Kilotech KRS SWP Series Manuel utilisateur

Kilotech

KRS SWP Series

Counter-top weighing scale

NTEP (USA) and Measurement Canada approved

www.kilotech.com

KILOTECH

KRS SWP series

Weighing Scale

NOTE: Le manuel en Français est disponible au

www.kilotech.com.

Thank you for purchasing a Kilotech Model KRS SWP

Weighing Scale. Please read all operating instructions

carefully before using the scale for the first time.

This scale is approved by the US and Canadian

governments and can be used in a “Legal for Trade”

application. If used in a “Legal for Trade” application, the

scale must be inspected and sealed as per the local

legislation.

Contents

1.0 Precaution before Using the Scale 3

1.1 Environment 3

1.2 Protection in the transportation 4

1.3 Leveling the scale 4

1.4 Turn on scale 4

2.0 Explanation of Display Symbols 5

3.0 Keypad Functions 6

4.0 Operations 6

5.0 Scale Parameters Setting 7

5.1 Backlight type 7

5.2 Auto shut. Off time 7

6.0 Power Supply 8

7.0 Error Message 9

1.0 Precaution before Using the Scale

1.1 Environment

The scale should always be used for its intended use (see

www.kilotech.com) and its intended capacity.

This scale is not protected against water; DO NOT spray with

liquids as this could damage the electronics or could cause serious

injury. To clean the scale, wipe it with a soft humid cloth and if

necessary, use a non-abrasive household cleaner.

The scale should always be used in an environment, which is free

from excessive air currents, corrosives, vibration, and temperature

or humidity extremes. These factors will affect displayed weight

reading.

DO NOT install the scale:

!Next to open windows or doors causing drafts or rapid

temperature changes.

!Near air conditioning or heating vents.

!Near vibrating, rotating or reciprocating equipment.

!Near magnetic fields or equipment that generates magnetic

fields.

!On an unstable work surface

!In a dusty environment

!In direct sunlight.

1.2 Protection in the transportation

Before the initial use, please refer to the following drawing to take

off the protection screw. When packing the scale for transportation,

install the protection screw on the scale in order to avoid any

damage to sensitive components.

1.3 Leveling the Scale

The scale is equipped with a level indicator on the left bottom side

of the front panel and four adjustable leveling feet. Adjust the

leveling feet until the bubble appears in the center circle of the

indicator. Then lock the feet in place using the lock nuts. Repeat

this procedure each time the scale is moved to a new location.

1.4 Turn on Scale

Do not turn on scale with anything on the platform. The switch is

located on the right side of the scale. The scale will start to count

down from nine to zero and will display the max capacity of the

scale in the display. The scale is then ready for use.

Allow the scale15-30 minutes to warm up prior to use.

2.0 Explanation of Display Symbols

LCD Display

Meaning of the Symbols

(Zero): Scale is in ZERO mode.

NET: Scale is in TARE mode.

: Low Voltage

(Stable): Scale is in stable mode.

kg/ lb: Indicates the current measuring units in weighing mode.

3.0 Keypad Functions

Button

Function

Zero/Enter

Zero the scale

Accepts the current setting on the display.

Move the settings backward in CAL parameter

settings

Move the settings forward in CAL parameter

settings

Select the options in settings

4.0 Operations

Turn on the scale; the scale will be in the weighing mode.

Zero Function

If the zero shifts during operation, press the “ZERO/ENTER” key to

set it to zero.

The Zero function is only active over a ±2%. Of capacity range.

EXAMPLE: If you are using a KRS-SWP3 (3kg) scale, 2% x 3kg =

60g. If the scale is NOT in TARE mode AND platter is empty BUT

the scale indicator reads between -60g and +60g, press the

ZERO/ENTER key to reset the scale to zero.

5.0 Scale Parameters Setting

Press and ZERO/ENTER key at the same time in weighing or

counting mode to enter into parameters setting.

5.1 Backlight type

Press or to set the backlight type to be “bl. 1”,“bl. 2”or “bl. 3”.

Please refer to the following.

Backlight type

Description

bl. 1

Automatic backlight

bl. 2

Backlight is always on

bl.3

Backlight is off

Press ZERO/ENTER key to confirm and return to next setting.

5.2 Auto Shut. off time

Press or to set the auto shut. off time to be 0, 2, 5 or 8.

Auto shut.

off time

Description

A.OFF 0

The auto shut. off function is unavailable

A.OFF 2

The scale will shut off automatically in 2 minutes

A.OFF 5

The scale will shut off automatically in 5 minutes

A.OFF 8

The scale will shut off automatically in 8 minutes

Note: The auto off has been set to 0 on the KRS-SWP.

The scale will shut off automatically only when the scale is

unloaded and without any key being pressed.

Press ZERO/ENTER key to confirm and exit from the parameter

setting mode.

6.0 Power Supply & Battery Operation

POWER SUPPLY

●DC 12V/1A

7.0 Error message

During the initial power-on testing it is possible the scale may show

error message.

The meaning of the error messages is described below.

Error

codes

Possible causes

Remedy

EPROM data lose.

Recalibrate the scale.

The initial zero is

outside the range of the

factory setting for zero.

1. Check if there is

something on the pan

or something touches

the top body when

switch on the scale,

move the load and

switch on again.

2. Recalibrate the scale.

--OL--

Load exceeds scale

capacity.

Reduce the load on the

pan.

------

System is busy.

Just wait.

LOBAT

OFF

Low voltage

Change adaptor.

If the error message is still displayed after above solutions have

been tried, contact your dealer for further support.

If scale is misused or received in impact etc., re-calibration may be

required. This should be done by a specialized scale professional.

If your distributor is an industrial scale dealer, he will be able to do

this for you. If you do not know who to contact, call the Kilotech

customer service desk at 800-694-4445 (Canada) or 877-328-5988

(USA) and we will recommend someone.

8.0 Calibration Procedure

Switch on the scale. And press the Calibration key at the bottom of

the case during self-testing period. The display will show as below:

CAL

Press ENTER key to set the Capacity and Resolution, and then

start weight loading procedure;

Capacity

The display shows as below:

Table des matières

Autres manuels Kilotech Échelle

Kilotech

Kilotech KWD 15K Manuel utilisateur

Kilotech

Kilotech KWS 2200 Manuel utilisateur

Kilotech

Kilotech CTR Series Manuel utilisateur

Kilotech

Kilotech Abacus AB30 Manuel utilisateur

Kilotech

Kilotech KPS 60 SS Manuel d'utilisation et d'entretien

Kilotech

Kilotech KWD 750SS Manuel utilisateur

Kilotech

Kilotech KPC 1500SS Manuel utilisateur

Kilotech

Kilotech KHA Series Manuel utilisateur

Kilotech

Kilotech KPC 1000SS Manuel d'utilisation et d'entretien

Kilotech

Kilotech KRS 3000 Manuel utilisateur

Kilotech

Kilotech KHS 200-30 Manuel utilisateur

Kilotech

Kilotech KPS MS Manuel utilisateur

Kilotech

Kilotech KPC 160 Manuel utilisateur

Kilotech

Kilotech KPC 2000-03A Manuel d'instructions

Kilotech

Kilotech KPOS 1530 Manuel utilisateur

Kilotech

Kilotech KPC-2000 Manuel utilisateur

Kilotech

Kilotech KPC 1500 SS Manuel utilisateur

Kilotech

Kilotech MS-4202L Adult Manuel utilisateur

Kilotech

Kilotech Integrator LE.3k Manuel utilisateur

Kilotech

Kilotech KPOS 1530 Manuel utilisateur

Kilotech

Kilotech Integrator LE.3k Manuel utilisateur

Kilotech

Kilotech KPS 60 Manuel utilisateur

Kilotech

Kilotech S-2000 Manuel utilisateur

Kilotech

Kilotech KPC 5000 Manuel d'instructions

Manuels Échelle populaires d'autres marques

AWS

AWS ZEO-50 Manuel utilisateur

Gima

Gima Glass Body Fat Analyzer Manuel de la liste des pièces

Seca

Seca 374 Manuel utilisateur

TEC

TEC TEC SL59 SERIES Manuel utilisateur

Axis

Axis B/E Series Manuel utilisateur

Alecto

Alecto ACW-40 Manuel utilisateur

Rice Lake

Rice Lake MSI-4260 IS Manuel utilisateur

IKA

IKA RCT basic safety control Manuel utilisateur

ADE

ADE M20011 Manuel utilisateur

Duronic

Duronic KS3000 Manuel utilisateur

Digi

Digi SM-720 Manuel utilisateur

Cardinal

Cardinal CS Series Manuel utilisateur

Korona

Korona Kastella Manuel utilisateur

A&D

A&D FC-50Ki Manuel utilisateur

BDA

BDA CAMARGUE Manuel utilisateur

Tanita

Tanita HD-357 Manuel utilisateur

Leifheit

Leifheit 03173 Manuel utilisateur

Lumme

Lumme LU-1340 Manuel utilisateur