Keysight Technologies U9361G Manuel utilisateur
Keysight Technologies
U9361C/F/G/M Receiver Calibrator
Quick Start
Guide
Notices
© Copyright 2020-2021 Keysight Technologies, Inc.
The information contained in this document is subject to change without notice.
Keysight Technologies makes no warranty of any kind with regard to this material, including but
not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Keysight Technologies shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of this material.
Manual Part Number
U9361-90001
Edition
Edition 1, October 2021
Supersedes: March 2021
Printed in USA
Published by:
Keysight Technologies, Inc.
1400 Fountaingrove Parkway
Santa Rosa, CA 95403
U9361C/F/G/M Receiver Calibrator Quick Start Guide 3
What You Will Find in this Document
What You Will Find in this Document
Where to Find the Latest Information....................................................................................4
ESD Information......................................................................................................................5
Protection from Electrostatic Discharge.....................................................................5
Handling of Electronic Components and ESD............................................................6
For Additional Information about ESD ........................................................................6
Overview..................................................................................................................................7
Keysight Products Supported...................................................................................... 7
Unpack, Inspect and Verify Box Contents.............................................................................7
Initial Inspection ........................................................................................................... 7
Shipping Problems .......................................................................................................8
Calibrators Covered by This Guide ........................................................................................9
Operation...............................................................................................................................11
Operating Precautions ...............................................................................................11
Warnings and Cautions..............................................................................................11
Instrument Information ..............................................................................................12
Environmental Conditions ...................................................................................12
Environmental Information..................................................................................12
Regulatory Information........................................................................................12
EMC Compliance..................................................................................................12
Regulatory Markings............................................................................................14
Setup Procedure.........................................................................................................16
LED Definition.............................................................................................................18
Example: RCal Calibration Using a UXA Signal Analyzer ........................................19
Care and Maintenance .........................................................................................................24
Connector Care...........................................................................................................24
Making Connections...................................................................................................26
Cleaning Connectors..................................................................................................33
Returning a U9361C/F/G/M Receiver Calibrator for Service.............................................34
4 U9361C/F/G/M Receiver Calibrator Quick Start Guide
Where to Find the Latest Information
Where to Find the Latest Information
Documentation is updated periodically. For the latest information about these products,
including instrument software upgrades, application information, and product information,
browse to one of the following URLs, according to the name of your product:
http://www.keysight.com/find/u9361c
http://www.keysight.com/find/u9361f
http://www.keysight.com/find/u9361g
http://www.keysight.com/find/u9361m
To receive the latest updates by email, subscribe to Keysight Email Updates at the following
URL:
https://support.keysight.com
Information on preventing instrument damage can be found at:
http://keysight.com/find/PreventingInstrumentRepair
Product specific information and support, software and documentation updates:
http://www.keysight.com/find/rcal
Is your product software up-to-date?
Periodically, Keysight releases software updates to fix known defects and incorporate product
enhancements. To search for software updates for your product, go to the Keysight Technical
Support website at:
http://www.keysight.com/find/techsupport
U9361C/F/G/M Receiver Calibrator Quick Start Guide 5
ESD Information
ESD Information
Protection from Electrostatic Discharge
Electrostatic discharge (ESD) can damage or destroy electronic components. All work on
electronic assemblies should be performed at a static-safe workstation. Figure 1 shows an
example of a static-safe workstation using two types of ESD protection:
— Conductive table-mat and wrist-strap combination.
— Conductive floor-mat and heel-strap combination.
Both types, when used together, provide a significant level of ESD protection. Of the two, only
the table-mat and wrist-strap combination provides adequate ESD protection when used alone.
To ensure user safety, the static-safe accessories must provide at least 1 megohm of isolation
from ground.
Figure 1 Example of a Static-Safe Workstation
These techniques for a static-safe workstation should not be used when
working on circuitry with a voltage potential greater than 500 volts.
6 U9361C/F/G/M Receiver Calibrator Quick Start Guide
ESD Information
Handling of Electronic Components and ESD
The possibility of unseen damage caused by ESD is present whenever components are
transported, stored, or used. The risk of ESD damage can be greatly reduced by paying close
attention to how all components are handled.
— Perform work on all components at a static-safe workstation.
— Keep static-generating materials at least one meter away from all components.
— Store or transport components in static-shielding containers.
For Additional Information about ESD
For more information about preventing ESD damage, contact the Electrical Over
Stress/Electrostatic Discharge (EOS/ESD) Association, Inc. The ESD standards developed by this
agency are sanctioned by the American National Standards Institute (ANSI).
Always handle printed circuit board assemblies by the edges. This will
reduce the possibility of ESD damage to components and prevent
contamination of exposed plating.
U9361C/F/G/M Receiver Calibrator Quick Start Guide 7
Overview
Overview
The Keysight U9361C/F/G/M Receiver Calibrator is a palm sized USB reference signal source
that is used to calibrate and improve the accuracy of products and systems for which the
U9361C/F/G/M is a Keysight-approved accessory.
With emphasis on ease-of-use, the embedded features of the calibrator will automatically
transfer calibration data from the calibrator memory to the signal analyzer through the USB
plug-and-play feature. The analyzer will also auto-detect the model, serial number, and options
present on the calibrator.
Keysight Products Supported
— N9020B1/21B MXA Signal Analyzer
— N9030B/32B PXA Signal Analyzer
— N9040B/41B/42B UXA Signal Analyzer
Unpack, Inspect and Verify Box Contents
Initial Inspection
Inspect the shipping container and the cushioning material for signs of stress. Retain the
shipping materials for future use, as you may wish to ship the instrument to another location or
to Keysight Technologies for service.
Figure 2 Shipping Case
1. Requires option DP2, MPB, or B40.
Top Level
Instrument
and wrench
Bottom Level
Cables
8 U9361C/F/G/M Receiver Calibrator Quick Start Guide
Unpack, Inspect and Verify Box Contents
To access the cables located on the bottom level, remove the top cushion that holds the
instrument and wrench by lifting up on the corner cutouts provided.
Shipping Problems
If the shipping materials are damaged or the contents of the container are incomplete:
— Contact the nearest Keysight Technologies office.
— Keep the shipping materials for the carrier’s inspection.
— If you must return the calibrator to Keysight Technologies, use the original (or comparable)
shipping materials. See “Returning a U9361C/F/G/M Receiver Calibrator for Service” on
page 34.
Table 1 Standard Shipped Items
Item Description
Startup Guide Provides instructions on usage, safety, troubleshooting, specifications, and general information.
Certificate of calibration Provides information regarding the instrument calibration.
Shipping Case Case-Plastic Rcal
Wrench Torque 8lb-in, 5/16 Inch (U9361F) or,
Torque Special Double-end 14mm-open end 4 and 10-in-lb (U9361M)
USB Cable Cable-Assembly USB 3.0 Type-A Plug to Type-C Plug, 1 meter long
Coaxial Cable Cable Assembly-Coaxial BNC Male to SMB-Female, 1 meter long
U9361C/F/G/M Receiver Calibrator Quick Start Guide 9
Calibrators Covered by This Guide
Calibrators Covered by This Guide
— U9361C: 10 MHz to 26.5 GHz Receiver Calibrator, 3.5 mm RF out connector
— U9361F: 10 MHz to 50 GHz Receiver Calibrator, 2.4 mm RF out connector
— U9361G: 10 MHz to 67 GHz Receiver Calibrator, 1.85 mm RF out connector
— U9361M: 10 MHz to 110 GHz Receiver Calibrator, 1.0 mm RF out connector
Figure 2 Calibrator Front View
10 U9361C/F/G/M Receiver Calibrator Quick Start Guide
Calibrators Covered by This Guide
Figure 3 Calibrator Rear View
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels Keysight Technologies Équipement de test
Keysight Technologies
Keysight Technologies InfiniiVision DSOX1204A Manuel
Keysight Technologies
Keysight Technologies i7090 Mode d'emploi
Keysight Technologies
Keysight Technologies U1610/20A Manuel utilisateur
Keysight Technologies
Keysight Technologies Infiniium 90000A Series Manuel utilisateur
Keysight Technologies
Keysight Technologies 81960A Manuel utilisateur
Keysight Technologies
Keysight Technologies Infiniium 90000A Series Manuel utilisateur
Keysight Technologies
Keysight Technologies N5511A Manuel utilisateur
Keysight Technologies
Keysight Technologies N7015A Manuel utilisateur
Keysight Technologies
Keysight Technologies 16380C Guide de démarrage rapide
Keysight Technologies
Keysight Technologies E5405A-Pro Series Manuel utilisateur
Keysight Technologies
Keysight Technologies U3042AE12 Manuel
Keysight Technologies
Keysight Technologies N4877A Manuel utilisateur
Keysight Technologies
Keysight Technologies InfiniVision 6000L Series Manuel utilisateur
Keysight Technologies
Keysight Technologies E6640A Manuel utilisateur
Keysight Technologies
Keysight Technologies X Series Manuel d'installation et d'exploitation
Keysight Technologies
Keysight Technologies 8490D Manuel de service
Keysight Technologies
Keysight Technologies B1542A Pulsed IV Package Manuel utilisateur
Keysight Technologies
Keysight Technologies InfiniiVision 2000 Manuel utilisateur
Keysight Technologies
Keysight Technologies D9020DDRC Manuel utilisateur
Keysight Technologies
Keysight Technologies U3047AM12 Manuel
Manuels Équipement de test populaires d'autres marques
SMART
SMART KANAAD SBT XTREME 3G Series Manuel utilisateur
Agilent Technologies
Agilent Technologies BERT Serial Manuel utilisateur
Agilent Technologies
Agilent Technologies N3280A Manuel utilisateur
Vernier
Vernier Go Direct Voltage Manuel utilisateur
Lifeloc
Lifeloc R.A.D.A.R. Manuel utilisateur
Fluke
Fluke T5-600 Instructions d'utilisation et d'installation
