KMC Controls CSC-3501 Manuel utilisateur

Installation Guide

Linear Reset Volume Controllers

CSC-3501, 3505

Mounting

The CSC-3501 and 3505 are position sensitive. They are calibrated to be mounted in a horizontal plane

with the face down. Any other orientation will require recalibration of the “branch balance”.

1. Connect the right angle bracket to the mounting surface with 2 self threading screws in the two 13/64"

(5 mm) mounting holes.

2. Insert the controller, face down.

3. Make sure to leave enough room to make connections.

Connections

For model CSC-3501, 3505 use 1/4" (5 mm) O.D. “FR”

tubing, on the following push-on fittings:

1. Connect the clean, dry, main air supply to Port “M”.

2. Connect the damper actuator to Port “B”.

3. Connect the Thermostat output to Port “T”.

4. Connect the total pressure tap on the air flow sensor

to Port “H”.

5. Connect the static pressure tap on the air flow

sensor to Port “L”.

Adjustments and Calibration

Damper Action

The damper action is factory set at Normally Open (N.O.). To field select Normally Closed (N.C.):

1. Loosen damper selection screw

2. Turn selection dial clockwise until the “NC” arrow aligns with the “Damper” arrow.

3. Tighten selection screw.

To Adjust Branch Balance:

1. Disconnect thermostat from Port “T”

2. Disconnect ∆P sensor such that “H” and “L” are at 0" WC.

3. Adjust “LO STAT” knob fully Clockwise (CW)

4. Adjust branch balance for midpoint of actuator span +/- 2.5 psig (7.5 psi for 5–10 psi span,

10.5 psi for 8– 13 psi span).

5. Reconnect Ports “H”, “L” and “T”

KMC Controls

P.O. Box 497

19476 Industrial Drive

New Paris, IN 46553

574.831.5250

www.kmccontrols.com

221-019-01C

Adjustments and Calibration Continued

To Adjust Reset Start:

Thermostat Reset Start Point is factory Set at 8 psi.

1. Remove cap on Port “G” port

2. Connect to a 0– 30 psi gauge

3. Apply desired thermostat start point pressure to

Port “T”

3. Adjust “Reset Start” until gauge pressure increases

slightly (0.3 psig maximum).

4. Disconnect gauge and replace Port “G” cap

To Adjust Reset Span:

Thermostat Reset Span is factory set at 5 psig.

1. Remove Port “G” cap

2. Connect accurate 0–30 psi gauge.

3. Set thermostat for a Port “T” pressure of 15–30 psig.

4. Adjust “Reset Span” until gage pressure indicates the

desired span. This is total span pressure, not ending

pressure.

NOTE: An increase or decease of a 5 psig reset span will directly affect the differential pressure range.

Increasing the span to 7 psi will double the range, decreasing the span to 3.5 psi will halve the range.

5. Disconnect gauge and replace Port “G” cap

To Adjust Minimum and Maximum Limits:

1. Disconnect thermostat from Port “T” port

2 Adjust LO STAT ∆P:

For DA cooling or RA heating applications, adjust “LO STAT ∆P for minimum flow.

For RA cooling or DA heating applications, adjust “LO STAT ∆P” for maximum flow.

3. Set thermostat for a Port “T” pressure of 15–30 psig.

4. Adjust HI STAT ∆P:

For DA cooling or RA heating applications, adjust “HI STAT ∆P” for maximum flow.

For RA cooling or DA heating applications, adjust “HI STAT ∆P” for minimum flow.

NOTE:For maximum accuracy/repeatability, repeat/check minimum and maximum limit adjustments

twice. “LO STAT ∆P” must be adjusted first followed by “HI STAT ∆P” adjustment. “LO STAT ∆P”

adjustments affect “HI STAT ∆P” settings.

Maintenance

No routine maintenance is required.

Each component is designed and manufactured for

reliability and performance. Careful installation and

use will ensure long term dependability.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels KMC Controls Contrôleurs

KMC Controls

KMC Controls MEP-4201 Manuel utilisateur

KMC Controls

KMC Controls BAC-7401 Mode d'emploi

KMC Controls

KMC Controls AppStat Manuel utilisateur

KMC Controls

KMC Controls MEP-4201 Manuel utilisateur

KMC Controls

KMC Controls SimplyVAV BAC-8205 Manuel utilisateur

KMC Controls

KMC Controls BAC-5901C-AFMS Manuel utilisateur

KMC Controls

KMC Controls CTE-3017 Manuel utilisateur

KMC Controls

KMC Controls MEP-1500 Series Manuel utilisateur

KMC Controls

KMC Controls KMD-5831 Instructions d'utilisation d'origine

KMC Controls

KMC Controls MCP-1060 Series Manuel utilisateur

KMC Controls

KMC Controls SimplyVAV BAC-8001 Manuel utilisateur

KMC Controls

KMC Controls MEP-46 Q Series Manuel utilisateur

KMC Controls

KMC Controls MCP-1040 Series Manuel utilisateur

KMC Controls

KMC Controls BAC-7302 Mode d'emploi

KMC Controls

KMC Controls BAC-9300 Series Manuel utilisateur

KMC Controls

KMC Controls CEE-3009 Manuel utilisateur

KMC Controls

KMC Controls KMD-5210 Mode d'emploi

KMC Controls

KMC Controls CSC-2000 Series Manuel utilisateur

KMC Controls

KMC Controls CSC 3000 Series Guide de l'utilisateur

KMC Controls

KMC Controls CSC 3000 Series Guide de l'utilisateur

KMC Controls

KMC Controls CSC-1001 Manuel utilisateur

KMC Controls

KMC Controls KMD-5205 Mode d'emploi

KMC Controls

KMC Controls BAC-4000 series Guide de l'utilisateur

KMC Controls

KMC Controls MEP-3001 Mode d'emploi

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur