateur

Lantronix

Lantronix xPico 200 Series Manuel utilisateur

Lantronix

Lantronix Open-Q 865 Manuel utilisateur

Lantronix

Lantronix xPico 110 Manuel utilisateur

Lantronix

Lantronix Open-Q 212A Manuel utilisateur

Lantronix

Lantronix Open-Q 410 Manuel utilisateur

Manuels Microcontrôleur populaires d'autres marques

AMS

AMS AS7261 Demo Kit Manuel utilisateur

Novatek

Novatek NT6861 Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266 SDK Guide de configuration

Nuvoton

Nuvoton ISD61S00 ChipCorder Mode d’emploi

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuel utilisateur

Texas Instruments

Texas Instruments Chipcon CC2420DK Manuel utilisateur

NEC

NEC 78GK0S/K 1+ Series Instructions d'installation et d'utilisation

Mikroe

Mikroe SEMITECH N-PLC Click Instructions d'installation et d'utilisation

Intel

Intel Agilex Manuel utilisateur

Cypress

Cypress CY4607 HX2VL Manuel utilisateur

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuel utilisateur

Texas Instruments

Texas Instruments TMS320F2837 D Series Manuel utilisateur

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuel utilisateur

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Manuel utilisateur

Espressif Systems

Espressif Systems ESP8266EX Mode d'emploi

Abov

Abov AC33M8128L Manuel utilisateur

Laird

Laird BL654PA Manuel utilisateur

Silicon Laboratories

Silicon Laboratories C8051F800 Manuel utilisateur