Kichler Lighting 35156 Manuel utilisateur
Français p. 17
Español p. 33
ITEM #0803773
MODEL #35156
CEILING FAN
1
ATTACH YOUR RECEIPT HERE
Serial Number Purchase Date
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-554-6504, 8 a.m. - 4:30 p.m, EST, Monday - Friday.
Kichler® is a registered trademark of
The L.D. Kichler Co. All Rights Reserved.
PACKAGE CONTENTS
2
A
Hanging Bracket
Down Rod
Canopy
Blade
Motor Coupling Cover
B
C
D
E
1
1
1
5
1
PART DESCRIPTION QTY
Motor Assembly
Light Kit Housing
Light Kit
Blade Iron
LED Bulb
G
F
H
I
J
1
1
1
5
3
PART DESCRIPTION QTY
A
F
C
H
E
BG
J
I
D
HARDWARE CONTENTS
3
SAFETY INFORMATION
Hanging bracket Screw
Hanging bracket Washer
Wire Connector
Blade Screw
HARDWARE BAG REMOTE CONTROL
Remote Control and Receiver
Remote Control Holder
Battery
Anchor and Screws
Wood Screw
Lag Screw
Blade Iron Screws
Shade Screws
Flat Washer + Spring Washer
Please read and understand this entire manual before attempting to assemble, operate or install the
product. Save this manual when finished.
WARNING:
• Important: When using an existing outlet box, be sure the box is securely attached to the building
structure and can support the full weight of the fan. Failure to do so can result in serious injury or
death.
• Turn off circuit breakers and wall switch to the fan supply wire leads. Warning: Failure to
disconnect power supply prior to installation may result in serious injury or death.
• Warning - Connecting this fan to a light switch (on/off) has been known to cause damage to the
receiver. This fan must be wired to continually receive power. Failure to do so will drastically
reduce the lifespan of this fan.
• Do not install fan on a ceiling with a pitch greater than 20°.
• WARNING – To Reduce The Risk Of Fire, Electric Shock, Or Personal Injury, Mount To Outlet Box
Marked 'Acceptable for Fan Support of 15.9 kg (35 lbs) or less' And Use Mounting Screws
Provided With The Outlet Box and/or Support Directly From Building Structure. Most Outlet Boxes
Commonly Used For The Support of Luminaires Are Not Acceptable For Fan Support And May
Need To Be Replaced. Consult A Qualified Electrician If In Doubt."
• Important: Be sure wiring box is properly grounded or that a ground (green) wire is present.
• Make sure the installation site you choose allows a minimum of 7 feet from the floor to the end of
the blades.
Balance Kit
WARNING (continued)
CAUTION:
PREPARATION
4
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and diagram. If any part is missing or damaged, do not attempt to assemble the product.
Contact customer service for replacement parts.
Estimated assembly time: 30 minutes to 1 hour.
Tools Required for Assembly (not included): Phillips screwdriver, flathead screwdriver, wire strippers,
electrical tape, ladder, safety glasses.
A B C
ASSEMBLY INSTRUCTIONS
• WARNING-To reduce risk of fire, electric shock, or personal injury, mount to outlet box marked
“Acceptable for Fan Support of 15.9kg (35lbs) or less” and use mounting screws provided with the
outlet box and/or support directly from building structure. Most outlet boxes commonly used for
the support of luminaries are not acceptable for fan support and may need to be replaced.
Consult a qualified electrician if in doubt.
• Warning-Risk of fire, electric shock, or personal injury. Ceiling fans may be either directly
supported from a structural framing member of a building and (see examples in figures A & B) or
may be mounted to an outlet box marked acceptable for fan support of 31.8 kg (70 lbs) to 15.9kg
(35 lbs) (see example in figure C).
• To reduce the risk of fire or electrical shock, do not use this fan with any solid state fan speed
device or variable speed control.
• Do not touch hot LED
• The LED light output is strong enough to injure human eyes. Precautions must be taken to
prevent looking directly at the LEDs with unaided eyes for more than a few seconds.
• Read and understand all instructions and illustrations completely before proceeding with assembly
and installation of this fixture.
• If you have any doubts about how to install this lighting fixture, or if the fixture fails to operate
completely, please contact a qualified licensed electrical contractor.
• All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts
out, or use any parts that are worn out or broken. Failure to obey this instruction could invalidate
the UL listing, C.S.A. certification, and/or UL listing of this fixture.
• This fixture is intended for installation in accordance with the National Electric Code (NEC) and all
local code specifications.
• Use ONLY the supplied LED driver to power fixture.
• Driver cable is not intended for use through or concealed behind walls, floors, or ceilings.
ASSEMBLY INSTRUCTIONS
5
1.
Turn off the circuit breaker to the fan supply line
leads.
DANGER: Failure to disconnect power supply prior
to installation may result in serious injury or death.
3. Loosen the set screws found on the coupling on top
of the motor assembly (F). Then, remove the
preassembled hair and clevis pin and save for later
use.
2. Secure the hanging bracket (A) to the ceiling outlet
box using hanging bracket screws and hanging
bracket washers.
Important: If attaching the fan to a sloped ceiling,
make sure open end of mounting bracket is installed
facing the roof. Do not install fan on a ceiling with a
pitch greater than 20°.
2
A
Outlet Box
Hanging
Bracket
Washer
Hanging
Bracket
Screw
3
F
Clevis Pin
Hair Pin
20 20
OFF
OFF OFF
100
1
6
ASSEMBLY INSTRUCTIONS
4. Insert downrod (B) through canopy (C) and motor
coupling cover (E).
5. Feed wires from the motor assembly (F) through the
downrod (B), then insert the downrod (B) into the
coupling found on top of the motor assembly (F).
4a
4b
B
B
C
C
E
5
B
F
Motor
Coupling
7
ASSEMBLY INSTRUCTIONS
6. Pass the previously removed clevis pin through the
downrod (B) and coupling of motor assembly (F),
then secure with previously removed hair pin.
Re-tighten set screws on the coupling and lower the
motor coupling cover (E).
7. Carefully lift the fan and seat the ball of the downrod
(B) in the hanger bracket (A). Be sure the groove in
the ball is lined up with the tab on the hanger bracket
(A).
DANGER: Be careful when aligning the tab to
the groove in ball. If not fully engaged, there is a
possibility of the fan falling, which may result in
serious injury or death.
7
A
B
6
B
E
F
ASSEMBLY INSTRUCTIONS
8
8. For Canadian installation and for USA fans over 35
lbs, the safety cable must be installed into the house
structure beams using a 3” lag screw. Make sure
that when the safety cable is fully extended the lead
wires are longer than the cable and no stress is
placed on the lead wires.
Safety
Cable
Lag
Screw
Safety
Cable
Flat
Washer
Spring
Washer
8
Safety
Cable
9
REMOTE CONTROL
RECEIVER
9. In order to use this remote control the dip switches
must match on both the remote control and the
receiver. Make sure they both have the same
configuration.
Remove the battery cover from the remote control.
Slide dip switches up or down using a small screw
driver (not included). Then match the dip switches
on the receiver to the same position as the remote
control.
Install the battery (included) and replace the battery
cover you previously removed.
ASSEMBLY INSTRUCTIONS
9
10.Wiring the fan per wiring diagram and securely connect wires with wire connectors: Wrap
electrical tape (not included) around each wire connector and make sure no bare wire or wire
strands are visible after making connections.
• Connect WHITE wire from the fan to WHITE wire marked TO MOTOR N from the receiver.
• Connect BLUE wire from the fan to BLUE wire marked FOR LIGHT from the receiver.
• Connect BLACK wire from the fan to BLACK wire marked TO MOTOR L from the receiver.
• Connect BLACK wire from the outlet box to BLACK wire marked AC IN L from the receiver.
• Connect WHITE wire from the outlet box to WHITE wire marked AC IN N from the receiver.
• Connect GROUND (GREEN) wires from hanger bracket and downrod ball, to GROUND (GREEN
or BARE COPPER) from house.
GREEN or
GREEN
BARE COPPER
Receiver
BLUE (Light)
BLACK (Motor)
WHITE (Neutral)
BLUE
BLACK
WHITE
10
WHITE
(Neutral) BLACK
(Live)
WHITE
(AC Input)
BLACK
(AC Input)
Outlet Box
ASSEMBLY INSTRUCTIONS
10
11.Once wiring step has been completed, slide the
wired remote receiver in between the hanging
bracket (A) and the top of the downrod ball (B) with
the flat side of the receiver facing the ceiling. Turn
lead wires upward and carefully push them into the
outlet box, with the white and green wires to one
side of the box and the black wires toward the other
side.
12.Loosen one of the shoulder screws without fully
removing it from the hanging bracket (A).
Completely remove the remaining shoulder screw
from the hanging bracket (A).
Assemble canopy (C) by rotating keyhole slot on
canopy (C) over shoulder screw in hanging bracket
(A). Loosely screw the previously removed shoulder
screw into the canopy and onto hanging bracket (A).
Tighten shoulder screws. Securely attach and tighten
the canopy hole cover over the shoulder screws in
the hanging bracket (A) utilizing the keyhole slot
twist-lock feature.
11
A
B
13
I
D
Blade
Screw
13.Attach blade iron (I) to blade (D) with blade screws.
Do not fully tighten blade screws until each screw
has been started. Then, tighten each blade screw
starting with the center screw. Repeat for remaining
blade irons (I) and blades (D).
12
C
A
Shoulder
Screw
Canopy
Hole
Cover
Shoulder
Screw
Table des matières
Langues :
Autres manuels Kichler Lighting Ventilateur
Kichler Lighting
Kichler Lighting Saxon Premier Manuel utilisateur
Kichler Lighting
Kichler Lighting Cottage Grove Manuel utilisateur
Kichler Lighting
Kichler Lighting 300457 Manuel utilisateur
Kichler Lighting
Kichler Lighting Kittery Point Manuel utilisateur
Kichler Lighting
Kichler Lighting 35157 Manuel utilisateur
Kichler Lighting
Kichler Lighting 300044 Manuel utilisateur
Kichler Lighting
Kichler Lighting 310155 Manuel utilisateur
Kichler Lighting
Kichler Lighting Lija Manuel utilisateur
Kichler Lighting
Kichler Lighting sterling manor select Manuel utilisateur
Kichler Lighting
Kichler Lighting Grace 300316 Manuel utilisateur
Kichler Lighting
Kichler Lighting SPYRA Manuel utilisateur
Kichler Lighting
Kichler Lighting 52" Canfield Pro Manuel utilisateur
Kichler Lighting
Kichler Lighting KOSMUS Manuel utilisateur
Kichler Lighting
Kichler Lighting ERIS 337060 Manuel utilisateur
Kichler Lighting
Kichler Lighting Rana 310155 Manuel utilisateur
Kichler Lighting
Kichler Lighting Guardian 330057 Manuel utilisateur
Kichler Lighting
Kichler Lighting Golden Iridescence Manuel utilisateur
Kichler Lighting
Kichler Lighting Tide Weather+ Manuel utilisateur
Kichler Lighting
Kichler Lighting RIED Manuel utilisateur
Kichler Lighting
Kichler Lighting Sterling Manor Manuel utilisateur
