Kontron COMe-bEP7 Manuel utilisateur

 USER GUIDE

COMe-bEP7 Module

Doc.

Doc. ID: BEP7M102

COMe-bEP7 Module User Guide

This page has been intentionally left blank

COMe-bEP7 Module User Guide

www.kontron.com // 3

COME-BEP7 MODULE - USER GUIDE

Disclaimer

Kontron would like to point out that the information contained in this user guide may be subject

to alteration, particularly as a result of the constant upgrading of Kontron products. This

document does not entail any guarantee on the part of Kontron with respect to technical

processes described in the user guide or any product characteristics set out in the user guide.

Kontron assumes no responsibility or liability for the use of the described product(s), conveys

no license or title under any patent, copyright or mask work rights to these products and makes

no representations or warranties that these products are free from patent, copyright or mask

work right infringement unless otherwise specified. Applications that are described in this user

guide are for illustration purposes only. Kontron makes no representation or warranty that such

application will be suitable for the specified use without further testing or modification. Kontron

expressly informs the user that this user guide only contains a general description of processes

and instructions which may not be applicable in every individual case. In cases of doubt, please

contact Kontron.

This user guide is protected by copyright. All rights are reserved by Kontron. No part of this

document may be reproduced, transmitted, transcribed, stored in a retrieval system, or

translated into any language or computer language, in any form or by any means (electronic,

mechanical, photocopying, recording, or otherwise), without the express written permission of

Kontron. Kontron points out that the information contained in this user guide is constantly being

updated in line with the technical alterations and improvements made by Kontron to the

products and thus this user guide only reflects the technical status of the products by Kontron

at the time of publishing.

Brand and product names are trademarks or registered trademarks of their respective owners.

Kontron S&T AG

Lise-Meitner-Str. 3-5

86156 Augsburg

Germany

www.kontron.com

COMe-bEP7 Module User Guide

www.kontron.com // 4

Intended Use

THIS DEVICE AND ASSOCIATED SOFTWARE ARE NOT DESIGNED, MANUFACTURED OR INTENDED

FOR USE OR RESALE FOR THE OPERATION OF NUCLEAR FACILITIES, THE NAVIGATION, CONTROL

OR COMMUNICATION SYSTEMS FOR AIRCRAFT OR OTHER TRANSPORTATION, AIR TRAFFIC

CONTROL, LIFE SUPPORT OR LIFE SUSTAINING APPLICATIONS, WEAPONS SYSTEMS, OR ANY

OTHER APPLICATION IN A HAZARDOUS ENVIRONMENT, OR REQUIRING FAIL-SAFE PERFORMANCE,

OR IN WHICH THE FAILURE OF PRODUCTS COULD LEAD DIRECTLY TO DEATH, PERSONAL INJURY,

OR SEVERE PHYSICAL OR ENVIRONMENTAL DAMAGE (COLLECTIVELY, "HIGH RISK APPLICATIONS").

You understand and agree that your use of Kontron devices as a component in High Risk

Applications is entirely at your risk. To minimize the risks associated with your products and

applications, you should provide adequate design and operating safeguards. You are solely

responsible for compliance with all legal, regulatory, safety, and security related requirements

concerning your products. You are responsible to ensure that your systems (and any Kontron

hardware or software components incorporated in your systems) meet all applicable

requirements. Unless otherwise stated in the product documentation, the Kontron device is not

provided with error-tolerance capabilities and cannot therefore be deemed as being engineered,

manufactured or setup to be compliant for implementation or for resale as device in High Risk

Applications. All application and safety related information in this document (including

application descriptions, suggested safety measures, suggested Kontron products, and other

materials) is provided for reference only.

Handling and operation of the product is permitted only for trained

personnel within a work place that is access controlled. Please follow the

“General Safety Instructions for IT Equipment” supplied with the system.

COMe-bEP7 Module User Guide

www.kontron.com // 5

Revision History

Revision Brief Description of Changes Date of Issue Author

0.1 Initial issue 2021 April 21st MAG

1.01 Gate 4 document release 2022-02-08 MAG

1.02 Add notes to uEFI BIOS sections 2022-02-10 SH

1.03 Typo corrections 2022-04-19 MAG

Terms and Conditions

Kontron warrants products in accordance with defined regional warranty periods. For more

information about warranty compliance and conformity, and the warranty period in your region,

visit http://www.kontron.com/terms-and-conditions.

Kontron sells products worldwide and declares regional General Terms & Conditions of Sale,

and Purchase Order Terms & Conditions. Visit http://www.kontron.com/terms-and-

conditions.

For contact information, refer to the corporate offices contact information on the last page of

this user guide or visit our website CONTACT US.

Customer Support

Find Kontron contacts by visiting: http://www.kontron.com/support.

Customer Service

As a trusted technology innovator and global solutions provider, Kontron extends its embedded

market strengths into a services portfolio allowing companies to break the barriers of

traditional product lifecycles. Proven product expertise coupled with collaborative and highly-

experienced support enables Kontron to provide exceptional peace of mind to build and

maintain successful products.

For more details on Kontron’s service offerings such as: enhanced repair services, extended

warranty, Kontron training academy, and more visit http://www.kontron.com/support-and-

services/services.

COMe-bEP7 Module User Guide

www.kontron.com // 6

Customer Comments

If you have any difficulties using this user guide, discover an error, or just want to provide some

feedback, contact Kontron support. Detail any errors you find. We will correct the errors or

problems as soon as possible and post the revised user guide on our website.

COMe-bEP7 Module User Guide

www.kontron.com // 7

Symbols

The following symbols may be used in this manual

DANGER indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

WARNING indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION indicates a hazardous situation which, if not avoided,

may result in minor or moderate injury.

NOTICE indicates a property damage message.

Electric Shock!

This symbol and title warn of hazards due to electrical shocks (> 60 V)

when touching products or parts of them. Failure to observe the

precautions indicated and/or prescribed by the law may endanger your

life/health and/or result in damage to your material.

Please refer also to the "High-Voltage Safety Instructions" portion below in

this section.

ESD Sensitive Device!

This symbol and title inform that the electronic boards and their

components are sensitive to static electricity. Care must therefore be taken

during all handling operations and inspections of this product in order to

ensure product integrity at all times.

COMe-bEP7 Module User Guide

www.kontron.com // 8

HOT Surface!

Do NOT touch! Allow to cool before servicing.

This symbol indicates general information about the product and the user

manual.

This symbol also indicates detail information about the specific product

configuration.

This symbol precedes helpful hints and tips for daily use.

For Your Safety

Your new Kontron product was developed and tested carefully to provide all features necessary

to ensure its compliance with electrical safety requirements. It was also designed for a long

fault-free life. However, the life expectancy of your product can be drastically reduced by

improper treatment during unpacking and installation. Therefore, in the interest of your own

safety and of the correct operation of your new Kontron product, you are requested to conform

with the following guidelines.

High Voltage Safety Instructions

As a precaution and in case of danger, the power connector must be easily accessible. The

power connector is the product’s main disconnect device.

Warning

All operations on this product must be carried out by sufficiently skilled

personnel only.

Electric Shock!

Before installing a non hot-swappable Kontron product into a system

always ensure that your mains power is switched off. This also applies to

the installation of piggybacks. Serious electrical shock hazards can exist

during all installation, repair, and maintenance operations on this product.

Therefore, always unplug the power cable and any other cables which

provide external voltages before performing any work on this product.

Earth ground connection to vehicle’s chassis or a central grounding point

shall remain connected. The earth ground cable shall be the last cable to be

COMe-bEP7 Module User Guide

www.kontron.com // 9

disconnected or the first cable to be connected when performing

installation or removal procedures on this product.

Special Handling and Unpacking Instruction

ESD Sensitive Device!

Electronic boards and their components are sensitive to static electricity.

Therefore, care must be taken during all handling operations and

inspections of this product, in order to ensure product integrity at all times.

Do not handle this product out of its protective enclosure while it is not used for operational

purposes unless it is otherwise protected.

Whenever possible, unpack or pack this product only at EOS/ESD safe work stations. Where a

safe work station is not guaranteed, it is important for the user to be electrically discharged

before touching the product with his/her hands or tools. This is most easily done by touching a

metal part of your system housing.

It is particularly important to observe standard anti-static precautions when changing

piggybacks, ROM devices, jumper settings etc. If the product contains batteries for RTC or

memory backup, ensure that the product is not placed on conductive surfaces, including anti-

static plastics or sponges. They can cause short circuits and damage the batteries or conductive

circuits on the product.

COMe-bEP7 Module User Guide

www.kontron.com // 10

Lithium Battery Precautions

If your product is equipped with a lithium battery, take the following precautions when replacing

the battery.

Danger of explosion if the battery is replaced incorrectly.

Replace only with same or equivalent battery type recommended by the

manufacturer.

Dispose of used batteries according to the manufacturer’s instructions.

General Instructions on Usage

In order to maintain Kontron’s product warranty, this product must not be altered or modified in

any way. Changes or modifications to the product, that are not explicitly approved by Kontron

and described in this user guide or received from Kontron Support as a special handling

instruction, will void your warranty.

This product should only be installed in or connected to systems that fulfill all necessary

technical and specific environmental requirements. This also applies to the operational

temperature range of the specific board version that must not be exceeded. If batteries are

present, their temperature restrictions must be taken into account.

In performing all necessary installation and application operations, only follow the instructions

supplied by the present user guide.

Keep all the original packaging material for future storage or warranty shipments. If it is

necessary to store or ship the product then re-pack it in the same manner as it was delivered.

Special care is necessary when handling or unpacking the product. See Special Handling and

Unpacking Instruction.

Quality and Environmental Management

Kontron aims to deliver reliable high-end products designed and built for quality, and aims to

complying with environmental laws, regulations, and other environmentally oriented

requirements. For more information regarding Kontron’s quality and environmental

responsibilities, visit http://www.kontron.com/about-kontron/corporate-

responsibility/quality-management.

Disposal and Recycling

Table des matières

Autres manuels Kontron Unité de contrôle

Kontron

Kontron ADA-ETX-CD-FC4 Manuel utilisateur

Kontron

Kontron AM4011 Manuel utilisateur

Kontron

Kontron SMARC-sAMX7 Manuel utilisateur

Kontron

Kontron COMe-bSL6 Manuel utilisateur

Kontron

Kontron COMe-bKL6 Manuel utilisateur

Kontron

Kontron AM4100 Manuel utilisateur

Kontron

Kontron PC/104 VGALCD-6 Manuel utilisateur

Kontron

Kontron EPIC/CE Manuel utilisateur

Kontron

Kontron AM4150 Manuel utilisateur

Kontron

Kontron AM4520 Manuel utilisateur

Kontron

Kontron COMe-mAL10 Manuel utilisateur

Kontron

Kontron DIMM-PC ADA7 Manuel utilisateur

Kontron

Kontron SMARC sXAL Manuel utilisateur

Kontron

Kontron CP-RIO3-04S Manuel utilisateur

Kontron

Kontron COMe-cBT6 Manuel utilisateur

Kontron

Kontron COMe-mCT10 Manuel utilisateur

Kontron

Kontron CU 5 -2 Series Manuel utilisateur

Kontron

Kontron AdvancedTCA AM4330 Manuel utilisateur

Kontron

Kontron CP-RIO6-001 Manuel utilisateur

Kontron

Kontron ETX-LX2 Manuel utilisateur

Kontron

Kontron QSEVEN-Q7AL Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur