KitchenAid KCIP 1010/I Manuel utilisateur

KCIP 1010/I

KCIP 1210/I

Instructions for use

Warnings 4

Safeguarding the environment 5

Instructions for installation and use 6

Extraction modes 6

Installation 7

Hood description 14

Functioning 14

Maintenance 15

After-Sales Service 17

• This appliance should not be used by children or people with limited physical or mental

abilities and with no experience or knowledge of its use, unless they are supervised by

someone in charge of their safety or who has taught them how to use the appliance.

• Children should not play with the appliance.

1. Do not connect the appliance to the mains supply until the installation is completely finished.

Before carrying out any cleaning or maintenance work, always disconnect the hood from the mains

supply by pulling out the plug or turning off the mains switch in the house.

2. Do not flambé food under the hood since the flames generated could cause a fire.

3. Do not leave a frying pan unattended when frying food as the cooking oil could catch fire.

4. Constant cleaning and maintenance of your hood will ensure it works properly. Regularly remove all the

ingrained food from dirty surfaces. Regularly remove and clean or change the filter. Do not use

inflammable material to convey exhaust air.

5. If the hood is used in conjunction with other appliances that run on gas or other fuels, the negative

pressure of the room should be no greater than 4Pa (4 x 10-5 bar). This is why you should make sure

the room is well aired.

6. Exhaust air from the hood should not be eliminated through the heating system chimney or appliances

that run on gas or other fuels.

7. The room should be sufficiently ventilated when the hood is used together with other appliances that

run on gas or other fuels.

8. Before touching the light bulbs, make sure they have cooled down.

Note: always use gloves when installing or carrying out maintenance work.

Electrical connection

The mains voltage should correspond with the voltage shown on the specifications label found inside the

hood. If there is no plug, connect the hood to a socket that complies with current legislation and is in an

easily accessible location. If there is no plug (direct connection to the mains supply) or the plug is not in an

easily accessible location, fit a legally complying bi-polar switch that ensures the complete disconnection of

the mains in the event of a category III line surge, in compliance with the installation regulations.

IMPORTANT: before reconnecting the hood circuit to the power supply, check that it is

working properly, that the mains cable has been properly fitted and that it has NOT been

crushed in its holder during installation.

Cleaning the hood

Warning! Failure to remove oil/grease (at least once a month) could lead to a fire breaking out. Use a soft

cloth and mild cleaning product. Never use harsh substances or alcohol.

Before using the hood

To get best performance from the hood, please read these user instructions carefully and keep them for

future reference.

Keep the packaging material (plastic bags, pieces of polystyrene, etc.) out of children’s reach as they can be

dangerous.

Make sure the hood has not been damaged during transportation.

The installation and the electrical connections, replacement of power cables with plug or flexible cable

should be carried out by a qualified technician in compliance with current legislation in force.

This appliance was designed to be used by adults.

Warnings

1. Packing

The packaging material is entirely recyclable and marked with the recycling symbol . Follow local

regulations for scrapping. Keep the packaging materials (plastic bags, polystyrene parts, etc.) out of reach

of children, as they are potentially dangerous.

2. Product

This appliance is marked according to the European Directive 2002/96/EC, Waste Electrical and Electronic

Equipment (WEEE).

By ensuring that this product is disposed of correctly, you will help prevent potentially negative

consequences for the environment and human health.

The symbol on the product or on the documents accompanying the product indicates that this

appliance may not be treated as household waste. Instead, it should be handed over to the applicable

collection point for the recycling of electrical and electronic equipment.

Disposal must be carried out in accordance with local environmental regulations for waste disposal.

For more detailed information on treatment, recovery and recycling of this product, contact your local

authority, the household waste disposal service or the shop where you purchased the product.

Safeguarding the environment

Declaration of conformity

This product has been designed, manufactured and marketed according to the following:

- safety objectives of the “Low Voltage” Directive 2006/95/CE (which replaces 73/23/CEE and

subsequent amendments).

- protection requirements of “EMC” Directive 89/336/EEC amended by Directive 93/68/EEC.

Troubleshooting guide

Hood does not work:

• Is the electrical power supply switched on?

• Is there a power failure?

Insufficient suction power:

• Did you set the right speed?

• Do the filters need to be cleaned or replaced?

• Are the air outlets blocked?

Light does not work:

• Does the bulb need to be replaced?

• Is the bulb correctly fitted?

Warnings

This is an excessively heavy product and the movement and installation of the hood should be done by at

least two or more people.

Follow the instructions in this manual carefully. The manufacturer denies all responsibility for damage

or fire to the appliance resulting in failure to comply with the instructions in this manual.

Instructions for installation and use

The hood is designed to be used in two

modes: Venting exhaust fumes to the

outside, or by passing the air through a

charcoal filter before recirculating the air

back into the kitchen.

Vented Mode

The hood comes with an upper air outlet

Bfor the discharge of fumes to the

outside (vented exhaust pipe and fixing

straps are not supplied). Fig. 1

Recirculation Mode

If the fumes and steam from cooking

cannot be discharged towards the

outside, you can use the recirculation

mode by fitting an activated carbon filter

(not supplied, this must be purchased

seperately) and the deflector Fon the

support (bracket) G; the fumes and steam

are recirculated via the upper grid Hand

an exhaust pipe, connected to the upper

air outlet Band the connection ring fitted

to the deflector F(venting exhaust pipe

and fixing straps are not supplied). Fig. 2

Installation

The minimum distance between the

upper pan support surfaces on the

cooking appliance and the lowest part of

the cooker hood should be no less than

50 cm in the case of electrical cookers

and 70 cm in the case of gas or mixed

cookers. If the installation instructions for

the gas cooking appliance specify a greater

distance, then follow that instruction.

Extraction Modes

The hood comes with plugs suitable for most

walls/ceilings. You should however consult a

qualified technician to make sure the installation is

suitable for your kind of wall/ceiling. The wall/roof

should be sufficiently strong to support the weight

of the hood.

Before installation:

• Check that the product purchased is the right

size for the area where it is to be installed.

• To make installation easier, temporarily remove

the parts that block access to the fixing areas

(e.g.: grease filters, perimetric suction panels

and carbon filter support frames, depending on

which model you have).

• Remove the active carbon filter/s if provided

(again consult relative paragraph). This/these

should be re-assembled only if you wish to use

the hood in the extraction mode.

• Check that there are no parts (e.g. bags with

screws, warranty) inside of the hood (for

transport reasons). If there are, remove them

and put to the side.

• If possible, disconnect and remove the

surrounding units and those near the installation

area of the hood so that you have better

accessibility to the ceiling / wall where the hood

is to be installed. Otherwise, protect the units

as much as possible and all the parts relating to

the installation. Choose a flat surface and cover

it with some protection where you can place

the hood and parts.

• Furthermore, check that near the area where

you are installing the hood (in an area accessible

even when the hood is fitted) there is an

electric socket and that you can connect to an

venting pipe to the outside (In the Vented

mode only).

• Disconnect the electrical power from the

electrical socket connected to the hood at the

main switchboard and remember not to

connect the hood to the mains supply before

completing installation.

• Carry out all the building work necessary (e.g.:

installation of an electrical plug and/or holes to

pass the exhaust venting pipe through).

Fig. 3

• Establish the most suitable distance from the

work surfaces according to your needs

(Important! Respect the minimum distances

specifically indicated in this instruction booklet).

• Adjust the extension of the hood’s support

structure using the mathematical formula shown

in the diagram.

Note: only if you wish to use the hood in

recirculation mode (see also fig. 4 and later

paragraphs): in the case of highly extended

structures, before final assembly remember to

install the deflector so that it will be easier to

handle.

• Fit the two sections of the structure with a total

of 16 screws (8 per side).

Installation

T recirculation

mode

SIDE VIEW

Deflector

Connection

ring

Exhaust

Vent

Pipe

Recirculation mode only

Fig. 4

• Recirculation mode only: fix the deflector to the

frame:

a. Insert the deflector from one side of the

frame so that the rectangular hole at the centre

is facing downwards.

b. Fit the deflector with 4 screws from the top

of the frame.

c. Connect a suitable extraction pipe to the

connection ring provided. It should be long

enough ( with a diameter of 150mm) to reach

the connection ring on the motor unit when it is

installed. Use the mathematical formula in the

diagram to do this.

d. Insert the pipe with the connection ring

upwards and fix it to the deflector with 2 screws.

Installation

vented

mode

Vented mode only

Fig. 5

• Attach the ceiling perforation layout onto the

ceiling (the centre of the layout should

correspond with the centre of the hob and the

sides should be parallel to the sides of the hob –

the side of the layout with the words FRONT

on it corresponds to the side of the control

panel). Prepare the electrical connection.

• Make a hole as shown (4 holes for 4 wall plugs).

Insert the 4 plugs into the holes. Screw in 2

screws into the side holes (right and left),

leaving a space between the screw head and the

ceiling of about 1cm.

These screws will act as a hook for the support

structure.

Fig. 6

• Remove the power cable from the connection

box on the motor unit.

• Connect up the electricity on the ceiling within

the tolerance limits indicated on the template.

• Vented mode only: Install a suitable extraction

vent pipe (with a diameter of 150mm) that is

long enough to reach the connection ring on the

motor unit, when installed.

Use the mathematical formula in the diagram to

do this.

Installation

Fig. 7

• Hook the frame to the 2 screws on the ceiling

and fit securely with another 2 screws (front

and back). TIGHTEN ALL THE SCREWS

WELL.

Fig. 8

• Chimney size: the flue comes in a standard

length and can be cut to size.

Note: The height of the flue should be the

same as the frame extension (see the

mathematical formula in Fig. 3)

• Insert the flue in the frame, check that the

welded side is turned to the back (the opposite

side from where the hood control panel will be

when installation is complete). Fit with 2

screws.

Fig. 9

• Hook the motor unit onto the frame on 4

screws previously screwed onto the unit.

Warning! Pass the electrical cable through the

motor unit so that it does not get damaged and

so that it is possible to connect to the electrical

connection box.

Note: the side with the electrical connection

box corresponds with the side (FRONT) where

the control panel will be once the hood has

been installed.

• Securely attach with 2 screws and tighten all 6

screws.

• Connect the power cable to the connection box

and close the box again.

• Connect the extraction vent pipe to the union

ring on the unit.

Installation

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels KitchenAid hotte de ventilation

KitchenAid

KitchenAid KICU460WSS0 Instructions d'utilisation

KitchenAid

KitchenAid KXW9748YSS0 Fiche d'information produit

KitchenAid

KitchenAid KHVU781RSS1 Manuel utilisateur

KitchenAid

KitchenAid KIRD802XSS0 Manuel utilisateur

KitchenAid

KitchenAid KIRD801XSS0 Manuel utilisateur

KitchenAid

KitchenAid 36" (91.4 cm) and 48" (121.9 cm) Manuel

KitchenAid

KitchenAid KICU265H Instructions d'utilisation

KitchenAid

KitchenAid KWCU360JSS1 Manuel

KitchenAid

KitchenAid KXW8730YSS0 Fiche d'information produit

KitchenAid

KitchenAid KVUB600DSS Fiche d'information produit

KitchenAid

KitchenAid KIRD802HSS1 Manuel utilisateur

KitchenAid

KitchenAid KIRD862VSS0 Fiche d'information produit

KitchenAid

KitchenAid KVWC956KSS Manuel utilisateur

KitchenAid

KitchenAid KIRD801V Instructions d'utilisation

KitchenAid

KitchenAid RANGE HOOD LINER with INTERNAL BLOWER Manuel d'utilisation et d'entretien

KitchenAid

KitchenAid W10153151 Fiche d'information produit

KitchenAid

KitchenAid 4329223 Manuel

KitchenAid

KitchenAid KXW4436YSS Fiche d'information produit

KitchenAid

KitchenAid KHTU160KBL1 Manuel utilisateur

KitchenAid

KitchenAid KitchenAid KVUC600KSS0 Manuel

KitchenAid

KitchenAid UXG7360VDS0 Manuel utilisateur

KitchenAid

KitchenAid KHTU705SSS0 Manuel utilisateur

KitchenAid

KitchenAid KHLU162MSS0 Manuel utilisateur

KitchenAid

KitchenAid KIRD801VSS0 Manuel utilisateur

Manuels hotte de ventilation populaires d'autres marques

emmeti

emmeti RECUPA MED A-140 Mode d’emploi

Nibe

Nibe F135 Manuel utilisateur

Kuppersberg

Kuppersberg INTRO 60 Instructions d'installation et d'entretien

Zephyr

Zephyr Spruce AK9834BS Guide d'installation

Hisense

Hisense MH6INBG Manuel utilisateur

Miele

Miele DA 1255 Manuel utilisateur

Broan

Broan 46000 Manuel utilisateur

GE Profile PV977 Instructions originales

FALMEC

FALMEC FFRIA24W5FS Manuel utilisateur

Whirlpool

Whirlpool RH2600XL-1 SERIES Manuel utilisateur

Küppersbusch

Küppersbusch DX ISLA Manuel utilisateur

ETNA

ETNA AV360RVS Manuel utilisateur

JUNO

JUNO JDF603E6 Manuel utilisateur

Miele

Miele DA 6708 D Manuel utilisateur

Tricity Bendix

Tricity Bendix LE 150 Manuel

AEG

AEG X68163BV1 Manuel utilisateur

AEG

AEG 125 D Manuel utilisateur

Smeg

Smeg KSEV97X Manuel utilisateur