Kidde K5CO Instructions d'utilisation

User and Installer Guide

Battery Carbon Monoxide Alarms

Quick Start Instructions

included at the back of

this User Guide

BS EN 50291-1:2018

LICENSE NO. KM 738897

Alarm Operate Fault

Move to Fresh Air

Carbon Monoxide Alarm

PPM of CO displayed

Lb= Low Battery

End= End of Unit Life

MODEL: K5DCO

Alarm

Move to

Fresh Air

Operate Fault

Carbon M onox ide Al arm

Model: K5CO

Model: K5DCO

P/N: K5CO-7201-01

MODEL: K5DCO

Thank You for Purchasing this Kidde Alarm

function to temporarily silence nuisance alarms.

Teach children how to respond to the alarm and that they should never play with the unit. This alarm is

designed to detect carbon monoxide from any source of combustion in a residential environment. It is not

designed for use in caravans, motor homes or boats.

NOTE: Please thoroughly read this user guide and save the document for future reference and to pass on

to any subsequent owner.

IMPORTANT: Additional markings can be found on the back of the unit.

The manufacturer recommends replacing this alarm ten years from the install date on the side of alarm.

Model: ______________________________

Date Code (on side): ____________________

Date of Purchase: ______________________

Where Purchased: ______________________

Date to Replace: ________________________

Product Support: 0800 917 0722

Please write down the below information

and have this at hand when you call.

ENVIRONMENTAL PROTECTION

Waste electrical products should not be disposed of with household

waste. Please recycle where facilities exist. Check with Local Authority

or Supplier for recycling advice.

Model: ______________________________

Date Code (on side): ____________________

Date of Purchase: ______________________

Where Purchased: ______________________

Date to Replace: ________________________

Contents

1. Carbon Monoxide Alarm: What To Do When the Alarm Sounds.................................................................................... 4

2. Other Alarm Visual and Audible Indicators.................................................................................................................................... 5

3. Troubleshooting Guide.............................................................................................................................................................................. 6

4. Introduction, Product Features and Specifications.................................................................................................................. 7

5. Limitations of CO Alarms........................................................................................................................................................................ 9

6. Recommended Locations for Alarms..............................................................................................................................................10

7. Locations to Avoid.......................................................................................................................................................................................11

8. Installation.........................................................................................................................................................................................................12

9. Operation and Testing............................................................................................................................................................................. 13

10. Recognizing Nuisance Alarms............................................................................................................................................................. 14

11. Battery ................................................................................................................................................................................................................ 15

12. General Carbon Monoxide (CO) Information............................................................................................................................. 16

13. Cleaning Your Alarm.................................................................................................................................................................................. 18

14. Service and Warranty................................................................................................................................................................................. 19

Quick Start Instructions .......................................................................................................................................................................... 20

1. Carbon Monoxide Alarm: What To Do When the Alarm Sounds

The carbon monoxide (CO) alarm pattern is four quick beeps repeating every 5 seconds. The red LED blinks in sync

with the beep pattern. The digital display on model K5DCO will show the PPM level of CO detected.

WARNING: CARBON MONOXIDE ALARM ACTIVATION INDICATES THE PRESENCE OF CARBON

MONOXI O AT HIGH CONCENTRATIONS WHICH CAN KILL YOU.

Based on recommendations from EN 50292, follow these steps if alarm sounds:

1. Keep calm and open all doors and windows. Turn off all fuel-burning appliances if possible. Note: it is possible

that outdoor conditions could influence domestic CO alarms (bad traffic pollution in cold weather, for

example). In these circumstances, the level of indoor CO might actually increase when doors and windows

are opened.

2. If the alarm continues to sound, even after being reset (where appropriate), then evacuate the premises,

alerting other occupants to the risk. Leave doors and windows open. Do not re-enter the premises.

3. Get medical help for anyone suffering the effects of CO poisoning, and advise that CO inhalation is suspected.

4. Call Gas Emergency Services: 0800 111 999, or your local Gas Safe Registered Engineer:

PHONE NUMBER:

Never restart the source of the CO problem until it has been corrected.

Never ignore the sound of the alarm!

NOTE: See Section RECOGNIZING NUISANCE ALARMS, for nuisance alarm situations.

2. Other Alarm Visual and Audible Indicators

Operational Mode Visual Indications Audible Indications Action/Note:

Normal (standby) Green LED blinks approx every

30 sec.

Test (button press when

no alarm condition is

present) Red LED blinks in sync with beep

pattern.

Green and amber LEDs illuminate.

Model K5DCO digital display will

show 3 dashes and then “888”.

4 loud pulses, a pause,

4 loud pulses.

Single beep

Perform test button press

once a week to verify proper

alarm operation.

CO Alarm Memory (unit

has experienced a CO

alarm event or 100 ppm

or more CO within the

last 14 days)

Red LED blinks every 60 sec. None. Model K5CO: Push button to

clear Alarm Memory.

Model K5DCO: Push Test/

Reset while the Peak Level

button is depressed to clear

Alarm Memory.

Peak Level CO

K5DCO only

Digital display shows the highest

CO reading between 11 and 999

ppm since the peak level was

reset.*

None. Push test/reset button while

peak level button is depressed

to clear peak level memory.

CO alarm reset Red LED continues to signal the

alarm pattern.

After button push: CO

alarm pattern stops. present or if it experienced a

nuisance situation. Re-alarm

means danger. Move to fresh

air and call 0800 111 999.

* NOTE: CO levels up to 30ppm can occur under normal non-dangerous conditions. Such conditions could include

3. Troubleshooting Guide

NOTE: If at any time your alarm fails to operate correctly (erratic or low sound, for example), or if you require further

information, please contact customer support at 0800 917 0722.

Trouble Condition Visual Indications Audible Indications Action:

Low Battery Amber LED blinks every

60 sec.

Model K5DCO digital

display will show “Lb”.

Chirp every 60 sec. * Push test button once to silence for 24 hrs.

Note: 30 days after Low Battery begins, the

* Replace batteries as soon as possible.

Fault Mode Amber LED blinks every

30 sec.

Model K5DCO digital

display will show “Err”.

Chirp every 30 sec. * See Cleaning Your Alarm section.

* Push test button once to attempt to reset

the unit.

End of Unit Life Amber LED blinks twice

every 60 sec.

Model K5DCO digital

display will show “End”.

Two chirps every

60 sec.

* Push button once to silence for 24 hrs.

Note: 30 days after End of Unit Life begins, the

* Remove, dispose unit, and replace as soon

as possible.

MCU FailureNone. Constant tone. * Replace alarm.

Stuck Button Amber LED blinks

every 5 sec.

Chirp every 5 sec. * Push button to dislodge it from being stuck.

If button cannot be unstuck, remove, dispose

unit, and replace as soon as possible.

3. Troubleshooting Guide

4. Introduction, Product Features and Specifications

Introduction

This alarm detects carbon monoxide using an electrochemical cell. Many times throughout this User Guide,

we will refer to Carbon Monoxide as “CO.”

Ten (10) years after the unit was installed, this unit will automatically alert you that it is time to replace the unit.

This is called “End of Unit Life” mode. See Troubleshooting Guide. To help track the life of your alarm, write the

installation date in the space provided on the side of the alarm. A label has been provided that has important

information on what to do in case of a CO alarm. Place the label at eye level on a wall near the alarm after it is

mounted.

Product Features and Specifications:

Temperature Operating Range: -10°C to 45°C

Humidity Operating Range: up to 90% RH non-condensing

Audible Alarm: 85+ dB(A) at 3 m, 3.0 to 3.5 kHz pulsing alarm

Digital Display (K5DCO only)

NOTE: Depending on the ambient condition (temperature, humidity) and the condition of the sensor,

the display readings may vary. The digital readings tolerances are 0-999 ± 30% +15ppm during these

conditions: Ambient: 27°C ± 12°C (80°F ± 10°F), atmospheric pressure ±10%, 40% ± 3% relative humidity

CO Sensor: Electrochemical

Peak Level Memory (K5DCO only)

CO Alarm Reset

Storage and Transport Conditions: -20° C to +60° C, 5-95%RH (non-condensing)

Product Features

Gr een,

Pow er LED

Red,

Ala rm LED

Test / Reset

Button

Model: K5CO

Alarm

Move to

Fresh Air

Operate Fault

Carbon Monoxide Alarm

Alarm Operate Fault

Move to Fresh Air

Carbon Monoxide Alarm

PPM of CO displayed

Lb= Low Battery

End= End of Unit Life

Gr e

Amber,

Fault LED

Amber,

Fault LED

en,

Pow er LED

Red,

Ala rm LED

Test / Reset

Button

Peak Level Button

Digital Display

with digital display

Model: K5DCO

5. Limitations of CO Alarms

WARNING: PLEASE READ CAREFULLY AND THOROUGHLY

This alarm is not intended to alert hearing impaired individuals.

LIMITATIONS OF CO ALARMS

IMPORTANT: This alarm is designed to detect carbon monoxide gas from ANY source of combustion. It is

NOT designed to detect any other gas. This alarm has not been tested specifically for use in caravans or

boats. Only CO alarms certified to EN50291-2 are fully approved for this purpose.

CAUTION: This alarm will only indicate the presence of carbon monoxide gas at the sensor. Carbon

monoxide gas may be present in other areas. Never restart the source of a CO problem until it has been

fixed. NEVER IGNORE THE ALARM!

WARNING: THIS PRODUCT IS INTENDED FOR USE IN ORDINARY INDOOR LOCATIONS OF

FAMILY LIVING UNITS. IT IS NOT DESIGNED TO MEASURE COMPLIANCE WITH COMMERCIAL

AND INDUSTRIAL STANDARDS. THIS ALARM IS NOT SUITABLE FOR INSTALLATION IN HAZARD

OUS LOCATIONS.

IMPORTANT: THIS CARBON MONOXIDE ALARM IS DESIGNED TO DETECT CARBON MONOXIDE

FROM ANY SOURCE OF COMBUSTION INCLUDING IMPROPER OR MALFUNCTIONING APPLIANC

ES. THE INSTALLATION OF THIS DEVICE SHOULD NOT BE USED AS A SUBSTITUTE FOR PROPER

INSTALLATION, USE AND MAINTENANCE OF FUEL BURNING APPLIANCES INCLUDING APPRO

PRIATE VENTILATION AND EXHAUST SYSTEMS.

This alarm does not prevent CO from occurring, nor can it solve any existing CO problem.

WARNING: THIS DEVICE IS DESIGNED TO PROTECT INDIVIDUALS FROM ACUTE EFFECTS OF

CARBON MONOXIDE EXPOSURE. IT MAY NOT FULLY SAFEGUARD INDIVIDUALS WITH SPECIFIC

MEDICAL CONDITIONS. IF IN DOUBT, CONSULT A MEDICAL PRACTITIONER. INDIVIDUALS WITH

MEDICAL PROBLEMS MAY CONSIDER USING WARNING DEVICES WHICH PROVIDE AUDIBLE AND

VISUAL SIGNALS FOR CARBON MONOXIDE CONCENTRATIONS UNDER 30 PPM.

This alarm has not been investigated for carbon monoxide detection below 50 PPM.

This alarm requires a continuous supply of electrical power – it will not work without power.

WARNING: THIS CARBON MONOXIDE ALARM IS NOT A SUBSTITUTE FOR INSTALLING AND

MAINTAINING AN APPROPRIATE NUMBER OF SMOKE ALARMS IN YOUR HOME. THIS ALARM

WILL NOT SENSE SMOKE, FIRE, OR ANY POISONOUS GAS OTHER THAN CARBON MONOXIDE.

FOR THIS REASON YOU MUST INSTALL SMOKE ALARMS TO PROVIDE EARLY WARNING OF FIRE

AND TO PROTECT YOU AND YOUR FAMILY FROM FIRE AND ITS RELATED HAZARDS.

6. Recommended Locations for CO Alarms

Note: CO alarms should be installed following the guidance of relevant local standards, such as

EN 50292.

Whether the alarm is wall-mounted or ceiling mounted, place the alarm a horizontal distance of between

1 metre and 3 metres from a fuel burning appliance.

When mounting the alarm on the wall, use an inside wall with the top edge of the alarm at a minimum

of 150 mm below the ceiling. The bottom of the alarm should also be at a level greater than the height

of any door or window.

Locate within hearing distance of bedrooms* and place at sleeping height if a heating appliance is in the

bedroom.

CO alarms in rooms with sloped ceilings should be located on the high side of the room.

Ceiling mounted alarms should be at least 300 mm from any wall.

If there is a partition in the room, locate the alarm on the same side of the partition as the potential source.

* A CO alarm should be installed in all rooms containing a fuel burning appliance. Additional CO alarms

should be installed in rooms where most awake time is spent, in every sleeping area, and on every level of

the home.

Autres manuels pour K5CO

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Kidde Système de sécurité

Kidde

Kidde KN-COB-IC-CA Manuel d'instructions

Kidde

Kidde KN-COB-DP2CA Manuel utilisateur

Kidde

Kidde 7CO Manuel utilisateur

Kidde

Kidde Slick 1SF23/9HI Instructions de montage

Kidde

Kidde KN-COP-DP-B Manuel utilisateur

Kidde

Kidde P4010ACSCO-WF Manuel utilisateur

Kidde

Kidde 123I Instructions de montage

Kidde

Kidde KN-COB-DP-H) Manuel utilisateur

Kidde

Kidde 8LLCO Manuel utilisateur

Kidde

Kidde KN-COPE-D Manuel utilisateur

Kidde

Kidde KN-COB-LP2 Manuel utilisateur

Kidde

Kidde KN-COB-IC Manuel utilisateur

Kidde

Kidde SLED177iCA Manuel utilisateur

Kidde

Kidde KN-COB-IC Manuel utilisateur

Kidde

Kidde ZP885 Instructions de montage

Kidde

Kidde KN-COPP-B-LS Manuel utilisateur

Kidde

Kidde KN-COP-DP-10YB Manuel utilisateur

Kidde

Kidde SLICK RF-SFTP Manuel utilisateur

Kidde

Kidde KN-COP-DP-10YL-AQ-WF Manuel utilisateur

Kidde

Kidde DM3000 Instructions de montage

Kidde

Kidde P4010ACSCOAQ-WF Manuel utilisateur

Kidde

Kidde KN-COEG-3 (900-01 13) Manuel utilisateur

Kidde

Kidde KN-COP-DP-10YL-AQ-WF Manuel utilisateur

Kidde

Kidde KN-COP-DP-10YH Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur