Klearbar Mini Mode d’emploi

KLEARBAR MINI COUNTERTOP WATER DISPENSER

INSTALLATION / USER MANUAL

Dear customer,

We know you have multiple

options and thank you for

choosing the best.

KlearBar - For home and oce.

Clearly the right call anytime.

Index

Overview & diagram 06

Installation 07

User Maintenance 12

Safety Instructions 17

Technical specications 18

Troubleshooting 20

Blue bar

Orange bar

Silver bar

Red bar Green bar Yellow bar

Cream barWhite bar Black bar

WHAT’S YOUR

FAVORITE COLOR?

1. Touchscreen operation panel

2. Front panel indicator light:

Blue - COLD water

Red - HOT water

Purple - ENERGY SAVE mode

(Energy save mode will start after

4hours of non-use. Touch any key

to bring system to normal operation)

3. Faucet

4. Removable drip tray

5. Removable top panel

6. On/O cold water compressor and

delivery pump

7. On/O hot water tank

8. Water overow line outlet

9. Water line inlet (insert included

1/4 stem)

6 75

Touch screen instructions / user guide

1. Hot water activation icon

2. Tank rell activation icon

3. Cold water activation icon

4. UV light activation icon (Mini2only)

For HOT water dispense touch and

release #5, then touch and hold #6

For COLD water dispense touch and hold #

Overview & Diagram

1. Touchscreen operation panel

2. Front panel indicator light:

Blue - COLD water

Red - HOT water

Purple - ENERGY SAVE mode

(Energy save mode will start after

4hours of non-use. Touch any key

to bring system to normal operation)

3. Faucet

4. Removable drip tray

5. Removable top panel

6. On/O cold water compressor and

delivery pump

7. On/O hot water tank

8. Water overow line outlet

9. Water line inlet (insert included

1/4 stem)

ALWAYS PLUG KLEARBAR MINI ELECTRICAL CORD INTO A GFCI PROTECTED POWER OUTLET

There are multiple ways to connect your Klearbar Mini but regardless of your choice it

is recommended to follow local plumbing codes or consider hiring a licensed plumber.

But should you decide to DIY (do it yourself) we have provided a basic blueprint to get

you on your way.

Perhaps the easiest connection is to an existing water line already provided by your

refrigerator ice maker. Use a 1/4 union tee for this connection.

Installation & Maintenance

Your Klearbar Mini comes standard with virtually everything you need for a simple

water line connection:

• Installation/User manual

• 15 feet of food grade, 1/4 polyethylene tubing

• 45 psi pressure reducer (pre-installed inside water dispenser)

• Angle stop valve (mains connector)

• 1/4 union tee (install if using existing ice maker water line connection)

• 1/4 stem elbow (install at water line inlet)

You may also need the following items to assist your installation:

• Adjustable wrench to install angle stop valve

• Teon plumbers tape (use when installing angle stop valve)

• Plastic tubing cutter or scissors

• 3/8 inch drill bit and drill (if needed to drill hole in cabinetry to hide water line)

Connect 1/4 tubing into 1/4 stem elbow.

Connect 1/4 stem elbow into water line inlet port

Connect 1/4 tubing into 1/4 union tee inserted into

refrigerator water feed line

1/4 stem elbow1/4 union tee

Connect To Existing Refrigerator Ice Maker Water Line

- use the included 1/4 union tee when connectingto a 1/4

water mains connection or, use a brass compression

union tee if desired (always use a plastic compression

ferrule when connecting polyethylene

tubing using a brass

union - a brass compression ferrule may

cut into the plastic

tubing and cause a leak).

BEFORE PLUGGING IN TO ELECTRICITY turn o water line supply to refrigerator

ice maker.

Using a plastic tube or copper line cutter, make a square cut of the existing ice maker

water line no closer than

inches from where the water line originates from the oor

or wall, and insert the

1/4

union tee here. It may be good to have a large towel nearby as

a small amount of residual water may spray and drain out once the line is cut . Connect

one end of the included

1/4

polyethylene tubing to the

1/4

union tee.

Place the Klearbar Mini within a few feet of an available GFCI electrical socket and

connect the included

1/4

stem elbow into the water inlet port on the back of the unit

(be careful not to connect to the optional overow port). Now connect the opposite

end

1/4

polyethylene water line into the

1/4

elbow behind the Klearbar Mini. Trim o

extra water line as needed for a professional look.

Remove moisture absorbing

desiccant bag

Desiccant bag removed

(1 piece)

Install an optional

1/4

turn ball valve (not included; available at most hardware stores)

about

inches from the

1/4

stem elbow enabling easy water on/o access without

having to pull the refrigerator away from the wall. This is very convenient should you

ever need to remove the Klearbar Mini for cleaning or should you discover a leak.

BEFORE TURNING ON WATER LIFT RESERVOIR COVER THEN REMOVE

MOISTURE ABSORBING DESICCANT BAG INSIDE RESRVOIR. ALSO REMOVE

PROTECTIVE FOAM INSERTS (

) FROM THE ELECTRONIC FLOAT SWITCH

(KLEARBAR MINI

ONLY) INSIDE THE RESERVOIR.

BEFORE TURNING ON WATER PLACE HOT WATER SWITCH TO OFF POSITION

and then plug the Klearbar Mini into a GFCI receptacle. Open the water connection

and allow to reservoir to ll up. When the reservoir is full prime the water pump by

dispensing 10 ounces of water from both the cold and hot water tanks. Only after

priming is it now safe to turn on the cold and hot water switches on the rear of the

equipment.

Connect To Main beneath a Sink

Turn o COLD water supply beneath sink.

Use a wrench and disconnect the copper or braided riser tube connected to the

stop valve already threaded or soldered to the copper water main.

Thread the Klearbar angle stop valve (mains connector) OR OPTIONAL TEE

ADAPTOR (purchased separately) by rst wrapping Teon tape (not included) around

the newly exposed thread of the stop valve plumbed to the cold water main. Hand-

tighten then snugly tighten using a wrench.

Then apply Teon tape to downstream thread and reconnect the riser tube.

Before tee adaptor After tee adaptor installedTee adaptor installed

Use the included

1/4

polyethylene tubing and connect to the Klearbar angle stop

valve (or optional tee adaptor). First slide nut then compression ring onto tubing, and

then insert tubing insert into end of plastic tube. Now attach plastic tubing to Teon

taped thread.

Next drill a

3/8

hole through sink or countertop near the nal resting place of

the Klearbar Mini. Be extremely careful if drilling through a porcelain/cast iron sink

or granite countertop as damage may result. Consult a professional if unsure with

this procedure. Also consider drilling hole(s) behind cabinet drawers leading to side

opening of cabinet versus top opening of countertop.

Place the Klearbar Mini within a few feet of an available GFCI electrical socket and

connect the included

1/4

stem elbow into the water inlet port on the back of the unit

(be careful not to connect to the optional overow port). Now pull the

1/4

water line

through the drilled hole(s) and connect into the

1/4

stem elbow at rear of Klearbar Mini.

Install an optional

1/4

turn ball valve (not included; available at most hardware stores)

about

inches from the

1/4

stem elbow enabling easy on/o access. This is very

convenient should you ever need to remove the Klearbar Mini for cleaning or should

you discover a leak.

Turn on mains valve and check for leaks.

MAKE SURE THE HOT WATER SWITCH IS IN THE OFF POSITION BEFORE

PLUGGING IN to a GFCI receptacle. Allow to completely ll. Once full the Klearbar

Mini will automatically stop lling with water.

10.

Dispense at least 10 ounces of water from both the hot and cold tanks. It is now safe

to turn on the hot and cold water tanks.

WARNING: TURNING ON THE HOT WATER TANK BEFORE COMPLETELY FULL MAY

RESULT IN TRIPPING THE HOT TANK OVERLOAD PROTECTOR SWITCH (WATER

WILL NOT HEAT). IF THIS HAPPENS TURN OFF WATER CONNECTION, UNPLUG

UNIT AND CONTACT YOUR SERVICING DEALER FOR ASSISTANCE.

Autres manuels pour Mini

Table des matières

Autres manuels Klearbar Distributeur d'eau

Klearbar

Klearbar Mini Mode d’emploi

Manuels Distributeur d'eau populaires d'autres marques

Monarch Water

Monarch Water ULTIMATE MINI AQUA HE Manuel utilisateur

Haier

Haier HLM-109B Manuel utilisateur

abc

abc Fleck 5600SXT Manuel utilisateur

GE GXOF18G Mode d'emploi

Kenmore

Kenmore 625.385560 UltraFilter 650 Manuel utilisateur

Innova

Innova CEV+ Guide de démarrage rapide

Aries

Aries Hydra DI Manuel

GE GNCF02H Manuel utilisateur

ProFlo

ProFlo PFB Series Manuel utilisateur

Hydrotech

Hydrotech 89DF HIM Manuel utilisateur

A.O. Smith

A.O. Smith FREZYA 300S Manuel utilisateur

Frakco

Frakco Travelsoft RV 2400HD Manuel utilisateur

GE GXSF30V Mode d'emploi

Avanti

Avanti WD31EC Manuel utilisateur

Avanti

Avanti WD360 Manuel utilisateur

BRIO

BRIO CLCTTL520 Guide de l'utilisateur

3M HCD-1 Manuel utilisateur

Elkay

Elkay EFHFA8_2CJO Manuel d'installation