Keysight Technologies N6700C Series Manuel utilisateur

Keysight Series N6700C

Low-Profile Modular

Power System

User's Guide

Sie haben Fragen oder wünschen eine Beratung? Angebotsanfrage unter 07121 / 51 50 50 oder über [email protected]

Distributed by:

Legal and Safety Information 7

Legal Notices 7

Safety Symbols 9

Safety Notices 10

1 Quick Reference 13

Introduction to the Instrument 14

Features at a Glance 14

Front Panel at a Glance 16

Rear Panel at a Glance 17

Front Panel Display at a Glance 18

Front Panel Keys at a Glance 20

Front Panel Menu Reference 21

Command Quick Reference 25

Models and Options 38

Model Descriptions 38

Model Differences 39

Options 42

Specifications 43

Supplemental Characteristics N6700C, N6701C, N6702C 43

Dimension Diagrams 45

2 Installation 47

Preliminary Information 48

Check for Items Supplied 48

Inspect the Unit 49

Review Safety Information 49

Observe Environmental Conditions 49

Installing the Mainframe 50

Module Installation 50

Rack Mounting 52

Bench Installation 53

Redundant Ground for 400 Hz Operation 53

Connecting the Power Cord 54

Connecting the Outputs 55

Output Wiring 55

Wire Sizing 56

Keysight N678xA SMU Wiring 58

Multiple Load Wiring 60

Positive and Negative Voltages 60

Load Capacitor Response Times 61

Ferrite Core Installation - for Keysight N6792A only 61

Protecting Sensitive Loads from AC Power Switching Transients 62

Remote Sense Connections 63

Wiring 63

Open Sense Leads 64

Over-Voltage Protection Considerations 64

Output Noise Considerations 64

3 Keysight N6700C Series User's Guide

Parallel and Series Connections 65

Parallel Connections 65

Series Connections 67

Auxiliary Measurement Connections 70

Interface Connections 71

GPIB Connections 71

USB Connections 72

LAN Connections - site and private 72

Digital Port Connections 74

3 Getting Started 77

Using the Front Panel 78

Turn the Unit On 78

Select an Output Channel 78

Set the Output Voltage 79

Set the Output Current 79

Enable the Output 80

Use the Front Panel Menu 80

Remote Interface Configuration 83

USB Configuration 83

GPIB Configuration 83

LAN Configuration 84

Modifying the LAN Settings 85

Using the Web Interface 88

Using Telnet 89

Using Sockets 90

Securing the Interfaces 90

4 Operating the Power System 91

Programming the Output 92

Select a Channel View 92

Select an Output Channel 93

Set the Output Voltage 93

Set the Output Current 93

Set the Output Resistance 94

Set the Output Power 95

Set the Output Mode 96

Set the Slew Rate 96

Enable the Output 97

Sequence Multiple Outputs 98

Program the Output Relays 98

Set the Output Bandwidth 99

Set the Output Turn-Off Mode 100

Programming an Input Short 100

Enable Under-Voltage Inhibit 101

Stepping the Output 102

Synchronizing Output Turn-On 106

Synchronizing Output Turn-On Delays 106

Synchronizing Multiple Mainframes 109

Keysight N6700C Series User's Guide 4

Synchronization Operation 110

Programming Output Lists 111

Output Lists 111

Program an Output Pulse or Pulse Train 112

Program an Arbitrary List 114

Generating Arbitrary Waveforms 117

Arbitrary Waveform Description 117

Configuring Step Arbs 118

Configuring Pulse Arbs 118

Configuring Ramp Arbs 119

Configuring Trapezoid Arbs 120

Configuring Staircase Arbs 121

Configuring Exponential Arbs 122

Configuring Sinusoid Arbs 122

Configuring Constant-Dwell Arbs 123

Configuring an Arb Sequence 124

Configuring User-Defined Arbs 126

Configuring Steps Common to all Arbs 126

Running the Arb 127

Making Measurements 129

Basic DC Measurements 129

Measurement Ranges 129

Seamless Measurements 130

Simultaneous Measurements 130

Auxiliary Voltage Measurements 130

Using the Digitizer 132

Measurement Types 132

Programming the Digitizer 133

Synchronizing Digitizer Measurements 137

External Data Logging 142

Data Logging Functions 142

Select the Measurement Function and Range 142

Specify the Integration Period 143

Select the Elog Trigger Source 144

Initiate and Trigger the Elog 145

Periodically Retrieve the Data 145

Terminate the Elog 146

Using the Digital Control Port 147

Bi-directional Digital IO 147

Digital Input 148

External Trigger I/O 148

Fault Output 149

Inhibit Input 149

Fault/Inhibit System Protection 150

Output State 151

Using the Protection Functions 152

Protection Functions 152

Set the Over-Voltage Protection 153

5 Keysight N6700C Series User's Guide

Set the Over-Current Protection 153

Set the Over-Power Protection 154

Couple Output Protection 155

Query the Over-Temperature Margin 155

Set the Oscillation Protection 155

Watchdog Timer Protection 156

Clear Output Protection 156

System-Related Operations 157

Self-test 157

Instrument Identification 157

Instrument State Storage 158

Output Groups 158

Front Panel Display 160

Front Panel Keys 161

Password Protection 162

Mainframe Power Allocation 163

Mainframe Power Ratings 163

Mainframe Power Limit 163

Module Power Limit 163

Power Limit Allocation 164

Operating Mode Tutorial 165

Single-Quadrant Operation 165

Multi-Quadrant Operation 166

Keysight N679xA Load Module Operation 169

Index 172

Keysight N6700C Series User's Guide 6

Legal and Safety Information

Legal Notices

Safety Notices

Safety Symbols

Legal Notices

No part of this manual may be reproduced in any form or by any means (including electronic storage

and retrieval or translation into a foreign language) without prior agreement and written consent from

Keysight Technologies Inc. as governed by United States and international copyright laws.

Edition

Edition 2, February 2019

Published By

Keysight Technologies

550 Clark Drive, Suite 101

Budd Lake, New Jersey 07828

USA

Warranty

The material contained in this document is provided "as is," and is subject to being changed, without

notice, in future editions. Further, to the maximum extent permitted by applicable law, Keysight

disclaims all warranties, either express or implied, with regard to this manual and any information

contained herein, including but not limited to the implied warranties of merchantability and fitness for

a particular purpose. Keysight shall not be liable for errors or for incidental or consequential damages

in connection with the furnishing, use, or performance of this document or of any information contained

herein. Should Keysight and the user have a separate written agreement with warranty terms

covering the material in this document that conflict with these terms, the warranty terms in the

separate agreement shall control.

Certification

Keysight Technologies certifies that this product met its published specifications at time of shipment

from the factory. Keysight Technologies further certifies that its calibration measurements are

traceable to the United States National Institute of Standards and Technology, to the extent allowed

by the Institute's calibration facility, and to the calibration facilities of other International Standards

Organization members.

Legal and Safety Information

7 Keysight N6700C Series User's Guide

U.S. Government Rights

The Software is "commercial computer software," as defined by Federal Acquisition Regulation (“FAR”) 2.101.

Pursuant to FAR 12.212 and 27.405-3 and Department of Defense FAR Supplement (“DFARS”) 227.7202, the U.S.

government acquires commercial computer software under the same terms by which the software is customarily

provided to the public. Accordingly, Keysight provides the Software to U.S. government customers under its

standard commercial license, which is embodied in its End User License Agreement (EULA), a copy of which can

be found at http://www.keysight.com/find/sweula. The license set forth in the EULA represents the exclusive

authority by which the U.S. government may use, modify, distribute, or disclose the Software. The EULA and the

license set forth therein, does not require or permit, among other things, that Keysight: (1) Furnish technical

information related to commercial computer software or commercial computer software documentation that is

not customarily provided to the public; or (2) Relinquish to, or otherwise provide, the government rights in excess of

these rights customarily provided to the public to use, modify, reproduce, release, perform, display, or disclose

commercial computer software or commercial computer software documentation. No additional government

requirements beyond those set forth in the EULA shall apply, except to the extent that those terms, rights, or

licenses are explicitly required from all providers of commercial computer software pursuant to the FAR and the

DFARS and are set forth specifically in writing elsewhere in the EULA. Keysight shall be under no obligation to

update, revise or otherwise modify the Software. With respect to any technical data as defined by FAR 2.101,

pursuant to FAR 12.211 and 27.404.2 and DFARS 227.7102, the U.S. government acquires no greater than Limited

Rights as defined in FAR 27.401 or DFAR 227.7103-5 (c), as applicable in any technical data

Declaration of Conformity

Declarations of Conformity for this product and for other Keysight products may be downloaded from

the Web. Go to http://www.keysight.com/go/conformity and click on "Declarations of Conformity".

You can then search by product number to find the latest Declaration of Conformity.

Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC

This product complies with the WEEE Directive 2002/96/EC marketing requirement. The affixed

product label (see below) indicates that you must not discard this electrical/electronic product in

domestic household waste.

Product Category: With reference to the equipment types in the WEEE directive Annex 1, this product

is classified as "Monitoring and Control instrumentation" product.

Do not dispose in domestic household waste.

To return unwanted products, contact our local Keysight office, or see

http://www.keysight.com/environment/product for more information.

Keysight N6700C Series User's Guide 8

Legal and Safety Information

Safety Symbols

A WARNING notice denotes a hazard. It calls attention to an operating procedure, practice, or the

like that, if not correctly performed or adhered to, could result in personal injury or DEATH. Do not

proceed beyond a WARNING notice until the indicated conditions are fully understood and met.

A CAUTION notice denotes a hazard. It calls attention to an operating procedure, practice, or the

like that, if not correctly performed or adhered to, could result in damage to the product or loss of

important data. Do not proceed beyond a CAUTION notice until the indicated conditions are fully

understood and met.

Direct current

Alternating current

Frame or chassis terminal

Standby supply. Unit is not completely disconnected from AC mains when switch is off.

Risk of electric shock

Refer to accompanying documents

Earth ground terminal

The CE mark is a registered trademark of the European Community.

The ETL mark is a registered trademark of Intertek.

The RCM mark is a registered trademark of the Spectrum Management Agency of Australia.

South Korean Class A EMC Declaration

This equipment has been conformity assessed for use in business environments. In a residential environment this

equipment may cause radio interference. This EMC statement applies to the equipment only for use in business

environments.

Contains one or more of the 6 hazardous substances above the maximum concentration value (MCV), 40 Year

EPUP.

ISM1-A This text indicates that the instrument is an Industrial Scientific and Medical Group 1 Class A product (CISPER

11, Clause 4).

ICES/NMB-001 This text indicates product compliance with the Canadian Interference- Causing Equipment Standard (ICES-

001).

Legal and Safety Information

9 Keysight N6700C Series User's Guide

Safety Notices

The following general safety precautions must be observed during all phases of operation of this

instrument. Failure to comply with these precautions or with specific warnings or instructions

elsewhere in this manual violates safety standards of design, manufacture, and intended use of the

instrument. Keysight Technologies assumes no liability of the customer’s failure to comply with the

requirements.

General

Do not use this product in any manner not specified by the manufacturer. The protective

features of this product may be impaired if it is used in a manner not specified in the

operating instructions.

Environmental Conditions

Never use the instrument outside of the specified environmental conditions described in

the Environmental Characteristics of the specifications.

Ground the Instrument

This product is provided with protective earth terminals. To minimize shock hazard, the

instrument must be connected to the AC mains through a grounded power cable, with

the ground wire firmly connected to an electrical ground (safety ground) at the power

outlet. Any interruption of the protective (grounding) conductor or disconnection of the

protective earth terminal will cause a potential shock hazard that could result in injury

or death.

Before Applying Power

Verify that all safety precautions are taken. All connections must be made with the unit

turned off, and must be performed by qualified personnel who are aware of the hazards

involved. Improper actions can cause fatal injury as well as equipment damage. Note

the instrument's external markings described under "Safety Symbols".

Some power modules generate voltages exceeding 60 VDC

Ensure that instrument connections, load wiring, and load connections are either

insulated or covered so that no accidental contact with lethal output voltages can

occur.

Do Not Operate in an Explosive Atmosphere

Do not operate the instrument in the presence of flammable gases or fumes.

Do Not Remove the Instrument Cover

Only qualified, service-trained personnel who are aware of the hazards involved should

remove instrument covers. Disconnect the power cable and any external circuits before

removing instrument covers.

Keysight N6700C Series User's Guide 10

Legal and Safety Information

Autres manuels pour N6700C Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Keysight Technologies Alimentation

Keysight Technologies

Keysight Technologies N6900 Series Manuel de service

Keysight Technologies

Keysight Technologies 66332A Mode d'emploi

Keysight Technologies

Keysight Technologies E364xA Series Manuel

Keysight Technologies

Keysight Technologies E36200 Series Manuel utilisateur

Keysight Technologies

Keysight Technologies RP7900 Series Manuel de service

Keysight Technologies

Keysight Technologies N8921A Manuel utilisateur

Keysight Technologies

Keysight Technologies EDU36311A Manuel utilisateur

Keysight Technologies

Keysight Technologies N2779A Manuel utilisateur

Keysight Technologies

Keysight Technologies N6700 Manuel utilisateur

Keysight Technologies

Keysight Technologies E3646A Manuel

Keysight Technologies

Keysight Technologies 66312A Manuel utilisateur

Keysight Technologies

Keysight Technologies E364 A Series Manuel

Keysight Technologies

Keysight Technologies E36150 Series Manuel utilisateur

Keysight Technologies

Keysight Technologies E3620A Manuel de service

Keysight Technologies

Keysight Technologies E3633A Manuel utilisateur

Keysight Technologies

Keysight Technologies E36100 Series Manuel de service

Keysight Technologies

Keysight Technologies B2961A Manuel d'installation

Keysight Technologies

Keysight Technologies U3606B Manuel utilisateur

Keysight Technologies

Keysight Technologies RP7970 Series Manuel de service

Keysight Technologies

Keysight Technologies 6611C Manuel utilisateur

Keysight Technologies

Keysight Technologies U3606A Manuel utilisateur

Keysight Technologies

Keysight Technologies E36300 Series Manuel utilisateur

Keysight Technologies

Keysight Technologies U8030A Series Manuel utilisateur

Keysight Technologies

Keysight Technologies N69100 Series Manuel de service

Manuels Alimentation populaires d'autres marques

Monacor

Monacor PS-12CCD Manuel utilisateur

VOLTIMA

VOLTIMA MagicBox 15 Manuel utilisateur

Agilent Technologies

Agilent Technologies 6032A Manuel utilisateur

Miller

Miller Auto Deltaweld 452 Manuel utilisateur

BCP

BCP PUOUBK Feuille d'instructions

HC 2210 Manuel utilisateur

Puls

Puls CT5.241 Manuel utilisateur

OCZ

OCZ ZX1250W Manuel utilisateur

iseg

iseg ECH 238 Manuel utilisateur

Power

Power XXL A Series Manuel utilisateur

Agilent Technologies

Agilent Technologies 6631B Manuel utilisateur

Renogy

Renogy PHOENIX 300 Manuel utilisateur

HP 6200B Manuel de service

Epson

Epson Stylus Scan 2500 Manuel d'utilisation

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manuel utilisateur

Puls

Puls MiniLine ML50.100 Manuel utilisateur

Puls

Puls AS-Interface SLA4.100 Manuel utilisateur

Kenwood

Kenwood PS-60 Manuel utilisateur