KPS DMM4500PV Manuel utilisateur

User Manual / MANUAL DEL USUARIO /

Manuel d'utilisation /

Benutzerhandbuch / Manuale Utente

DMM4500PV

All New Designed Bluetooth DMM

Multímetro digital bluetooth con nuevo diseño

Tout nouveau design DMM Bluetooth

Ganz NEU gestaltetes Bluetooth DMM

DMM Bluetooth di Progettazione COMPLETMENTE NUOVA

LIMITED

WARRANTY

YEARS

DMM4500PV

!Safety Information

Understand and follow operating instructions carefully. Use the

meter only as .

WARNING

If the equipment is used in a manner not specified by the

manufacturer, the protection provided by the equipment may

be impaired.

Always use proper terminals, switch position, and range for

measurements.

To reduce the risk of fire or electric shock, do not use this product

around explosive gas or in damp locations.

Verify the Meter operation by measuring a known voltage.

If in doubt, have the Meter serviced.

Do not apply more than the rated voltage, as marked on

Meter, between terminals or between any terminal and earth

ground.

To avoid false readings that can lead to electric shock and injury,

replace the battery as soon as low battery indicator blinks.

Avoid working alone so assistance can be rendered.

Do not use the Tester if the Tester is not operating properly or if it

is wet.

Individual protective device must be used if hazardous live parts

in the installation where the measurement is to be carried out

could be accessible.

Disconnect the test leads from the test points before changing

the position of the function rotary switch.

Never connect a source of voltage when the function rotary

switch is not in voltage position.

When using test leads or probes, keep your fingers behind the

finger guards.

Use caution with voltages above 30 Vac rms, 42 Vac peak, or 60

Vdc. These voltages pose a shock hazard.

Remove test lead from Meter before opening the battery door

or Meter case.

DO NOT USE the test leads when the internal white insulation

layer is exposed.

DO NOT USE the test leads above maximum ratings of CAT.

environment, voltage and current, that are indicated on the

probe and the probe tip guard cap.

DO NOT USE the test leads without the probe tip guard cap in

CAT III and CAT IV environments.

Probe assemblies to be used for MAINS measurements shall

be RATED as appropriate for MEASUREMENT CATEGORY

III or IV according to IEC 61010-031 and shall have a voltage

RATING of at least the voltage of the circuit to be measured.

Only replace the blown fuse with the proper rating as specified

in this manual.

DMM4500PV

Symbols as marked on the Meter and Instruction

manual

Do not attempt a current measurement when the open voltage

is above the fuse protection rating. Suspected open voltage

can be checked with voltage function.

Never attempt a voltage measurement with the test lead inserted

into the A input terminal.

Disconnect circuit power and discharge all high-voltage

capacitors before testing resistance, continuity, diodes, or

capacitance.

Risk of electric shock

See instruction manual

DC measurement

AC measurement

Wireless transmission Both direct and

alternating current

Equipment protected by double or reinforced insulation

Low battery

Fuse

Earth

Application around and removal from

hazardous live conductors is permitted

Do not discard this product or throw away.

Attention! Magnets might affect the correct functioning

of cardiac pacemakers and implanted defibrillators.

As a user of such medical devices, keep a sufficient

distance to the magnet.

Conforms to EU directives

Unsafe Voltage

To alert you to the presence of a potentially hazardous voltage,

when the Tester detects a voltage ≧30 V or a voltage overload

(OL) in V, mV, PV. The symbol is displayed.

Maintenance

Do not attempt to repair this Meter. It contains no user

serviceable parts. Repair or servicing should only be performed

by qualified personnel.

DMM4500PV

Cleaning

Periodically wipe the case with a dry cloth and detergent.

Do not use abrasives or solvents.

Introduction

The Meter Description

Front Panel Illustration

1. Volt Seek Light

2. 6,000 count digital display

3. Push-buttons.

4. Rotary switch for turn the Power On / Off and select the function.

5. Input Terminal for Multi-function.

6. Common (Ground reference) Input Terminal.

7. Input Terminal for A.

A COM

Volt Seek

Volt Seek Light

LCD Display

Button

Rotary Switch

V,ȍ, ,°C Input (or “+” )

Common Input

A Input

DMM4500PV

Measuring Voltage

Making Basic Measurements

Preparation and Caution Before Measurement

Observe the rules of Warnings and Cautions.

! ! !

!CAUTION

When connecting the test leads to the DUT (Device Under Test)

connect the common test leads before connecting the live test

leads ; when removing the test leads, remove the live test leads

before removing the common test leads.

Dial the switch to select the measuring function.

DMM4500PV

Measuring Voltage

Dial the switch and press the Function button to select the

measuring function.

!CAUTION

This function is only available with the dedicated PV test probe.

Always select correct DC / AC mode to perform high voltage

measurement. This meter will flash symbol and the correct

mode symbol (AC / DC) if the input voltage is different and

dangerous.

DMM4500PV

Measuring Current

Dial the switch and press the Function button to select the

measuring function.

Dial the switch and press the Function button to select the

measuring function.

Disconnect

Measuring Capacitance / Diode

DMM4500PV

Measuring Continuity / Resistance

Dial the switch and press the Function button to select the

measuring function.

Dial the switch and press the Function button to select the

measuring function. (°C / °F)

Measuring Temperature °C / °F

Red Black

DMM4500PV

Volt Seek

Dial the switch to select the measuring function.

Press the Function button to change the function on the same

switch position.

Using the Function

Do not hold across this

line when sensing the

hazardous voltage.

Volt

Seek

!Warning

The Volt Seek LED indicates the electric field. If the Volt Seek

LED is not on, voltage could still be present.

Switch

Position

Function

DMM4500PV

Range Button

The MAX/MIN mode records the min and max input values.

When the input goes below the recorded min value or above the

recorded max value, the meter records the new value. Press

Hold button to pause the recording.

MIN/MAX

Press Range Button >2 Sec to Enter Auto Range Mode

Auto Range Mode

Manual Range Mode

Switch range

Press Button > 2 sec

to exit the MIXMAX mode

Table des matières

Langues :

Autres manuels KPS Instrument de mesure

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur