Kodak 8670 PS - CALIBRATION GUIDE Manuel utilisateur
CONTENTS
INDEX
SEARCH
HELP
Operator’s Guide
Printing
Guide
Color Management
Calibration
Getting Started
Easy Cal
Setting Preferences
and Using
Calibration Tables
Visual Gray Balance
Visual Linearity
Densitometer
Calibration
Network
Interface Guide
Getting Started
The
Kodak Digital Science
calibration utility (calibration utility) allows
your printer to produce the best possible color response. In simplest
terms, printer calibration adjusts the response of the printer so that a
specific data input value yields a specific color density output. When a
printer is properly calibrated, it generates the correct density for each
given data value. Calibration considers only a single primary color at a
time and measures the density for the primary color.
Density is one color aspect that can be easily and reliably measured, so
calibrating the Kodak Professional 8670 PS printer(8670 printer) is easy
and straightforward.
The calibration utility lets you select either a visual calibration process or
a more accurate densitometer calibration.
System Requirements
To use the calibration utility, your system must have the following
hardware and software:
Macintosh Systems
Recommended System Configuration
•
a 68040 or PowerPC processor
•
Apple Operating System 7.5 or higher software
CONTENTS
INDEX
SEARCH
HELP
Operator’s Guide
Printing
Guide
Color Management
Calibration
Getting Started
Easy Cal
Setting Preferences
and Using
Calibration Tables
Visual Gray Balance
Visual Linearity
Densitometer
Calibration
Network
Interface Guide
•
16 MB of RAM
•
color monitor
•
export module for the 8670 printer
•
densitometer if you will be doing the densitometer calibration procedure
Minimum System Configuration
•
68030 processor
•
Apple Operating System 7.1
•
8 MB of RAM
•
standard color or black and white monitor (minimum resolution 640 x
400 pixels
•
export module for the 8670 printer
•
densitometer if you will be doing the densitometer calibration
NOTE: The export module software for Macintosh systems is included on
the software CD that came with your printer. Windows Systems
Recommended System Configuration
•
486 or Pentium processor
•
MS-DOS version 6.22 or later
•
Microsoft Windows for workgroups 3.11 or Windows 95 software
•
16 MB of RAM
CONTENTS
INDEX
SEARCH
HELP
Operator’s Guide
Printing
Guide
Color Management
Calibration
Getting Started
Easy Cal
Setting Preferences
and Using
Calibration Tables
Visual Gray Balance
Visual Linearity
Densitometer
Calibration
Network
Interface Guide
•
4 MB of hard disk space
•
color monitor
•
export module for the 8670 printer
•
densitometer if you will be doing the densitometer calibration
Minimum System Configuration
•
386 processor
•
MS-DOS version 5.0 or later
•
Microsoft Windows 3.1, Windows for workgroups 3.11, or Windows 95
software
•
8 MB of RAM
•
4 MB or hard disk space
•
standard color or black and white monitor (standard VGA; minimum
resolution 640 x 480 pixels)
NOTE: The export module software for Windows systems is included on
the software CD that came with your printer.
Installing the Software for the Calibration Utility
The software for the calibration utility and the export module are included
on the CD that came with your printer. Install the CD in the CD-ROM
drive, and use the browser to locate and install the software.
CONTENTS
INDEX
SEARCH
HELP
Operator’s Guide
Printing
Guide
Color Management
Calibration
Getting Started
Easy Cal
Setting Preferences
and Using
Calibration Tables
Visual Gray Balance
Visual Linearity
Densitometer
Calibration
Network
Interface Guide
Getting Started with the Calibration Utility
Before you use the calibration utility, you should be thoroughly familiar
with how to operate the printer. If you plan to use the densitometer
calibration, you should be familiar with densitometry and how to operate
and calibrate your densitometer.
How Often To Calibrate
Calibrate your printer whenever the density or color balance of the prints
do not look correct.You may also want to calibrate your printer after it has
been serviced. Be sure that you calibrate for the correct media installed.
Calibrating your printer means calibrating the printing system—printer
and media.
Calibration Methods
The visual calibration components of the calibration utility include Easy
Cal, Visual Gray Balance, and Visual Linearity. While these methods do
not yield as accurate a result as a densitometer calibration, they can
make significant improvements in the consistency of results.
Easy Cal
—a five-step process to quickly calibrate your printer using the
Visual Gray Balance calibration. Refer to “Easy Cal”for instructions on
running an Easy Cal calibration.
CONTENTS
INDEX
SEARCH
HELP
Operator’s Guide
Printing
Guide
Color Management
Calibration
Getting Started
Easy Cal
Setting Preferences
and Using
Calibration Tables
Visual Gray Balance
Visual Linearity
Densitometer
Calibration
Network
Interface Guide
Visual Gray Balance
—calibrates your printer so that it produces a
neutral gray. Visual Gray Balance calibration ensures that the correct
percentages of cyan, magenta, and yellow dye are printed over the entire
tonal range to produce a neutral gray. Use the Visual Gray Balance
calibration if the color balance of your prints is not correct. Refer to
“Visual Gray Balance”for instructions on running a Visual Gray Balance
calibration.
Visual Linearity
—calibrates your printer for the correct lightness/
darkness.Visual Linearity ensures that your printer produces an accurate
representation of the requested density values over the entire tonal
range. Use the Visual Linearity calibration if the color balance is correct,
but the density is too dark or light. Refer to “Visual Linearity”for
instructions on running a Visual Linearity calibration.
Densitometer Calibration
A densitometer calibration calibrates your printer’s response based on the
densitometer reading for selected patches on a test print. Calibrating your
printer with a densitometer yields the most accurate calibration results for
color balance and density. Refer to “Densitometer Calibration”for
instructions on running a Densitometer calibration.
CONTENTS
INDEX
SEARCH
HELP
Operator’s Guide
Printing
Guide
Color Management
Calibration
Getting Started
Easy Cal
Setting Preferences
and Using
Calibration Tables
Visual Gray Balance
Visual Linearity
Densitometer
Calibration
Network
Interface Guide
Starting the Calibration Utility
The following steps describe how to start the calibration utility:
NOTE: The illustrations in this chapter show Macintosh system dialog
boxes. The dialog boxes for Windows are similar and have
identical functionality.
1.
Double-click on the icon for the calibration utility.
The calibration utility selection box opens.
2.
Do one of the following:
•
Click on
Begin Easy Cal
to launch Easy Cal,
or
•
Click on
Launch Normal Utility
to use the other calibration
procedures.
For information about the Normal Utility, refer to “Using the Normal
Utility to Calibrate Your Printer.” For more information on the
calibration utility selection box, refer to “Option Descriptions.”
CONTENTS
INDEX
SEARCH
HELP
Operator’s Guide
Printing
Guide
Color Management
Calibration
Getting Started
Easy Cal
Setting Preferences
and Using
Calibration Tables
Visual Gray Balance
Visual Linearity
Densitometer
Calibration
Network
Interface Guide
Using the Normal Utility to Calibrate Your Printer
The Normal Utility allows you to create a new calibration document or
start from a previously-saved calibration document.
When you click on
Launch Normal Utility
in the Calibration Utility
selection box, the Normal Utility calibration procedure starts up; and the
Printer Calibration Utility window opens.
NOTE: If this is the first time you have run the calibration utility, or there
are no printers on the Select Printer menu, or the Preferences
files have been deleted, you must select and open the export
module.
For information about creating a new calibration table, refer to
“Creating a New Calibration Document.” For information about
opening an existing calibration document, refer to “Using an Existing
Calibration Table as the Starting Point.”
CONTENTS
INDEX
SEARCH
HELP
Operator’s Guide
Printing
Guide
Color Management
Calibration
Getting Started
Easy Cal
Setting Preferences
and Using
Calibration Tables
Visual Gray Balance
Visual Linearity
Densitometer
Calibration
Network
Interface Guide
Easy Cal
Easy Cal provides you with the steps to guide you through the process of
calibrating your printer based on a Visual Gray Balance calibration.
NOTE: You cannot use Easy Cal to calibrate a printer with a black-only
ribbon.
For a description of the dialog boxes used in Easy Cal, refer to “Option
Descriptions.”
When you click on
Begin Easy Cal
in the Calibration Utility selection
dialog box, the Easy Cal calibration procedure starts up.
The Easy Cal dialog box appears.
•
Click on
Proceed
.
NOTE: Clicking on
Cancel
accesses the Normal Utility.
CONTENTS
INDEX
SEARCH
HELP
Operator’s Guide
Printing
Guide
Color Management
Calibration
Getting Started
Easy Cal
Setting Preferences
and Using
Calibration Tables
Visual Gray Balance
Visual Linearity
Densitometer
Calibration
Network
Interface Guide
Easy Cal Step 1
The Easy Cal Step1of 5 dialog box appears. This dialog box allows
you to select the printer model you wish to calibrate and locate the
folder containing the export module.
1.
Select the printer from the Printer Model drop-down list.
NOTE: If the printer you want to calibrate does not appear on the menu,
you must locate and select the export module for that printer.
2.
Click on
Locate Export Modules Folder
.
3.
In the file selection box that appears, locate and open the folder that
contains the export module:
•
On Macintosh systems, use the path System Folder:Applications
Support:Kodak:Plug-ins (Printing).
CONTENTS
INDEX
SEARCH
HELP
Operator’s Guide
Printing
Guide
Color Management
Calibration
Getting Started
Easy Cal
Setting Preferences
and Using
Calibration Tables
Visual Gray Balance
Visual Linearity
Densitometer
Calibration
Network
Interface Guide
•
On Windows systems, use the path C:\Windows\Kodak\Plugins
(Printing).
4.
Select the export module, and click on
Open
.You are returned to the
Easy Cal Step 1 of 5 dialog box.
5.
Click on
Next.
Easy Cal Step 2
The Easy Cal Step 2 of 5 dialog box appears.
1.
If you want to calibrate a different printer than the one that appears in
the Printer box, go to Step 2 in this procedure. If you do not need to
select a new printer, click on
Next
to go to Easy Cal Step 3 of 5.
2.
Click on
Select Printer
.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Kodak Imprimante
Kodak
Kodak Magnus VLF Q2400 Manuel utilisateur
Kodak
Kodak 8657 Manuel utilisateur
Kodak
Kodak NexPress 2500 Guide d'installation
Kodak
Kodak Apex 7015 Manuel utilisateur
Kodak
Kodak Color Ease PS Printer Manuel utilisateur
Kodak
Kodak 4800 Series Manuel utilisateur
Kodak
Kodak 8500 - USER'S GUIDE 240V Manuel utilisateur
Kodak
Kodak Dryview 5800 Manuel utilisateur
Kodak
Kodak 8650R THERMAL PRINTER Manuel
Kodak
Kodak Printe Manuel utilisateur
Kodak
Kodak DryView 8900 Manuel utilisateur
Kodak
Kodak ESP C310 Manuel utilisateur
Kodak
Kodak 400 II Manuel utilisateur
Kodak
Kodak 8660 - EXPORT MODULE GUIDE Manuel utilisateur
Kodak
Kodak DryView 6800 Manuel utilisateur
Kodak
Kodak 305 Manuel utilisateur
Kodak
Kodak 1200I Manuel de l'opérateur
Kodak
Kodak XL 7700 Manuel utilisateur
Kodak
Kodak 305 Manuel utilisateur
Kodak
Kodak DIGITAL MULTIPRINTER II - SITE Manuel utilisateur
