La Crosse Technology CYCLONE PRO SENSOR Manuel utilisateur

CYCLONE PRO SENSOR

Wind

Direction

Wind

Speed

Solar Panel

Assisted Power

Rain Readings

Now with dual tipper for

improved accuracy

Easy-to-Install

Mounting Bracket LTV-WSDR1

Initial Setup

Installing the Wind Cups (if needed)

1. Remove the Cyclone Pro Sensor, Wind

Cups, and Mini Screwdriver from the

package. Take note of the ﬂat edges

located on the head of the Sensor and

underside of the Wind Cups.

3. Carefully tighten the screw on the side

of the cups using the Mini Screwdriver. The

screw should tighten into the ﬂat edge of

the post.

2. Align the ﬂat edges and place the Wind

Cups on top of the Cyclone Pro Sensor.

4. When the screw is tight, gently pull up on

the cups to ensure they are secure.

If they pull o, start again with step two.

Powerup

Insert 3-AA batteries into the

bottom of the Cyclone Pro

Sensor according to polarity.

Install 3-AA Batteries

Adding Your Sensor to the La Crosse View App

1. Open your La Crosse View app. On the Main Menu,

scroll to ADD/EDIT and select DEVICES.

2. On the Devices page, select the ADD DEVICE or PLUS (+)

button.

3. Scan the Barcode on your Sensor or type in the Device ID

manually.

4. Conﬁrm the sensor image and Device ID and add a Device

Name and Location Name. Select DONE.

123456-ABC

Bottom of Cyclone Sensor ⊲

 Use the built-in Bubble Level to ensure the Cyclone Pro

Sensor (especially the rain gauge) is mounted level.

 Ensure the Solar Panel is facing to the South. This helps

optimize battery life and transmit correct wind direction data.

 Ideally, the Cyclone Pro Sensor should be mounted on the

tallest object in your area. Avoid positioning the sensor

parallel or below eaves, roof lines, trees, or other objects that

may obstruct wind and rain readings.

 Make sure all the screws on the Mounting Bracket, Wind

Cups, Wind Vane, and Battery Compartment are securely

fastened.

 The Cyclone Pro Sensor should be mounted with the Wind

Cups on the top.

Sensor Placement & Mounting

For Accurate Cyclone Sensor Measurements

Bubble Level

Fence posts, poles, decks, and mailboxes are common mounting options due to their convenience.

Many users prefer these types of locations as the data they provides is accurate from their ground

level. However, because the wind in these spots is often aected by obstructions, the readings may

dier when compared to local reporting stations.

Basic Installation

Mount the Mast to a ﬂat surface with the four

provided screws.

1. 2. Place the Cyclone Pro Sensor on top of the Mast.

Ensure the Solar Panel is facing south.

Sensor Placement & Mounting

Check the integrated Bubble Level or use your own

across the Rain Funnel to ensure the sensor is level.

Secure the Cyclone Sensor to the Mast by tightening

the screws on the side. After screws are tightened,

double check the sensor has remained level

through the installation process.

3. 4.

Flexible Installation

Install the Hand Screw to the bracket, then Secure

the Cyclone Sensor to the Mast by tightening the

screws on the side.

This conﬁguration allows you to attach the sensor

to angled locations and easily make adjustments

to ensure the Mast and Sensor are level.

Hand Screw

2. Clear any leaves, insects, or other debris

to allow the Rain Tipper to rock freely.

Check and clear the Drainage Holes

located on the underside of the sensor. 6

Cyclone Pro Sensor Mounting

Cleaning the Rain Sensor

1. Remove the Rain Funnel by ﬁrmly twisting

the funnel counter-clockwise and lifting up.

Some advanced installation options include tripods, wall mounts, chimney mounts, and many others.

Any of these can be combined with U-bolts for attachment onto a tall cylindrical conduit using our

Adjustable Base. These options will require additional equipment and possibly professional help for

best results.

Advanced Installation

Freestanding Pole Setup

1'' Maximum Outside

Pole Diameter

Tripod Setup Example

1'' Maximum Outside

Pole Diameter

11.60”

29.44cm

13.80”

35.04cm

9.12”

23.16cm

12.47”

31.69cm

5.18”

13.15cm

3. After cleaning, re-install the Rain Funnel by

placing it back into the sensor and twisting

clockwise until secure.

4. You should feel the funnel lock into place

when one of the arrows lines up with the

center of the Lock/Unlock Line.

Tip: Remove the Cyclone Pro Sensor’s batteries before cleaning to avoid accidental rain

readings.

Speciﬁcations

CYCLONE PRO SENSOR (LTV-WSDR1)

• Wind Speed Range: 0 to 111 mph

(0 to 178 kph)

• Rainfall Range: 0 to 393.6 Inches

(0 to 9999 mm)

• Transmission Range: 400 feet 915MHz

(121 meters) open air

• Power Requirements: 3 “AA” Batteries

(not included)

• Update Interval: Every 31 Seconds

California Residents

CA WARNING: This product can expose

you to chemicals including acrylonitrile,

butadiene, and styrene, which are known

to the State of California to cause cancer

and birth defects or other reproductive

harm. For more information, go to:

www.P65Warnings.ca.gov

Warranty

Use the links below to ﬁnd additional resources or reach out toour sta directly.

Representatives are available Monday-Friday, 8am-6pm CST

Online: bit.ly/contact_techsupport

Phone: 1.844.200.8752

La Crosse Technology, Ltd. provides a 1-year limited time

warranty (from date of purchase) on this product, relating to

manufacturing defects in materials and workmanship.

For full warranty details, visit:

www.lacrossetechnology.com/pages/warranty

La Crosse Technology, Ltd.

2830 S. 26th Street, La Crosse, Wisconsin 54601

Follow La Crosse Technology on Facebook,

Instagram, YouTube, and Twitter.

Stay in Touch

Ask questions, watch setup videos, and provide

feedback on our social media outlets.

We’re here to help.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

FCC Radiation Exposure Statement

This device complies with FCC radiation exposure limits set

forth for an uncontrolled environment and it also complies with

Part 15 of the FCC RF Rules. This equipment must be installed

and operated in accordance with provided instructions and the

antenna(s) used for this transmitter must be installed to provide

a separation distance of at least 20 cm from all persons and

must not be co-located or operating in conjunction with any

other antenna or transmitter. End-users and installers must be

provided with antenna installation instructions and consider

removing the no-collocation statement.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received,

including interference that may cause undesired operation.

Caution: Any changes or modiﬁcations not expressly approved

by the party responsible for compliance could void the user's

authority to operate the equipment.

• Reorient or relocate the receiving antenna.

• Connect the equipment into an outlet on a circuit dierent

from that to which the receiver is connected.

• Increase the separation between the equipment and receiver.

• Consult the dealer or an experienced radio/TV technician

for help.

Battery Replacement Instructions

When batteries of dierent brand or type are used together, or new and old batteries are used together, some batteries may

be over-discharged due to a dierence of voltage or capacity. This can result in venting, leakage, and rupture and may cause

personal injury.

•Always purchase the correct size and grade of battery most suitable for the intended use.

•Always replace the whole set of batteries at one time, taking care not to mix old and new ones, or batteries of dierent

types.

•Clean the battery contacts and also those of the device prior to battery installation.

•Ensure the batteries are installed correctly with regard to polarity (+ and -).

•Remove batteries from product during periods of non-use. Battery leakage can cause corrosion and damage to this product.

•Remove used batteries promptly.

•For recycling and disposal of batteries, and to protect the environment, please check the internet or your local phone

directory for local recycling centers and/or follow local government regulations.

Battery Replacement

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels La Crosse Technology Accessoires

La Crosse Technology

La Crosse Technology D000.104 Manuel utilisateur

La Crosse Technology

La Crosse Technology TX146 Manuel utilisateur

La Crosse Technology

La Crosse Technology TX60U-IT Manuel utilisateur

La Crosse Technology

La Crosse Technology TX24U Manuel utilisateur

La Crosse Technology

La Crosse Technology LTV-POOLv2 Manuel utilisateur

La Crosse Technology

La Crosse Technology TX12U Manuel utilisateur

La Crosse Technology

La Crosse Technology TX15U Manuel utilisateur

La Crosse Technology

La Crosse Technology CA82738-1 Manuel utilisateur

La Crosse Technology

La Crosse Technology TX-23U Manuel utilisateur

La Crosse Technology

La Crosse Technology LTV-THP1-T1 Manuel utilisateur

La Crosse Technology

La Crosse Technology 925-1418 Manuel utilisateur

La Crosse Technology

La Crosse Technology CA79097 Manuel utilisateur

La Crosse Technology

La Crosse Technology TX141-B4 Manuel utilisateur

La Crosse Technology

La Crosse Technology TX23U Manuel utilisateur

La Crosse Technology

La Crosse Technology TX191 Manuel utilisateur

La Crosse Technology

La Crosse Technology TX141TH-BCHv3 Manuel utilisateur

La Crosse Technology

La Crosse Technology La Crosse Alerts TX60U-IT Manuel utilisateur

La Crosse Technology

La Crosse Technology LTV-R1 Manuel utilisateur

La Crosse Technology

La Crosse Technology TX10U Manuel utilisateur

La Crosse Technology

La Crosse Technology TX145R Manuel utilisateur

La Crosse Technology

La Crosse Technology Outdoor Temperature/Humidity Sensor TX7U Manuel utilisateur

La Crosse Technology

La Crosse Technology TX141TH-BV4 Manuel utilisateur

La Crosse Technology

La Crosse Technology LTV-WR1 Manuel utilisateur

La Crosse Technology

La Crosse Technology TX5 Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur