KMC Controls MEP-3001 Mode d'emploi

MEP-3001/3006 1 Installation and Operation Guide

Installation and Operation Guide

Thermic 2-Position or Time-Proportional Actuators

MEP-3001 (for VEP-12/22/34) and MEP-3006 (for VEP-11/21/37)

Mounting 1

Wiring 1

Operation 2

Maintenance 2

Select Speciﬁcations2

More Information 2 CAUTION

If mounting the actuator to a valve already in-line,

close the shut-off valves in the piping (upstream

ﬁrst, then downstream) or switch off the pump to

allow the differential pressure in the valve to drop.

CAUTION

To prevent condensation from dripping onto the

actuator housing, mount the valve with the actuator

in the upright position or, at most, at a 45° angle.

1a. On a new valve body, remove the protective cap

covering the bonnet. (See Illustration 2.)

1b. To remove an existing (same model) actuator,

disconnect the wiring, wait at least six minutes

until the actuator has completely cooled, turn

the actuator bayonet ring (coupling piece)

counterclockwise until it is loose, and pull o the

actuator. Also unscrew the old black bayonet nut

if it stays on.

2a. If the new black bayonet nut is loose from the

new actuator, screw it on top of the valve body

and rmly hand-tighten (only). (See Illustration

3.) Then place the actuator over it and turn the

actuator bayonet ring clockwise until it is hand-

tight and locks into place.

2b. If the new black bayonet nut is rmly aached

inside the actuator, screw the entire actuator on

top of the valve body until it is hand-tight and

locks into place.

Mounting

Wiring

Connect the brown wire to the phase side of 24 VAC

and the blue wire to neutral. (See Illustration 1.)

For two-position control, a simple switch or relay

can be used. For time-proportional (pulse-width

modulation) control, use a KMC REE-5017 or

REE-4106/5106 relay module. (See the relevant relay

module documentation for more information.)

NOTE: All wiring must conform to NEC and

local codes and regulations. Use a Class 2

transformer.

Illustration 1—Dimensions and Wiring

Illustration 2—Removing a Protective Cap

Illustration 3—Installing the Black Bayonet Nut

Brown to 24 VAC Phase

Blue to 24 VAC Neutral

MEP-3001/3006 2 Installation and Operation Guide

KMC Controls, Inc.

19476 Industrial Drive

New Paris, IN 46553

574.831.5250

www.kmccontrols.com; [email protected]

Maintenance

These actuators are noise-free and maintenance-free.

Careful installation will help ensure long-term reli-

ability and performance.

Operation

After the mechanical and electrical installations have

been completed, cycle the actuator to verify opera-

tion. (See Illustrations 4 and 5.)

When power is applied to the actuator, the tem-

perature of the heating element rises, causing the

solid expansion medium to expand and stroke the

aached valve body. The valve starts to open after

preheating for approximately 1 minute if the heating

element is switched on in a cold (room temperature)

state, and achieves the maximum stroke after (ap-

proximately) another 3-1/2 minutes. At power-o,

the expansion element cools down, and the spring

closes the valve.

De-energized position (gap closed):

• For MEP-3001s, the actuator shaft

is extended and the valve is closed.

• For MEP-3006s, the actuator shaft

is retracted and the valve is open.

(Fully) energized position (gap open):

• The MEP-3001 has been connected

to the power supply for at least

4-1/2 minutes. The actuator shaft is

retracted and the valve is open.

• The MEP-3006 has been connected

to the power supply for at least

4-1/2 minutes. The actuator shaft is

extended and the valve is closed.

Select Speciﬁcations

Power 24 VAC (± 20%), 50/60 Hz,

Class 2 only, 6 VA max.

Control Two-position or time-propor-

tional

Primary Fuse Must supply externally

Nominal Force 22.5 in-lb. (100 N•m)

Stroke Maximum 0.18 inches (4.5 mm)

Positioning Time 270 sec. @ 68° F (20° C)

Weight 0.4 lb. (0.18 kg)

Mounting Location NEMA 3 (IP54), interior only

Approvals Conforms to CE requirements

De-energized Position

MEP-3001 (NC) Actuator shaft extended, valve

closed (for VEP-12/22/34 se-

ries)

MEP-3006 (NO) Actuator shaft retracted, valve

open (for VEP-11/21/37 series)

Temperature Limits

Medium 34 to 230° F (1 to 110° C)

Ambient 41 to 122° F (5 to 50° C) @ 0 to

85% RH (non-condensing)

Shipping –4 to 140° F (–20 to 60° C) @ 0

to 95% RH (non-condensing)

Illustration 4—Position Indication

Illustration 5—Opening and Closing Times

More Information

For more information

on applications, see the

REE-5017 on the KMC

web site.

See also, the REE-5106.

Ce manuel convient aux modèles suivants

Autres manuels KMC Controls Contrôleurs

KMC Controls

KMC Controls CSC 3000 Series Guide de l'utilisateur

KMC Controls

KMC Controls MEP-4201 Manuel utilisateur

KMC Controls

KMC Controls KMDigital KMD-5290E Mode d'emploi

KMC Controls

KMC Controls BAC-9001CE Manuel utilisateur

KMC Controls

KMC Controls SimplyVAV BAC-8205 Manuel utilisateur

KMC Controls

KMC Controls KMD-5831 Instructions d'utilisation d'origine

KMC Controls

KMC Controls BAC-7003 Manuel utilisateur

KMC Controls

KMC Controls FlexStat BAC-120063CW-ZEC Manuel de l'opérateur

KMC Controls

KMC Controls MCP-1060 Series Manuel utilisateur

KMC Controls

KMC Controls KMD-5210 Mode d'emploi

KMC Controls

KMC Controls BAC-5901C-AFMS Manuel utilisateur

KMC Controls

KMC Controls MEP-7 Series Guide de l'utilisateur

KMC Controls

KMC Controls BAC-7401 Mode d'emploi

KMC Controls

KMC Controls CSP-4702 Manuel utilisateur

KMC Controls

KMC Controls MEP-4 Series Guide de l'utilisateur

KMC Controls

KMC Controls CTE-3017 Manuel utilisateur

KMC Controls

KMC Controls KMD-5205 Mode d'emploi

KMC Controls

KMC Controls MEP-1500 Series Manuel utilisateur

KMC Controls

KMC Controls SimplyVAV BAC-8001 Guide de l'utilisateur

KMC Controls

KMC Controls MEP-4201 Manuel utilisateur

KMC Controls

KMC Controls AppStat Manuel utilisateur

KMC Controls

KMC Controls BAC-4000 series Guide de l'utilisateur

KMC Controls

KMC Controls MCP-1040 Series Manuel utilisateur

KMC Controls

KMC Controls BAC-5900 Series Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur