Kreg KFPCHB Manuel utilisateur

STEP 1:

Set Up Your Pocket-Hole Jig

Scan the QR to watch a video for this step

AUse Material Thickness Gauge / Hex Wrench to measure material thickness (¾").

BSet jig material thickness to ¾".

Note: You can use most Kreg Pocket-Hole Jigs for this project. Be sure to set up and

use your jig according to the manufacturer’s instructions, and follow this guide for

proper hole placement.

CSet drill bit stop collar to ¾" (loosen and tighten stop collar with Hex Wrench).

A B C

WOODWORKING KIT CORNHOLE BOARDS

Included in Bundle

7Pocket-Hole Jig 520PRO

8Versa-GripTM Clamp - 24"

92" Classic Face Clamp

10 Material Thickness Gauge

11 #2 Driver Bit

12 Easy-Set Drill Bit and Stop Collar

13 2 1/2" Pocket-Hole Screws

14 1 1/4" Pocket-Hole Screws

Base Kit

1 Side Rail

2Cross Brace

3Top

4Leg Brace

5Leg

6Cornhole Board Hardware

BEFORE YOU

GET STARTED

We want to make sure

have you the guidance

and resources you

need to be successful

with this project.

Simply scan the QR

code below for tips and

tricks on setting up

your jig, drilling pocket

holes, and more.

WARNING:

Drilling, sawing, sanding or machining wood products can expose you to wood dust, a substance known to the State of

California to cause cancer. Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection. For more information

go to www.P65Warnings.ca.gov/wood.

WARNING:

Improper assembly or excessive weight applied to the nished product could result in injury. Follow all instructions provided

for assembly. Kreg is not responsible for injuries as a result of improper assembly or use.

WARNING:

Always wear personal protective equipment certied as such, including safety glasses, hearing protection, and respiratory

protection. When using a power tool, always follow the manufacturer’s personal protection equipment requirements. Gloves are

recommended for handling unnished wood products.

STEP 2:

Drill Pocket-Holes in Cross Braces (x8)

Scan the QR to watch a video for this step

STEP 3:

Drill Pocket-Holes in Leg Braces (x2)

Scan the QR to watch a video for this step

E F

AClamp Cross Brace so it is centered in the jig.

BDrill two pocket holes using the outside drill guides.

CFlip Cross Brace 180° in the jig and repeat steps A-B on the

other end of the Cross Brace.

DAlign outside edge of jig to inside edge of existing pocket

holes, ensuring end stop and drill pocket hole. Repeat on the

other end of the Cross Brace.

EAlign jig so one drill guide hole is centered on Cross Brace

and drill one pocket hole.

FRepeat steps A-E for remaining Cross Braces.

AClamp Leg Brace in jig so outside drill guides are

approximately 1" from outside edges of board.

BDrill two pocket holes using the outside drill guides.

CFlip Leg Brace 180° in the jig.

DRepeat A-B on the other end of the Leg Brace.

ERepeat A-D for second Leg Brace.

STEP 4:

Assemble Frame

Scan the QR to watch a video for this step

B C D

E F

AOptional: Workpiece edges and pocket holes can be sanded

prior to assembly.

B AlignedgeofrstCrossBracewithguidelinesofboth

Side Rails. Important: Ensure all pocket holes are facing the

correct direction, as indicated in photo B.

C ClampsiderailstorstCrossBrace,checkingtomakesure

alignment with guide line is consistent.

Important: Position pieces so that pocket-holes point in

toward the center.

DUse #2 driver bit to drive 1 ¼" pocket-hole screws into

Cross Brace.

Tip: Adjust drill clutch for driving screws. Do NOT use an

impact driver, as this may lead to over-driven screws or

stripped screw heads.

EPlace second Cross Brace so it aligns with next guide line

indicated on Side Rails.

FUse #2 driver bit to drive 1 ¼" pocket-hole screws into the

Cross Brace.

GPlace remaining Cross Braces so they align with remaining

guide lines and attach with #2 driver bit and 1 ¼" pocket-

hole screws.

HEnsure assembled frame matches photo H.

IRepeat A - H for second Frame Assembly.

APlace Frame Assembly on Top and position so that corners

of Frame Assembly align with guide lines located at each

corner of Top.

BClamp the Top and Frame Assembly to the work surface.

CUse #2 driver bit to drive 1 ¼" pocket-hole screws into Cross

Braces.

Tip: Adjust drill clutch for driving screws. Do NOT use an

impact driver, as this may lead to over-driven screws or

stripped screw heads.

DAttach the Cross Braces by driving 1 ¼" pocket-hole screws,

starting with the pocket holes in one corner then moving

to the opposite corner. After all four corners are attached,

attach remaining Cross Braces with pocket-hole screws.

ERepeat A - D for second Top and Frame Assembly.

STEP 5:

Attach Top to Frame (x2)

Scan the QR to watch a video for this step

A B C D

STEP 6:

Assemble and Attach Legs (x4)

Scan the QR to watch a video for this step

ABCD

AAlign edge of Leg Brace with guide line on Leg as shown in

photo A.

BUse #2 driver bit to drive 1 ¼" pocket-hole screws into Leg

Brace.

Tip: Adjust drill clutch for driving screws. Do NOT use an

impact driver, as this may lead to over-driven screws or

stripped screw heads.

CRepate A - B for second Leg.

DArrange included Bolt, Washers, and Nut as shown

in photo D.

EInsert the rounded end of Leg Brace into Frame and line

up the hole in the Frame with the hole in the Leg. Slide bolt

through bolt hole and secure using the washers and nut.

Note: Place one washer between the bolt head and Side Rail,

Side Rail and Leg, and the nut and Leg. Tighten nut using a

pair of combination or adjustable wrenches.

Tip: Avoid under- or over-tightening the nut, so the Leg

Assembly moves freely but stays in place when folded up.

FRepeat steps for second assembly.

STEP 7:

Customize it!

Scan the QR to watch a video for this step

A Onceyou’renishedaddingyourowndecorativetouches,

take a photo and post it with the #builtwithkreg hashtag to

show your work and see what others are building with Kreg.

NOTE: For best results, seal top and edges of cornhole boards.

The material used is a composite that can be vulnerable to

water damage if not properly sealed. For tips on how to apply

sealer to edges, please visit: https://learn.kregtool.com/learn/

make-painted-plywood-edges-look-great/.

Manuels Outils populaires d'autres marques

Martor

Martor SECUNORM 175 Manuel utilisateur

ERKCO

ERKCO 1000 Manuel utilisateur

jbc

jbc N4473 Manuel utilisateur

FEINMETALL

FEINMETALL FZWZ-SET-001 Manuel utilisateur

Worx Professional

Worx Professional Sonicrafter WU676 Manuel utilisateur

Gage Bilt

Gage Bilt GB713SH Manuel utilisateur

Hilti

Hilti DX 9-ENP Manuel utilisateur

norbar

norbar NORTRONIC 34399 Manuel utilisateur

BGS technic

BGS technic 8578 Manuel utilisateur

Makita

Makita DHR241 Manuel utilisateur

Motor Guard

Motor Guard JMB-1250 Manuel utilisateur

Power Adhesives

Power Adhesives 805-12 Manuel utilisateur

Clemco

Clemco 24189 Manuel utilisateur

VVG

VVG VNG 903 Series Manuel utilisateur

Hilti

Hilti FX 3-A Manuel utilisateur

Grizzly

Grizzly H6472 Manuel utilisateur

axing

axing BWZ 5-02 Manuel utilisateur

Dh-Robotics

Dh-Robotics RGI-100 Comment utiliser