Konica Minolta PS 7000 Manuel utilisateur

Instructions for the book scanner Minolta PS 7000

1Starting scanner, computer & software

First, turn on the scanner (red power plug at the table and the switch on the left hand side

of the scanner), then turn on the PC!

The computer is within the Eawag network. Access to the Empa network is not possible.

For remarks on the file transfer refer to p.5.

Starting Windows 7: Username: eaguest

Password: eaguest

Double click the short cut SRZ ProScan on the desktop.

Enter Username Benutzername: eaguest

and password: Kennwort: eaguest

Select “Projektmode” if the SRZ ProScan software asks

you to choose a project (“Projekt wählen”),

then confirm the default selection for the target directory.

Push the orange button "Stapel beginnen" on the scanner’s

keyboard. Note that this step is omitted if the software has just been

April 2015

1 / 5

Lib4RI: Library for the Research Institutes within the ETH Domain: Eawag, Empa, PSI & WSL Eawag: Swiss Federal Institute of Aquatic Science and Technology

Empa: Swiss Federal Laboratories for Materials Science and Technology · PSI: Paul Scherrer Institute · WSL: Swiss Federal Institute for Forest, Snow and Landscape Research

started.

Write a name for your PDF in the box “Stapelname” (e.g.

"TESTSCAN-01") and press "Enter".

Place the book on the scanner board (straight to the upper border, with the pages to be

scanned facing up) and choose the appropriate size of the document indicated in the

middle of the board B4, B5, A4... (always choose the next larger size).

Enter the corresponding size with the light blue buttons on the left

hand side of the scanner’s keyboard (e.g. “B5 quer”).

Then press the yellow button "1 Rahmen".

2Scanning

Press the book gently with your fingers on its left and right side on the board. Start the

scanning process with either the left or the right long button on the board. You have to

press it quite hard.

After the scanning of the first page you have to adjust the green frame on the compu-ter’s

screen. Move, enlarge or reduce the frame by clicking on it (it will be red and can be

adjusted). The frame’s content is the content of the PDF page!

Attention: only what’s inside the frame is scanned and thus saved to the PDF!

After placing and scaling the frame correctly for the first page, it can

be duplicated by pressing the blue button "2 Rahmen“.

The active one of the two frames is always red, the other one is green (change their status

by clicking on them).

Placing and scaling one frame (“1 Rahmen”) first and then duplicating it by pressing the

“2 Rahmen“ button has the advantage that both frames, that is, both sides of the PDF,

will have the same size.

2 / 5

Lib4RI: Library for the Research Institutes within the ETH Domain: Eawag, Empa, PSI & WSL Eawag: Swiss Federal Institute of Aquatic Science and Technology

Empa: Swiss Federal Laboratories for Materials Science and Technology · PSI: Paul Scherrer Institute · WSL: Swiss Federal Institute for Forest, Snow and Landscape Research

Turn the page of the book and scan the subsequent pages. On the left side of the computer

screen the scanned pages are listed and can be selected, deleted or moved by clicking on

them (see more in the last section, p.5).

If the colour of the long buttons on the scanner board is red rather than green, the scanner

is in sleep mode and the button has to be pressed twice.

Attention: always double-check the computer screen to see if the scanned text

is within both frames. If not, rescale and replace the frames!

The scanner could report the following errors: Buchdicke nicht erkannt

Buch.zur.o.Blt.Scan.einst

Just ignore them and start again with the scanning of the pages. The button has to be

pressed twice.

3Finishing the scan

When you are finished with scanning push the orange key "Stapel

abschliessen“ to finish the scanning process. If this key does not

respond, as is the case if you did some scan corrections (see p.5), just

press F3 on the regular computer keyboard and confirm the

subsequent query to save your scan.

By pressing "Stapel beginnen" you can start with the scanning of

another book,

or you click on the minimize button in the top right edge of the

window of the “SRZ ProScan” program.

Please leave the computer and scanner turned on!

3 / 5

Lib4RI: Library for the Research Institutes within the ETH Domain: Eawag, Empa, PSI & WSL Eawag: Swiss Federal Institute of Aquatic Science and Technology

Empa: Swiss Federal Laboratories for Materials Science and Technology · PSI: Paul Scherrer Institute · WSL: Swiss Federal Institute for Forest, Snow and Landscape Research

4Where is the PDF-file?

Your scanned PDF file is stored locally on C in the directory “c:\ProScan Ablage“. Shortcut

on the desktop:

The folder „TESTSCAN-01“ contains the TIFF files of every single scanned page, and, at

the end, the whole PDF file.

here‘s the scanned document

the generated PDF-file

TIFF-files of

the scanned

pages

4 / 5

Lib4RI: Library for the Research Institutes within the ETH Domain: Eawag, Empa, PSI & WSL Eawag: Swiss Federal Institute of Aquatic Science and Technology

Empa: Swiss Federal Laboratories for Materials Science and Technology · PSI: Paul Scherrer Institute · WSL: Swiss Federal Institute for Forest, Snow and Landscape Research

5Access the PDF-file from your office computer

In order to access the PDF file from your own computer you have the following options:

Eawag

Copy the PDF to your personal scratch disk

(Q:\Diverses\Scratch-Disk).

Copy the PDF to \\lib4ri\scans$.

Empa

Copy the PDF to \\lib4ri\scans$.You can access this folder

via \\lib4ri.eawag.wroot.emp-eaw.ch\scans$.

Tip for Mac users: connect to the server via SMB (e.g. smb://lib4ri/scans$)

6Possible correction tools

Fingers holding the pages flat, holes, margins, shadows,... could be visible on the scan. All

this can be deleted. Further, askew pages can be straightened and the order of the pages

can be changed. However, it is best to scan all pages first and only at the end, but before

finishing the scanning process, to do the corrections.

On the left of the screen you see the pages consecutively numbered. They can be opened by

clicking on these numbers.

•With the right mouse button clicking on the respective page numbers on this list,

the pages can be deleted or their order changed by cutting one page and inserting it

at the desired place (if, e.g., one of the first pages had to be rescanned afterwards).

By pressing the right mouse button within the displayed page or via “Bildbearbeitung“

from the menu list, you can apply corrections, so, e.g.:

•Straighten the text with the commands “Deskew“.

•Erase unwanted shadows with the command "Radiergummi“.

5 / 5

Lib4RI: Library for the Research Institutes within the ETH Domain: Eawag, Empa, PSI & WSL Eawag: Swiss Federal Institute of Aquatic Science and Technology

Empa: Swiss Federal Laboratories for Materials Science and Technology · PSI: Paul Scherrer Institute · WSL: Swiss Federal Institute for Forest, Snow and Landscape Research

Table des matières

Autres manuels Konica Minolta Scanner

Konica Minolta

Konica Minolta BIZHUB 600 Manuel utilisateur

Konica Minolta

Konica Minolta II Manuel utilisateur

Konica Minolta

Konica Minolta PS7000C MKII Manuel utilisateur

Konica Minolta

Konica Minolta Q-SCAN Manuel utilisateur

Konica Minolta

Konica Minolta DiMAGE Scan Elite 5400 II Manuel

Konica Minolta

Konica Minolta BIZHUB C252 Manuel utilisateur

Konica Minolta

Konica Minolta IV Manuel utilisateur

Konica Minolta

Konica Minolta PW1-NS Manuel utilisateur

Konica Minolta

Konica Minolta SU-502 Manuel utilisateur

Konica Minolta

Konica Minolta bizhub PRESS C8000 Manuel utilisateur

Konica Minolta

Konica Minolta RX-II Manuel utilisateur

Konica Minolta

Konica Minolta bizhub 160 Manuel utilisateur

Konica Minolta

Konica Minolta PS5000C MKII Manuel utilisateur

Konica Minolta

Konica Minolta DR1600 Manuel utilisateur

Konica Minolta

Konica Minolta MS6000 MK II Manuel utilisateur

Konica Minolta

Konica Minolta MS 7000 Manuel utilisateur

Konica Minolta

Konica Minolta PS5000C MKII Manuel utilisateur

Konica Minolta

Konica Minolta PS5000C MKII Manuel utilisateur

Konica Minolta

Konica Minolta Fujitsu fi-6800 Manuel utilisateur

Konica Minolta

Konica Minolta BIZHUB PRO 1050 Manuel utilisateur

Konica Minolta

Konica Minolta SL1000 Microfiche Manuel utilisateur

Konica Minolta

Konica Minolta SL1000 Digital Film Scanner Manuel utilisateur

Konica Minolta

Konica Minolta Dimage Scan Elite 5400II Manuel utilisateur

Konica Minolta

Konica Minolta MS7000 MK II Manuel utilisateur

Manuels Scanner populaires d'autres marques

Plustek

Plustek Scanner Manuel utilisateur

Z/I Imaging

Z/I Imaging PhotoScan 2001 Manuel utilisateur

Renkforce

Renkforce DS100-5M Manuel utilisateur

Image Access

Image Access WideTEK A2 Manuel utilisateur

Canon

Canon imageFORMULA CR-120N Manuel utilisateur

Fujitsu

Fujitsu FI-4860C2 Manuel utilisateur

GeoSlam

GeoSlam ZEB Horizon Instructions d'installation

Kodak

Kodak i5800 Scanner Manuel utilisateur

Kodak

Kodak i7300 Manuel utilisateur

Revopoint

Revopoint POP Manuel utilisateur

Fujitsu

Fujitsu fi-4860C Manuel utilisateur

Eddyfi Technologies

Eddyfi Technologies Floormap X Manuel utilisateur

Faselase

Faselase F6 Manuel utilisateur

Fujitsu

Fujitsu CardMinder Manuel utilisateur

Uniden

Uniden BC340CRS Manuel utilisateur

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Manuel utilisateur

Mustek

Mustek PageExpress 4800 Pro Manuel utilisateur

Optex

Optex 750830 Manuel utilisateur