Laguna Tools Timbermaster Manuel utilisateur

Laguna tools

Timbermaster manual

B01-00-0025

Dear Woodworker:

Thank you for your purchase and welcome to the Laguna Tools group of

discriminating woodworkers. I understand that you have a choice of where to

purchase your machines and appreciate the confidence you have in our

products.

Every machine sold by Laguna Tools has been carefully designed and well

thought through from a woodworkers perspective. I cut on our bandsaws,

lathes, table saws and combination machines. Through my hands-on

experience, I work hard to make our machines better. I strive to give you

machines that inspire you to create works of art. Machines that are a joy to

run and work on. Machines that encourage your performance.

Today, we offer high-performance machines with innovative solutions that

meet the needs of woodworkers and their ever-evolving craft.

I started Laguna Tools as a woodworker, I still am.

Thank you again for becoming a Laguna Tools customer.

Torben Helshoj

President and Founder - Laguna Tools

Thriving on innovation

Table of contents

Page number

Safety Rules

Warranty

Noise emission

Specification sheet

Receiveing your Timbermaster

Introduction to your Timbermaster

What you will receive with the Timbermaster

Parts of the Timbermaster

Where to locate your Timbermaster

Assembly and set up

Using the Timbermaster

Maintenance and troubleshooting

Safety Rules

As with all machinery there are certain hazards involved with the operation

and use. Using it with caution will considerably lessen the possibility of

personal injury. However, if normal safety precautions are overlooked or

ignored, personal injury to the operator may result. If you have any questions

relative to the installation and operation, do not use the equipment until you

have contacted your supplying distributor.

Read carefully before operating the machine.

1. Keep the working area clean and be sure adequate lighting is available.

2. Do not wear loose clothing, gloves, bracelets, necklaces or ornaments.

Wear face, eye, respiratory and body protection devices as indicated for

the operation or environment.

3. Be sure that the power is disconnected from the machine before tools

are serviced or an attachment is to be fitted or removed.

4. Never leave the machine with the power on.

5. Do not use dull, gummy or cracked cutting tools.

6. Be sure that the keys and adjusting wrenches have been removed and

all the nuts and bolts are secured.

Limited Warranty

New woodworking machines sold by Laguna Tools carry a one-year warranty from

the date of shipping. Laguna Tools guarantees all new machines sold to be free of

manufacturers’ defective workmanship, parts, and materials.

We will repair or replace, without charge, any parts determined by Laguna Tools,

Inc. to be a manufacturer's defect. We require the defective item/part to be returned

to Laguna Tools. In the event the item/part is determined to be

damaged due to lack of maintenance, cleaning or misuse/abuse, the customer

will be responsible for the cost to replace the item/part, plus all related shipping

charges.

This limited warranty does not apply to natural disasters, acts of

terrorism, normal wear and tear, product failure due to lack of maintenance or

cleaning, damage caused by accident, neglect, lack of or inadequate dust

collection, misuse/abuse or damage caused when repair or alterations have

been made or attempted by others.

Laguna Tools, Inc. is not responsible for additional tools or modifications sold or

performed (other than from/by Laguna Tools, Inc.) on any Laguna Tools, Inc.

woodworking machine. Warranty may be voided upon the addition of such noted

tools and/or modifications, determined on a case-by-case basis.

Normal user alignment, adjustment, tuning and machine settings are not

covered by this warranty. It is the responsibility of the user to understand

basic woodworking machinery settings and procedures and to properly maintain the

equipment in accordance with the standards provided by the manufacturer.

Parts, under warranty, are shipped at Laguna Tools, Inc's cost either by

common carrier, FedEx Ground service or similar method.

Technical support to install replacement parts is primarily provided by phone, fax, or

e-mail. The labour required to install replacement parts is the responsibility of the

user.

Laguna Tools is not responsible for damage or loss caused by a freight company or

other circumstances not in our control.

Only new machines sold to the original owner are covered by this warranty.

For warranty repair information, call 1-800-332-4094.

** Warning –no portion of these materials may be reproduced without written

approval from Laguna Tools, Inc.

All documentation subject to change without notice

Table stroke

5 foot

Table

19 in X 59 in [483mm X 1500mm]

Table height

adjustable

34 in min height to 45 in max height

Log-Lock system

Standard with micro-adjust

Footprint

10 foot long X 14 inches wide [3048mm X 355mm]

Weight / packaging

dimensions

Cabinets 171kg gross[1205mm X 460mm X1620mm]

Cabinets 376 lb gross [47.5 In X 18 in X 63.8in]

Support base 27 kg gross [1280 mm X 570mm X 125mm]

Support base 59lb gross [50in X 22.4in X 4.9 in]

Guide rail 56kg gross [3020mm X 200mm X 90mm]

Guide rail 123 lb gross [119in X 7.8 in X3.5 in]

Sliding table 40 kg gross [1525mm X 515mm X 75mm ]

Sliding table 88 lb gross [60In X 20 1/4in X 10 3/4in]

Noise emission

Notes concerning noise emission

Given that there exists a relationship between noise level and exposure times, it is

not precise enough to determine the need for supplementary precautions. The

factors affecting the true level of exposure to operators are clearly the amount of

time exposed, the characteristics of working environment other sources of dust and

noise etc. For example, adjacent machines in other words the level of ambient

noise. It is possible that exposure level limits will vary from country to country.

Specification sheet

Receiving your machine

Note: It is probable that your machine will be delivered by a third party. Before you

unpack your new machine you will need to first inspect the packing, invoice and

shipping documents supplied by the driver.

Insure that there is no visible damage to the packing or the machine. You need to do

this prior to the driver leaving. All damage must be noted on the delivery documents

and signed by you and the delivery driver. You must then contact the seller [Laguna

Tools] within 24.

Introduction to the Timbermaster

This Timbermaster is designed to give you years of safe service. Read this owner’s

manual in its entirety before assembly or use.

The Timbermaster consists of two cabinets that are joined with an “I” beam. The “I”

beam has a ground steel bar that supports the two linear bearings of the sliding

table.

The sliding table has steel support bars to raise the log off the table surface and

accommodate most log surface irregularities. The table has two log clamps that

move the log towards the blade of the bandsaw.

The cabinets sit in support bases that are vertically adjustable to suite the varying

height of bandsaws

Parts of the Timbermaster.

The Timbermaster does not have many parts. The major parts are discussed in this

manual. If you are not familiar with the Timbermaster, take the time to read this

section and become familiar with the machine.

1 2 3 4 5 6

1. Cabinet.

There are two cabinets that have support wheels for the sliding table. The cabinets

are very robust and provide a secure ridged base for the sliding table.

2. Support frame.

Each cabinet is attached to a support frame. The support frames have three support

feet that are vertically adjustable to suite the table height of your band saw.

3. Support feet.

The support feet have locking pins that allow the feet to be adjusted to the required

height. The fine height adjustment is achieved by rotating the rubber feet and

locking in position with the lock nuts.

The support feet have ratchet handles to clamp them once in the correct vertical

position and remove any rocking.

4. Sliding table.

The sliding table is constructed from heavy gauge steel plate and supports the log

clamps, support bars and the linear bearings. The support bars and log clamps can

be fitted in a number of positions to suite the log being cut.

5. Log clamps.

There are two log clamps that can be fitted in a number of positions to suite the log

being cut. They are attached to the sliding table with countersunk screws. They

have a quick action mechanism that allows a quick and convenient way to adjust the

position of the log attachment plates. The adjusters are vertically adjustable to suite

the diameter of the log being cut.

6. Rail.

The rail is manufactured from a heavy duty “I” beam. The rail connects the two

cabinets and supports the sliding table linear bearings.

7. Support bars.

Six support bars are provided to raise the log off the sliding table. This reduces the

possibility of the log rocking. The bars can be positioned in a number of positions to

suite the log being cut.

What you will receive with the Timbermaster.

Cabinet and support rail supplied inside of the cabinet

Cabinets

Rail & sliding table

Support base

Log clamps

Door lock in open position

Door keys

Parts shipped inside lower cabinet

Rail & fixings

Rail fixing screws etc

Sliding table and parts

Support bars

Table des matières

Autres manuels Laguna Tools Scie

Laguna Tools

Laguna Tools DAKE SE-1018 Manuel d'utilisation et d'entretien

Laguna Tools

Laguna Tools MTST5S-0135 Manuel utilisateur

Laguna Tools

Laguna Tools Dake Technics 350 CE Manuel utilisateur

Laguna Tools

Laguna Tools 18CX Manuel utilisateur

Laguna Tools

Laguna Tools MCO8000-0250 Manuel utilisateur

Laguna Tools

Laguna Tools DAKE SE-810 Manuel d'utilisation et d'entretien

Laguna Tools

Laguna Tools LT14 SEL Manuel utilisateur

Laguna Tools

Laguna Tools DAKE Euromatic 370S Manuel d'utilisation et d'entretien

Laguna Tools

Laguna Tools DAKE SUPER CUT 315 Manuel utilisateur

Laguna Tools

Laguna Tools HW110LS-30 Manuel utilisateur

Laguna Tools

Laguna Tools MPSP12-5-0135 Manuel utilisateur

Laguna Tools

Laguna Tools Fusion 3 Manuel utilisateur

Laguna Tools

Laguna Tools 14BX Series Manuel utilisateur

Laguna Tools

Laguna Tools Dake VDL-18 Guide de l'utilisateur

Laguna Tools

Laguna Tools Dake SE-5X6 RCT Manuel d'utilisation et d'entretien

Laguna Tools

Laguna Tools Fusion F1 Manuel utilisateur

Laguna Tools

Laguna Tools Fusion 2 Manuel utilisateur

Laguna Tools

Laguna Tools DAKE Technics 350 SA Manuel d'utilisation et d'entretien

Laguna Tools

Laguna Tools Fusion 1 Manuel utilisateur

Laguna Tools

Laguna Tools MBAND18BX2203 Manuel utilisateur

Laguna Tools

Laguna Tools Platinum Series Manuel utilisateur

Laguna Tools

Laguna Tools 18BX Manuel utilisateur

Laguna Tools

Laguna Tools Dake VDL-18 Manuel d'utilisation et d'entretien

Laguna Tools

Laguna Tools 16HD Classic Manuel utilisateur

Manuels Scie populaires d'autres marques

RIDGID

RIDGID BS1400 Manuel utilisateur

ATIKA

ATIKA BWS 400-2 Manuel utilisateur

RGC

RGC FS20 Manuel utilisateur

Makita

Makita M2300 Manuel utilisateur

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manuel utilisateur

IMET Spa

IMET Spa SIRIO 370 AF-E Manuel utilisateur

Optimum

Optimum OPTisaw CS 275 Manuel utilisateur

Makita

Makita BPB180 Manuel utilisateur

Stihl

Stihl MS 462 C-M Manuel utilisateur

AEG

AEG TS 250 K Manuel utilisateur

Meec tools

Meec tools 004665 Manuel utilisateur

Makita

Makita LS1018L Manuel utilisateur

Ryobi

Ryobi RCS1400 Manuel utilisateur

DeWalt

DeWalt DCS391 Manuel utilisateur

Sealey

Sealey SA72 Manuel utilisateur

skilsaw

skilsaw SPT88 Instructions de montage

Urrea

Urrea SI810 Dimensions et guide d'installation

EINHELL

EINHELL BKG 210/1 Manuel utilisateur