Keysight N9030A Manuel d'installation et d'exploitation
Notice: This document contains references to Agilent.
Please note that Agilent’s Test and Measurement busi-
ness has become Keysight Technologies. For more in-
formation, go to www.keysight.com.
Keysight N9030A Signal Analyzer
Option BBA
Analog Baseband IQ Inputs
Retrofit Kit
Installation Note
Part Number N9030-90045
Printed in USA August 2014
Notice.
The information contained in this document is subject to change without notice.
Keysight Technologies makes no warranty of any kind with regard to this material, including but not
limited to, the implied warranties of merchantability and fitness for a particular purpose. Keysight
Technologies shall not be liable for errors contained herein or for incidental orconsequential damages
inconnection with the furnishing, performance, or use of this material.
© Copyright 2011 - 2014 Keysight Technologies, Inc.
Installation Note N9030-90045 3
Option BBA, Analog Baseband I/Q Inputs Retrofit Kit
Option BBA, Analog Baseband I/Q Inputs Retrofit Kit
Products Affected: N9030A, PXA Signal Analyzer with Options 503,
508, 513, or 526
Serial Numbers: All
Option BBA
To Be Performed By: (X) Agilent Service Center
(X) Personnel Qualified by Agilent
( ) Customer
Estimated Installation Time:
Estimated Adjustment Time:
Estimated Verification Timea:
a. To ensure that this newly installed option is functioning properly, the procedure that follows includes
the requirement of performing certain adjustments and performance verification tests. However, the
completion of these tests does not guarantee that the instrument meets all advertised specifications.
Software and test equipment is required for making adjustments and for performance verification testing.
Information on how to obtain this software can be found at:
www.agilent.com/find/calibrationsoftware
While Agilent does recommend that a full calibration be performed after the installation of this upgrade,
the end user must ultimately determine whether they want this service or not. If a full calibration is
required, arrangements regarding the level of calibration must be made between the end user and the
calibration provider.
3.0 Hours
0.5 Hours
3.0 Hours
4Installation Note N9030-90045
Option BBA, Analog Baseband I/Q Inputs Retrofit Kit
Introduction
This kit provides all parts and instructions necessary to install Option BBA, Analog Baseband I/Q
Input, into the Agilent N9030A with frequency range 26.5 GHz and below.
NOTE
1. The signal analyzer requires software revision A.08.54 or newer.
This retrofit kit installation requires that you re-install instrument software even if the current
software meets the revision requirement above.
The latest revision of the PXA Signal Analyzer software may be downloaded from
http:/www.agilent.com/find/xseries_software.
The instrument software must be installed AFTER the hardware in the kit is installed. Follow the
procedure in this document for redeeming and installing the option upgrade license key.
2. The option is licensed for one instrument model/serial number combination. The license key will
only install on the designated instrument.
Installation Note N9030-90045 5
Option BBA, Analog Baseband I/Q Inputs Retrofit Kit
Installation Kit Parts List
Quantity Description Agilent Part Number
1 BBIQ Main Board N9020-65093
1 LED Board N9020-63095
1 BBIQ Interface Board N9020-65094
1 LED Board Overlay, Bottom N9020-80013
1 LED Board Overlay, Top N9020-80014
1 Cable, Flex Ribbon 8121-2090
1 Core Bracket N9020-00012
1 Cable, Small Coaxial 8121-1401
1 Cable, RF Switch 1 - Switch 2 N9020-20210
1 Display Bracket W1312-00115
60 Screws, M3 X 0.5 (8 mm long) 0515-0372
1 Vibration Mount 0460-2725
9 Screws, M3 X 0.5 (6 mm long) 0515-1227
9 Screws, M3 X 0.5 (8 mm long) 0515-1035
2 Screws, Hex Shoulder N9020-20017
2 Main Board Warning Labels N9020-80036
1 Entitlement Certificate 5964-5178
1 Entitlement Certificate Envelope 5967-7169
2 #1 Cable Label 7121-5601
2 #7 Cable Label 7121-5607
2 #0 Cable Label 7121-5610
5 Tie Wrap 1400-0249
1 Installation Note This note
1 Probe tip BNC adapter (send to end user) 5063-2143
1 Cable, BNC - BNC (send to end user) 8120-2682
6Installation Note N9030-90045
Option BBA, Analog Baseband I/Q Inputs Retrofit Kit
Tools Required
❏PXA Service Guide as N9030A-0BW or N9030-90030
❏T-10 Torx Driver
❏T-20 Torx Driver
❏5/16-inch torque wrench
❏1/4-inch open end wrench
❏1/4-inch socket on 4 lb torque wrench
❏scissors or knife
❏diagonal cutters
❏USB storage device with > 2 GB free memory
WARNING Before you disassemble the instrument, turn the power switch to Standby,
wait until the instrument has completely shut down, and unplug the
instrument. Failure to unplug the instrument can result in personal injury.
CAUTION Electrostatic discharge (ESD) can damage or destroy electronic components. All
work on electronic assemblies should be performed at a static-safe workstation.
Refer to the documentation that pertains to your instrument for information about
static-safe workstations and ordering static-safe accessories.
Agilent Service Center or Customer Calibration Lab:
The following kit items are not installed in the analyzer upgrade and need to be shipped back to the
end user for their use:
• USB storage device
• 5063-2143, Probe tip BNC adapter
• 8120-2682, cable
• Entitlement Certificate
Installation Note N9030-90045 7
Option BBA, Analog Baseband I/Q Inputs Retrofit Kit
Installation Procedure
CAUTION If the instrument is placed on its face during any of the following procedures, be
sure to use a soft surface or soft cloth to avoid damage to the front panel, keys, or
input connector.
NOTE Make sure any adapters on the front panel are removed.
Licensing the Option
Installation Procedure using USB Storage Device
1. Locate the Option Upgrade Entitlement Certificate from the kit.
2. Redeem the Option Upgrade Entitlement Certificate by following the instructions on the
Certificate.
3. After redeeming your Option Upgrade Entitlement Certificate you will receive an email with an
attached License File.
4. Locate a USB storage device. Perform a virus scan on this device before use.
5. Save the License File to the root directory of the USB Storage Device.
6. Assure the instrument is fully booted.
7. Connect the USB Storage Device to one of the USB ports. Windows will detect the new hardware
and may display the configuration menu shown in Figure 1. This menu may be configured
according to your preferences.
Figure 1 USB Storage Device Configuration Menu
8Installation Note N9030-90045
Option BBA, Analog Baseband I/Q Inputs Retrofit Kit
8. The instrument will automatically consume the License File (this may take a few minutes). When
the License File is consumed the Agilent License Manager will display a “Successful
License Installation” message as shown in Figure 2.
Figure 2 Successful License Installation
Alternate Installation Procedure
The License File can be manually installed over USB or LAN by placing the license file in the
following folder on the MXA C:\Program Files\Agilent\licensing.
Installation Note N9030-90045 9
Option BBA, Analog Baseband I/Q Inputs Retrofit Kit
Instrument Cover Removal
1. Power down the instrument and wait for the standby light to come on. Disconnect the instrument
from ac power.
2. Refer to Figure 3. Using the T-20 driver, remove the 4 screws (1) (two on each side) that attach
the strap handles (2) on each side of the instrument.
3. Remove the four key locks from the instrument four bottom feet.
4. Remove the four instrument bottom feet.
5. Using the T-20 driver, remove the four screws (including washers) (3) that hold the rear feet (4)
in place.
6. Pull the instrument cover (5) off towards the rear of the instrument.
Figure 3 Instrument Outer Case Removal
10 Installation Note N9030-90045
Option BBA, Analog Baseband I/Q Inputs Retrofit Kit
Front Frame Assembly Removal
1. Refer to Figure 4. Look at the upper right corner of the front panel. If EXT MIXER SMA
connector is present (Option EXM), locate the connection where the two semi-rigid cables mate
behind the front frame (2). Disconnect the connections using a 1/4-inch wrench and a 5/16-inch
wrench.
2. Using the T-10 driver, remove the eight screws (1), four on each side, to detach the front frame
from the chassis.
3. Refer to Figure 5. Pull the front frame carefully away from the chassis. Remove the ribbon cable
W1 from the A8 Motherboard.
NOTE W1 may have locking springs on each side. Depress the spring on each side of the
connector to remove from the motherboard.
Figure 4 Front Frame Removal
Autres manuels pour N9030A
1
Table des matières
Autres manuels Keysight Instrument de mesure
Keysight
Keysight N774 C Series Mode d'emploi
Keysight
Keysight A Series Manuel utilisateur
Keysight
Keysight N5227BU-420 Manuel utilisateur
Keysight
Keysight M9601A Guide de l'utilisateur
Keysight
Keysight NFA Series Manuel d'utilisation et d'entretien
Keysight
Keysight InfiniiMax III+ N7000 Manuel utilisateur
Keysight
Keysight N9912A Manuel utilisateur
Keysight
Keysight u2722a Manuel utilisateur
Keysight
Keysight E4417A Manuel utilisateur
Keysight
Keysight U1461A Manuel utilisateur
Keysight
Keysight U1211A Manuel utilisateur
Keysight
Keysight N5224AU-217 Manuel d'installation et d'exploitation
Keysight
Keysight U1583B Manuel utilisateur
Keysight
Keysight N9030B Manuel d'installation et d'exploitation
Keysight
Keysight N9010AK-MTU Manuel d'installation et d'exploitation
Keysight
Keysight PXA Series Manuel d'installation et d'exploitation
Keysight
Keysight N6854A Manuel utilisateur
Keysight
Keysight 16801A Manuel utilisateur
Keysight
Keysight N1911A Manuel utilisateur
Keysight
Keysight N2780B Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
ADTEK
ADTEK MW-5 Manuel utilisateur
Acterna
Acterna MS1400 Manuel utilisateur