Kramer SL-10 Manuel utilisateur

KRAMER ELECTRONICS LTD.

USER MANUAL

MODEL:

-10

Master

Room Controller

P/N: 2900-000581 Rev 6

SL-10 – Contents i

Contents

1Introduction 1

2Getting Started 2

2.1 Achieving the Best Performance 2

2.2 Safety Instructions 3

2.3 Recycling Kramer Products 3

3Overview 4

3.1 Defining the SL-10 Master Room Controller 5

4Connecting the SL-10 7

4.1 Using the RC-4 IR Transmitter 8

4.2 Connecting the RS-232 Interface 8

4.3 Connecting the RS-485 Interface 9

4.4 Connecting the Ethernet Port 9

4.5 Connecting the K-NET Port 10

5Operating the SL-10 11

6Technical Specifications 12

Figures

Figure 1: SL-10 Master Room Controller 5

Figure 2: Connecting the SL-10 Master Room Controller 8

Figure 3: RS-232 Connection 9

Figure 4: RS-485 Connection 9

Figure 5: K-NET PINOUT Connection 10

SL-10 - Introduction

1 Introduction

Welcome to Kramer Electronics! Since 1981, Kramer Electronics has been

providing a world of unique, creative, and affordable solutions to the vast range of

problems that confront video, audio, presentation, and broadcasting professionals

on a daily basis. In recent years, we have redesigned and upgraded most of our

line, making the best even better!

Our 1,000-plus different models now appear in 11 groups that are clearly defined

by function: GROUP 1: Distribution Amplifiers; GROUP 2: Switchers and Routers;

GROUP 3: Control Systems; GROUP 4: Format/Standards Converters; GROUP 5:

Range Extenders and Repeaters; GROUP 6: Specialty AV Products; GROUP 7:

Scan Converters and Scalers; GROUP 8: Cables and Connectors; GROUP 9:

Room Connectivity; GROUP 10: Accessories and Rack Adapters and GROUP 11:

Sierra Products; GROUP 12: Digital Signage; GROUP 13: Audio; and GROUP 14:

Collaboration.

Congratulations on purchasing your Kramer SL-10 Master Room Controller, which

is ideal for the following typical applications:

•Master room controller for room control systems

•Multimedia room control, such as classrooms, meeting rooms and

auditoriums

2 SL-10 - Getting Started

2 Getting Started

We recommend that you:

•Unpack the equipment carefully and save the original box and packaging

materials for possible future shipment

•Review the contents of this user manual

Go to www.kramerav.com/support/product_downloads.asp

to check for up-to-date user manuals, application programs, and to check if

firmware upgrades are available (where appropriate).

2.1 Achieving the Best Performance

To achieve the best performance:

•Use only good quality connection cables (we recommend Kramer high-

performance, high-resolution cables) to avoid interference, deterioration in

signal quality due to poor matching, and elevated noise levels (often

associated with low quality cables)

•Do not secure the cables in tight bundles or roll the slack into tight coils

•Avoid interference from neighboring electrical appliances that may adversely

influence signal quality

•Position your Kramer SL-10 away from moisture, excessive sunlight and dust

This equipment is to be used only inside a building. It may only be

connected to other equipment that is installed inside a building.

SL-10 - Getting Started

2.2 Safety Instructions

Caution:

There are no operator serviceable parts inside the unit

Warning: Use only the Kramer Electronics input power wall

adapter that is provided with the unit

Warning: Disconnect the power and unplug the unit from the wall

before installing

2.3 Recycling Kramer Products

The Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC

aims to reduce the amount of WEEE sent for disposal to landfill or incineration by

requiring it to be collected and recycled. To comply with the WEEE Directive,

Kramer Electronics has made arrangements with the European Advanced

Recycling Network (EARN) and will cover any costs of treatment, recycling and

recovery of waste Kramer Electronics branded equipment on arrival at the EARN

facility. For details of Kramer’s recycling arrangements in your particular country

go to our recycling pages at www.kramerav.com/support/recycling/.

4 SL-10 - Overview

3 Overview

The SL-10 is a highly versatile controller that acts as an all-in-one control

processor for control of A/V equipment—especially projectors and associated

equipment—in any room (such as classrooms, boardrooms, or auditoriums).

It streamlines operations and simplifies control by integrating audio, video, and

computer-video sources into a centralized system.

The SL-10 features:

•An Ethernet port for controlling several AV products over ETH

•2 general purpose I/O ports that can be configured as analog inputs, digital

inputs, or digital outputs for interfacing with a variety of devices such as

sensors, switches, LEDs, and relays

•2 bidirectional RS-232 ports that control AV equipment such as projectors,

LCD and PDP displays, power amplifiers, switchers and scalers

•5 relay contact closure ports that control other room items related to the AV

system such as raising and lowering drapes, the screen or the projector

•IR control on one built-in receiver and the other on a 3.5mm mini jack and

three outputs (on terminal blocks)

•IR Learning that learns commands from any IR remote

•1 RS-485 serial port

•Compatibility with Kramer Site-CTRL software for network remote control

and management over the Ethernet port

•A K-NET™ control channel that connects compatible user interfaces and

supplies power and control data over a single cable

•A USB port for uploading a configuration file

•Status LEDs for all functions

•Flexible control via Ethernet, K-NET™, RS-485, an IR sensor and external

IR commands

SL-10 - Overview

3.1 Defining the SL-10 Master Room Controller

This section defines the SL-10.

Figure 1: SL-10 Master Room Controller

Feature

Function

ETHERNET RJ-45 Connector

Connects to the PC or other serial controller through

computer networking LAN to control several AV

products over Ethernet

DEFAULT Recessed Pushbutton

Press to reset to factory default definitions:

IP number −192.168.1.39, Mask – 255.255.0.0

Gateway – 0.0.0.0

First disconnect the power supply and then connect it

again while pressing the DEFAULT button. The unit

powers up and loads its memory with the factory default

definitions and erases all stored presets

IR Output Terminal Blocks

Connect to IR emitter cables (from 1 to 3)

GPI/O Terminal Blocks

Connect to various analog and digital sensors (from 1

to 2)

RELAYS Terminal Blocks

Connect to low-voltage relay-driven devices (from 1 to

RS-232 Terminal Blocks

Connect to the RS-232 devices (from 1 to 2)

7 RS-485 Terminal Block Pins B (-) and A (+) are for RS-485; Pin G may be

connected to the shield (if required)

6 SL-10 - Overview

Feature

Function

K-NET

Connector

PIN GND is for the Ground connection; PIN B (-) and

PIN A (+) are for RS-485, and PIN +12V is for

powering other units

K-NET is a proprietary Kramer protocol for

interconnecting Kramer units

The ground connection is sometimes connected to the

shield of the RS-485 cable (in most applications, it is not

connected)

Note that the SL-10 cannot receive power via the K-NET

connector, but can power other units (but not another

SL-10)

RS-485 TERM Switch

Slides down for RS-485 termination, slides up for not

terminated

K-NET TERM Switch

Slides down for K-NET termination, slides up for not

terminated

PROG. Switch

For service use only

12V DC Socket

12V DC connector for powering the unit

13 IR

INPUTS Built-in receiver and

STATUS LED

Accepts IR remote commands

3.5mm Mini Jack

Connects to an external IR receiver

RELAY LEDs

Illuminate when a relay is active (1 to 5)

IR LEDs

Illuminate when an IR port is active

NET LED

Illuminates when The Ethernet link is active

K-NET LED

Illuminates while transmitting over K-NET

RS-485 LED

Illuminates while transmitting/receiving on an RS-485

port

RS-232 (Tx/Rx) LEDs

Illuminate while transmitting/receiving on an RS-232

port (1 to 2)

GPI/O LEDS

Illuminate while transmitting/receiving on a general

purpose I/O port (1 to 2)

22 PROGRAM USB Connector Connect to a computer for unit configuration and

firmware upgrading

SL-10 - Connecting the SL-10

4 Connecting the SL-10

Always switch off the power to each device before connecting it to your

SL-10. After connecting your SL-10, connect its power and then switch

on the power to each device.

To connect the SL-10 as illustrated in the example in Figure 2:

1. Connect the RELAY terminal block connectors as follows:

Connect RELAY 1 and 2 to the projector lift

Connect RELAY 3 and 4 to the screen

Connect RELAY 5 to the lighting system

2. Connect the IR outputs as follows:

Connect an IR emitter to IR OUTPUT 1 and attach the emitter to the

DVD player

3. Connect the GPI/O ports as follows:

Connect GPI/O 1 to motion detector 1

Connect GPI/O 2 to motion detector 2

4. Connect the RS-232 ports as follows:

Connect RS-232 port 1 to the DVD player

Connect RS-232 port 2 to the projector

5. Connect the IR input as follows:

Connect IR INPUT 1 to an IR sensor (or alternatively connect IR

INPUT 1 to an external IR receiver

P/N: C- A35M/IRR two extension cables are also available: a 15 meter cable and

a 20 meter cable.

6. Connect the RS-485 to several Kramer matrices, for example.

Not shown in Figure 2.

7. Connect the Ethernet port to a network.

Autres manuels pour SL-10

Table des matières

Autres manuels Kramer Contrôleurs

Kramer

Kramer SL-1 Manuel utilisateur

Kramer

Kramer RC-76R Manuel utilisateur

Kramer

Kramer RC-43SL Manuel utilisateur

Kramer

Kramer FC-26 Manuel utilisateur

Kramer

Kramer FC-18 Manuel utilisateur

Kramer

Kramer SL-12 Manuel utilisateur

Kramer

Kramer RC-74DL Manuel utilisateur

Kramer

Kramer RC-6 Manuel utilisateur

Kramer

Kramer FC-18 Manuel utilisateur

Kramer

Kramer KC-Virtual Brain5 Manuel utilisateur

Kramer

Kramer RC-7B Manuel utilisateur

Kramer

Kramer SL-12 Manuel utilisateur

Kramer

Kramer SL-240 Manuel utilisateur

Kramer

Kramer PL-50 Manuel utilisateur

Kramer

Kramer SL-240C Manuel utilisateur

Kramer

Kramer RC-2 Manuel utilisateur

Kramer

Kramer SL-10 Manuel utilisateur

Kramer

Kramer RC-7LC Manuel utilisateur

Kramer

Kramer RC-13TC Manuel utilisateur

Kramer

Kramer SL-12 Manuel utilisateur

Kramer

Kramer RC-63DLN Manuel utilisateur

Kramer

Kramer RC-52N Manuel utilisateur

Kramer

Kramer RC-62 Manuel utilisateur

Kramer

Kramer PT-12 Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur