Kingston Technology DataTraveler 2000 Manuel utilisateur

Installation Guide

DataTraveler®2000

Find the language and latest documentation for DT2000 here.

DT2000 Installation Guide

Simplied Chinese .....

Traditional Chinese ....

............For instructions in English

. . . . . . . . . . . . . . . . . . Para instrucciones en Español

.........Für Anleitungen in Deutsch

. . . . . . . . . . . . . . . . . . Pour des instructions en Français

. . . . . . . . . . . . . . . . . . Per le istruzioni in Italiano

............Por as instruções em Português

. . . . . . . . . . . . . . . . . . Instrukcje w języku Polskim

. . . . . . . . . . . . . . . . . . Для инструкции на русском

. . . . . . . . . . . . . . . . . . Turkce talimatlar icin

. . . . . . . . . . . . . . . . . . Japanese

. . . . . . . . . . . . . . . . . . Thai

. . . . . . . . . . . . . . . . . . Vietnamese

Document No. 480ADT2000.A00

DT2000

Page 1 of 17

DataTraveler®2000 - User Manual

Remember to save your PIN in a safe place. If you lose or forget your

PIN, there is no way to access the data stored on the Kingston

DataTraveler®.

If you are having difficulty, please refer to this complete user guide loaded on your

DT2000, also available at Kingston’s website: kingston.com/support

DataTraveler®2000 incorporates DataLock®Technology licensed from ClevX, LLC.

trademarks are the property of their respective owners.

Document No. 480ADT2000.A00

DT2000

Page 2 of 17

Table of Contents

System Requirements ......................................................................................................... 3

Introduction.......................................................................................................................... 4

1. DT2000 layout ..................................................................................................................... 5

2. LED indicators and their actions.......................................................................................... 5

3. How to use the DT2000 for the first time............................................................................. 6

4. How to change the User PIN............................................................................................... 6

5. How to enable Options ........................................................................................................ 7

6. How to enable Read-Only Mode ......................................................................................... 8

7. How to enable Read/Write Mode ........................................................................................ 8

8. How to set the Timeout Lock Mode..................................................................................... 9

9. How to disable the Timeout Lock Mode .............................................................................. 9

10. How to determine the DT2000 version number................................................................. 10

11. Brute force hacking detection............................................................................................ 10

12. How to reset the DT2000 .................................................................................................. 11

13. How to configure the DT2000 with Windows OS .............................................................. 12

14. How to configure the DT2000 with Mac OS ...................................................................... 15!

Document No. 480ADT2000.A00

DT2000

Page 3 of 17

This user guide is for Kingston’s DataTraveler®2000 (referred to simply as DT2000 from this

point forward).

System Requirements

PC Platform

Supported PC Operating Systems

•Windows 10

•Windows 8/8.1

•Windows 7

•Windows Vista®SP2

Mac Platform

Supported Operating Systems

•Mac OS X 10.8.x - 10.11x

Linux Platform

Supported Operating Systems

•Linux v2.6 kernel+

Other Platforms Supported Operating System

___________________________________________________________________________

*Compatible devices only. Check with the manufacture of your device to see if it supports USB Flash drives.

•Chrome OS™, Android*

About This Guide

Document No. 480ADT2000.A00

DT2000

Page 4 of 17

Introduction

Thank you for purchasing the DataTraveler®2000, an ultra-secure and easy-to-use hardware-

encrypted USB 3.0 PIN-activated flash drive.

The DT2000 uses military-grade XTS-AES 256-bit hardware encryption, which encrypts all data

stored on the drive in real time. The DT2000 requires no software and is OS and host

independent.

The DT2000 incorporates a rechargeable battery that allows you to enter a 7-15 digit PIN

(Personal Identification Number) using the on-board keypad before connecting the drive to

a USB port.

Should the drive be lost or stolen, you can rest assured that all data held on the DT2000 is safe

and cannot be accessed by any unauthorised person.

The DT2000 unlocks using the on-board keypad and is not unlocked by a host computer. It is

not vulnerable to software/hardware-based key loggers or brute force attacks.

Note: The DT2000 rechargeable battery is not fully charged out of the box. We

recommend that you charge the battery prior to first use. To charge, plug the

DT2000 in to a powered USB port for 60 minutes to fully charge the battery.

Caution: The DT2000 is shipped with a default PIN of User PIN of

1-1-2-2-3-3-4-4

and, although it can be used straight out of the box with the default

PIN, for security reasons we highly recommend that you create a new

User PIN immediately by following the instructions under section 4 ‘How to

change User PIN’.

If you forget your PIN, all data will be inaccessible.

Document No. 480ADT2000.A00

DT2000

Page 5 of 17

1. DT2000 layout

2. LED indicators and their actions

LED

LED State

Description

LED State

Description

Red Black fade out

Locking down/incorrect PIN entry

Red and Green

blinking alternately

Factory

reset

Red blinking

Locked and awaiting factory default

PIN or defined PIN entry

Green solid

DT2000 is unlocked

Greenand Blue

blinking together

User option

mode

Green blinking

When connected to a USB port, if

Green LED blinks every 2 seconds

this indicates the DT2000 has been

set as ‘Read Only’

Blue solid

Connected to a USB port

Blue blinking

Data exchange with host/changing

User PIN

Document No. 480ADT2000.A00

DT2000

Page 6 of 17

3. How to use the DT2000 for the first time

The DT2000 is shipped with a default PIN of 11223344 and although it can be used straight out of the

box with the default PIN, for security reasons we highly recommend that you create a new User PIN

immediately by following the instructions under section 4 ‘How to change the User PIN’.

Follow the 3 simple steps in the table below to unlock the DT2000 with the default PIN.

Instructions (first time use)

LED

LED State

1. Press KEY button once

Red, Green & Blue LEDs will flash together once

and then the Red LED will continue to blink

2. Within 10 seconds, enter the User PIN

(default - 11223344) to unlock

the DT2000

Red LED will continue to blink

3. Press KEY button once

Red solid LED changes to Green solid LED

indicating successful default User PIN entry

4. How to change the User PIN

PIN requirements:

•Must be between 7-15 digits in length

•Must not contain only repetitive numbers, e.g. (3-3-3-3-3-3-3)

•Must not contain only consecutive numbers, e.g. (1-2-3-4-5-6-7), (7-8-9-0-1-2-3-4), (7-6-5-4-3-2-1)

Examples of these types of alphanumeric PINs are:

•For “password”, you would press the following keys:

7(pqrs) 2(abc) 7(pqrs) 7(pqrs) 9 (wxyz) 6(mno) 7(pqrs) 3(def)

•For “kingston”, you would press:

5(jkl) 4(ghi) 6(mno) 4(ghi) 7(pqrs) 8(tuv) 6(mno) 6(mno)

This method enables you to create long PINs that are easy to remember.

Instructions

LED

LED State

Note: Once the DT2000 has been successfully unlocked, the Green LED will remain on and

in a solid state for 30 seconds only, during which time the DT2000 needs to be connected to

a USB port. It can be locked down immediately by pressing and holding down the KEY button

for 3 seconds, or waiting for the 30 seconds to expire or by clicking the ‘Safely Remove

Hardware and Eject Media’ icon within your operating system.

Password tip: You can create a memorable word, name, phrase or any other alphanumeric

PIN combination simply by pressing the key with the corresponding letters on it.

Document No. 480ADT2000.A00

DT2000

Page 7 of 17

5. How to enable Options

Options Mode allows you to perform different functions, such as enabling or disabling the DT2000

as ‘Read-Only’, setting a ‘Timeout’ automatic lock and determining the version of the device.

The table below illustrates how to access the Options mode, sections 6 - 9 describe how to perform

the various functions.

1. Press KEY button once

Red, Green & Blue LEDs will flash together

once and then the Red LED will continue to

blink

2. Within 10 seconds, start to enter the User PIN

(default - 11223344) to unlock the DT2000

Red LED will continue to blink

3. Press KEY button once

Red solid LED changes to Green solid LED

indicating successful default User PIN entry

4. Press the KEY button twice

(double-click)

Blue LED blinks

5. Within 10 seconds, begin to enter

the new User PIN

Blue LED continues to blink

6. Press the KEY button twice

(double-click)

Green LED blinks

7. Within 10 seconds, begin to re-enter

the new User PIN

Green LED continues to blink

8. Press the KEY button twice

(double-click)

Red solid LED changes to Green solid LED,

indicating that the User PIN change was

successful

Note: If you make a mistake while defining a new User PIN or do not complete the

procedure, the drive will retain the old PIN.

The table below illustrates how to access the Options mode, sections 6

9 describe how to perform the

various functions.

Instructions

LED

LED State

1. Press KEY button once

Red, Green & Blue LEDs will flash together

once and then the Red LED will continue

to blink

2. Within 10 seconds, enter the User PIN

(default - 11223344) to unlock the

DT2000

Red LED will continue to blink

3. Press KEY button once

Red solid LED changes to Green solid LED

indicating successful User PIN entry

4. Press the KEY button 3 times

(triple-click)

Green and Blue LEDs blink together – awaiting

new instructions in OPTIONS Mode.

Document No. 480ADT2000.A00

DT2000

Page 8 of 17

6. How to enable Read-Only Mode

The DT2000 has a read-only mode that restricts write access to the drive. This is enabled by performing

the following steps.

Once activated, access is limited to read-only until write protect is disabled.

7. How to enable Read/Write Mode

Restricted write protect (read-only) access can be turned off with access restored to read/write.

This is enabled by performing the following steps.

Once activated, access is restored to the default read/write state.

Note: We have applied a naming convention to make it easy for you to remember the

keystrokes for each optional setting. In the table, above we have used numbers that represent

the ‘first letters’ of the optional feature name. For example, Read-Only = 7 (pqrs) 6 (mno).

Instructions

LED

LED Status

1. Unlock DT2000 with the User PIN

Red solid LED changes to Green solid LED

indicating successful User PIN entry

2. Enable Options by pressing the KEY button

3 times (triple-click)

Green and Blue LEDs blink together – awaiting new

instructions in OPTIONS Mode.

3. Within 10 seconds, begin to press number

7 (pqrs) followed by the number 6 (mno)

button (76)

Green and Blue LEDs continue to blink together

4. Press KEY button once

Blue LED quickly fades out to a solid Green - when

DT2000 is inserted into a USB port, the Green LED

blinks every two seconds indicating the drive is in

Read-Only Mode

Instructions

LED

LED Status

1. Unlock DT2000 with the User PIN

Red solid LED changes to Green solid LED

indicating successful User PIN entry

2. Enable Options by pressing the KEY button

3 times (triple-click)

Green and Blue LEDs blink together – awaiting

new instructions in OPTIONS Mode.

3. Within 10 seconds, enter the number 7

(pqrs) followed by the number 9(wxyz)

button (79)

Green and Blue LEDs continue to blink together

4. Press KEY button once

Blue LED quickly fades out to a solid Green -

when DT2000 is inserted into a USB port, the

Green LED blinks every two seconds indicating

the drive is in Read/Write Mode

Document No. 480ADT2000.A00

DT2000

Page 9 of 17

8. How to set the Timeout Lock Mode

To protect against unauthorised access when the DT2000 is connected to a host and

unattended, the DT2000 can be set to lock automatically after a pre-set amount of time.

In its default state, the DT2000 Timeout Lock feature is turned off. The Timeout Lock feature

can be set to activate (lock) anywhere between 1 and 99 minutes.

To set the Timeout Lock, follow steps in the table below.

9. How to disable the Timeout Lock Mode

To disable the Timeout Lock, follow steps in the table below.

Instructions

LED

LED Status

1. Unlock the DT2000 with the User PIN

Red solid LED changes to Green solid LED

indicating successful User PIN entry

2. Enable Options by pressing the KEY 3

times (triple-click)

Green and Blue LEDs blink together –

awaiting new instructions in OPTIONS

Mode

3. Within 10 seconds, enter the number 8(tuv)

followed by the number 5(jkl) button - (85)

Green and Blue LEDs continue to blink

together

4. Press KEY button once

Blinking Green LED

5. Within 10 seconds, enter the number 0

button twice (double-click) (zero zero) - (00)

Green LED continues to blink

6. Press the KEY button once

Green solid LED - Timeout Lock has been

disabled

Instructions

LED

LED Status

1. Unlock the DT2000 with the User PIN

Red solid LED changes to Green solid LED

indicating successful User PIN entry

2. Enable Options by pressing the KEY 3

button times (triple-click)

Green and Blue LEDs blink together –

awaiting new instructions in OPTIONS Mode

3. Within 10 seconds, enter the number 8

(tuv) followed by the number 5(jkl)

button - (85)

Green and Blue LEDs continue to blink

together

4. Press KEY button once

Blinking Green LED

5. Within 10 seconds, enter the length of

User Timeout in 2 digits:

00 = 0 minutes (default)

01 = 1 minute

99 = 99 minutes, etc.

Green LED continues to blink

6. Press the KEY button once

Green solid LED - Timeout Lock has been

enabled

Autres manuels pour DataTraveler 2000

Table des matières

Langues :

Autres manuels Kingston Technology Stockage

Kingston Technology

Kingston Technology DataTraveler SE9 Manuel utilisateur

Kingston Technology

Kingston Technology DataTraveler 2000 Manuel utilisateur

Kingston Technology

Kingston Technology Flash Memory Manuel utilisateur

Kingston Technology

Kingston Technology SH103S3 Manuel utilisateur

Kingston Technology

Kingston Technology MobileLite Wireless G2 Manuel utilisateur

Kingston Technology

Kingston Technology DataTraveler Locker+ Generation 3 DTLPG3 Manuel utilisateur

Kingston Technology

Kingston Technology DataTraveler 4000 Manuel utilisateur

Kingston Technology

Kingston Technology DT111 Manuel utilisateur

Kingston Technology

Kingston Technology DataTraveler Vault-Privacy Manuel utilisateur

Kingston Technology

Kingston Technology IRONKEY S1000B Manuel utilisateur

Kingston Technology

Kingston Technology DataTraveler 4000 G2 Manuel utilisateur

Kingston Technology

Kingston Technology DataTraveler Manuel utilisateur

Kingston Technology

Kingston Technology HyperX MAX 3.0 256GB Manuel utilisateur

Kingston Technology

Kingston Technology SDXC Manuel utilisateur

Kingston Technology

Kingston Technology CompactFlash Unltimate Manuel utilisateur

Kingston Technology

Kingston Technology KTM609 Manuel utilisateur

Kingston Technology

Kingston Technology IRONKEY D500SM Manuel utilisateur

Kingston Technology

Kingston Technology DataTraveler Locker+ G3 Manuel utilisateur

Kingston Technology

Kingston Technology IronKey Vault Privacy 80 Manuel utilisateur

Kingston Technology

Kingston Technology Ironkey D300 Manuel utilisateur

Kingston Technology

Kingston Technology IronKey 1000B Manuel utilisateur

Kingston Technology

Kingston Technology DataTraveler 4000 Manuel utilisateur

Kingston Technology

Kingston Technology DataTraveler 410 (DT410) Manuel utilisateur

Kingston Technology

Kingston Technology DataTraveler 2000 Manuel utilisateur

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur